Philips AZ1330 Bedienungsanleitung

AZ1330D

Docking Entertainment System

User manual

Important notes for users in the U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of

plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an

appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a

value of 3 Amp. If a plug without a fuse is used, the fuse at the distribution board

should not be greater than 3 Amp.

Note:The severed plug must be disposed of to avoid a possible shock hazard should it

be inserted into a 13 Amp socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the following code: blue = neutral (N),

brown = live (L). As these colours may not correspond with the colour markings iden-

tifying the terminals in your plug, proceed as follows:

• Connect the blue wire to the terminal marked N or coloured black.

• Connect the brown wire to the terminal marked L or coloured red.

• Do not connect either wire to the earth terminal in the plug, marked E (or e) or

coloured green (or green and yellow).

Before replacing the plug cover, make certain that the cord grip is clamped over the

sheath of the lead - not simply over the two wires.

Recording and playback of material may require consent. See Copyright Act 1956 and

The Performer’s Protection Acts 1958 to 1972.

Hearing Safety

Listen at a moderate volume.

• Using headphones at a high volume can impair your hearing. This product can produce sounds in

decibel ranges that may cause hearing loss for a normal person, even for exposure less than a

minute. The higher decibel ranges are offered for those that may have already experienced some

hearing loss.

• Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes of

sound. So after prolonged listening, what sounds "normal" can actually be loud and harmful to

your hearing. To guard against this, set your volume to a safe level before your hearing adapts and

leave it there.

To establish a safe volume level:

• Set your volume control at a low setting.

• Slowly increase the sound until you can hear it comfortably and clearly, without distortion.

Listen for reasonable periods of time:

• Prolonged exposure to sound, even at normally "safe" levels, can also cause hearing loss.

• Be sure to use your equipment reasonably and take appropriate breaks.

Be sure to observe the following guidelines when using your headphones.

• Listen at reasonable volumes for reasonable periods of time.

• Be careful not to adjust the volume as your hearing adapts.

• Do not turn up the volume so high that you can't hear what's around you.

• You should use caution or temporarily discontinue use in potentially hazardous situations.

• Do not use headphones while operating a motorized vehicle, cycling, skateboarding, etc.; it may

create a traffic hazard and is illegal in many areas.

AUX

VOLUME

DBB

DOCK

DOCK FOR

DOCKING ENTERTAINMENT SYSTE M AZ1330 D

for

MP3

-WMA PLAYBACK

6 x R20 • UM-1 • D-CELLS

& (

)

™

≤

∞

Supplied accessories

– AC power cord

– Remote control

– Docking kit

•1 x Apple iPod dock (pre-installed with the

main set)

•dock adaptors (8 adaptors for different iPod

types)

•1 dust cover (keep the dock connector

from covering dust and dirt)

Top and front panels (See 1)

1Telescopic antenna – improves FM

reception

2DOCK –

selects dock source

3Dock connector – connects iPod

player

VOLUME/

VOL +/- –

adjusts volume level

MODE – selects different play modes:

e.g. REPEAT or SHUFFLE (random

order)

6PROGRAM

For disc

– programs tracks and reviews the

program

For Tuner

– auto searches and stores radio

stations

7ALBUM/PRESET

+/- (

3,4

)

For MP3-CD/ WMA play:

– select albums

For Tuner

– selects a preset radio station

8/–opens/closes the disc tray

SOURCE:

–

selects CD/MP3-CD, DOCK

mode,Tuner or AUX

POWER

–

powers on/off the system

–

starts or pauses disc/DOCK playback

∞§

For disc

/ DOCK play:

– skips to the beginning of a current/

previous/ later track

– fast searches backwards and forwards

within a track

For Tuner:

– tunes to a radio station

–

stops disc playback;

–

erases a program

DBB – turns on/off bass enhancement

@p–3.5 mm stereo headphone socket

Helpful hints: The speakers will be muted

when headphones are connected to the set.

AUX jack

–

connects an external source

(3.5 mm socket)

$Battery door – opens to insert 6 x 1.5V

R-20/-UM1/D-cells

%Disc tray – load a disc

^iR –infrared sensor for remote control

Remote control (See 1)

&CD – selects disc mode

*TUNER – selects tuner mode

(DOCK – selects dock (iPod) source

)AUX– selects AUX mode

–

stops disc playback;

–

erases a program

™REPEAT – repeats a track/disc/all

programmed tracks

£SHUFFLE – turns on/off the random play

mode

≤DBB – turns on/off bass enhancement

∞MUTE –mutes or restores the volume

Power Supply

Whenever convenient, use the power supply

cord if you want to conserve battery life.

Make sure you remove the plug from the set

and wall outlet before inserting batteries.

Batteries

Main set (See 1)

• Insert 6batteries, type R-20, UM1 or D-

cells (not included, preferably alkaline) with

the correct polarity.

English Controls / Power Supply

Remote control

Important!

• Before using the remote control, remove

the insulation plastic tab as shown

in figure 9.

• If the remote control does not function

correctly or the operating range is

reduced, replace the battery with a new

(CR2025) type battery.

1Pull the battery tray out as shown

in figure 9.

2Replace a new battery according to polarity

indication, and fully insert the battery tray

back to the original position.

•Incorrect use of batteries can cause

electrolyte leakage and will corrode the

compartment or cause the batteries to burst:

•Do not mix battery types: e.g. alkaline with

carbon zinc. Only use batteries of the same

type for the set.

•When inserting new batteries, do not try to

mix old batteries with the new ones.

• Remove the batteries if the set is not to be

used for a long time.

Batteries contain chemical substances, so

they should be disposed of properly.

Using AC power

1Check if the power/mains voltage, as shown

on the type plate located on the

bottom of the set, corresponds to your

local power supply. If it does not, consult your

dealer or service center.

2Connect the power cord to the

AC~ MAINS inlet and the wall socket.The

set is now ready for use.

3To switch the set off completely, withdraw

the power cord from the wall socket.

4Install the unit near the AC outlet and where

the AC power plug can be easily reached.

• Disconnect the power cord from the wall

socket to protect your set during heavy

thunderstorms. Children could seriously injure

themselves as the free end of the cable may

still be live if only the connector is removed

from the MAINS socket at the back of the

unit.

The type plate is located on the

bottom of the set.

Auto power saving

•In CD and DOCK mode, if AZ1330D is in

the PAUSE position for 5 minutes, it will auto

switch to the stop position.

•In CD and DOCK mode, if AZ1330D is in

the STOP position for 15 minutes, it will auto

switch to standby to save power.

Helpful hints:

– To avoid unnecessary energy consumption,

always press POWER on the set to power

off the set after using the set.

CAUTION

- Visible and invisible laser radiation.

If the cover is open, do not look at

the beam.

- High voltage! Do not open.You run

the risk of getting an electric shock.

The machine does not contain any

user-serviceable parts.

- Modification of the product could

result in hazardous radiation of

EMC or other unsafe operation.

This set complies with the radio

interference requirements of the

European Union.

Power Supply

Basic functions

Switching on/off the set

1To switch on, press POWER.

➜Display lights up.The system will switch to

the last selected source.

2To switch off, press POWER again.

➜Display lights off.

Adjusting volume and sound

Adjust the sound with the VOLUME and

DBB controls.

Digital tuner

Tuning to radio stations

1Press repeatedly SOURCE (or TUNER

on the remote control) to select FM or

MW.

➜“TUNER” is displayed briefly, then the

radio station frequency, waveband and, if

programmed, a preset number are shown

(See 2).

2Press and hold ∞or §until the frequency in

the display starts running.

➜The radio automatically tunes to a station

of sufficient reception. Display shows

“SEARCH” during automatic tuning.

3Repeat step 2 if necessary until you find the

desired station.

• To tune to a weak station, press ∞or §

briefly and repeatedly until you have found

optimal reception.

To improve radio reception:

• For FM,extend, incline and turn the

telescopic aerial. Reduce its length if the signal

is too strong.

• For MW,the set uses a built-in aerial. Direct

this aerial by turning the whole set.

Programming radio stations

You can store 15 FM and 10 MW radio

stations in the memory manually or

automatically (Auto store).

Manual programming

1Tune to your desired station (see Tuning to

radio stations).

2Press PROG to activate programming.

➜Display: PROG flashes.

3Press ALBUM/PRESET +/-

(ALBUM/PRESET

3,4

on the remote

control ) once or more to allocate a number

(from 1 to 25).

4Press PROG to confirm.

5Repeat steps 1-4 to store other stations.

Helpful hints:

– You can erase a preset station by storing

another frequency in its place.

Autostore

Autostore automatically starts programming

radio stations from preset 1. Any previous

presets e.g. manually programmed will be

erased.

1Press repeatedly SOURCE (or TUNER

on the remote control) to select FM or

MW.

2Press PROG until “AUTO” flashes.

➜Available stations are programmed (MW

or FM). After all stations are stored, the

first autostore preset station will then

automatically play.

To listen to a preset or autostore

station

Press the ALBUM/PRESET +/-

(ALBUM/PRESET

3,4

on the remote

control ) buttons once or more until the

desired preset station is displayed.

Basic Function/Radio MP3-CD/CD Player

About MP3

The music compression technology MP3

(MPEG1 Audio Layer 3) significantly reduce

the digital data of an audio CD while

maintaining CD quality sound.

•Getting MP3 files: you can either download

legal music files from the internet to your

computer hard disc, or create such files by

converting audio CD files in your computer

through appropriate encoder software.

(128kbps bit rate or higher is recommended

for MP3 files.)

•Creating a MP3 CD: burn the music files

from your computer hard disc on a CDR or

CDRW using your CD burner.

Helpful hints:

– Make sure that the file names of the MP3 files

end with .mp3 or .wma.

– Number of albums: maximum 100.

– Number of tracks: maximum 999.

– The length of file names affects the number of

tracks for playback. With shorter file names,

more files can be burned on a disc.

Playing a disc

This player plays Audio Discs including

CD-R/ CD-RW, MP3 CD and WMA. Do not

try to play a CD-ROM, CD-I, CDV,VCD,

DVD or computer CD.

IMPORTANT!

•CDs encoded with copyright protection

technologies by some record companies may

be unplayable by this product.

•DRM-protected WMA disc is not supported.

1Press repeatedly SOURCE (CD on the

remote control) to select CD source.

➜Display shows flashing “READ” if CD

source is selected (see 3).

➜“ NO DISC” will be displayed if CD is not

loaded.

3Press /to open the disc door.

4Insert a disc with the printed side facing up

and press the disc door gently to close.

➜The disc scanning of MP3-CD may run

longer than audio CD.

➜Display: The total number of tracks

appears (and album number for

MP3/WMA) (see 4).

5Press

to start playback.

➜First the song title of the track scrolls

across the display, then the track number

and the elapsed playing time are displayed.

For MP3-CD/ WMA only:

➜The current track number (TRK) and

album number (ALB) will be displayed

interchangeably.

6To pause playback press

➜Display:

and the elapsed playing time

flash.

7Press

again to resume playback.

8To stop playback, press

Helpful hints:

The disc playback will also stop when:

– you open the disc compartment door;

– you select FM,MW,AUX or DOCK;

– the disc has reached the end of the playback.

Selecting a different track

•Press ∞or §once or repeatedly until the

desired track number appears in the display.

For MP3-CD/WMA: First press

ALBUM/PRESET +/- (ALBUM/

PRESET

3,4

on the remote control )

once or more to find your album.

•In the pause/stop position, press 2; to start

playback.

MP3-CD/CD Player

Finding a passage within a

track

1During playback, press and hold down

∞or §

➜The disc is played at high speed and low

volume.

2When you recognize the passage you want,

release

∞or §

➜Normal playback resumes.

Programming tracks

You may store up to 20 tracks in the desired

sequence. If you like, store any track more

than once.

1In the stop position, press

∞

to select

your desired track number.

•For MP3-CD/WMA: First press

ALBUM/PRESET +/- (ALBUM/PRE-

SET

3,4

on the remote control ) once or

more to find your album.

2Press PROG to store desired track.

➜Display shows “PRO 2” , indicating the

programmed location (See 5).

•If you attempt to program without first

selectig a track, display will show “SELECT

TRACK” briefly, then the total track number

and playing time.

3Repeat steps 1to 2to select and store all

desired tracks.

4Press

to play the program.

➜“PROG” is dispalyed during program

playback.

To review your program

In the stop position, press and hold PROG 3

seconds.

➜The display shows all the stored tracks

(and album numbers for MP3) in

sequence.

Helpful hints:

– Display shows “NO PROG” if no track is

programmed.

– If you try to store more than 20 tracks, no

track can be stored and the display will show

”PROGRAM FULL”.

To erase a program

You can erase a program by:

– pressing

(twice during playback or once in

the stop position);

– selecting FM,MW,AUX or DOCK;

– pressing POWER to power off;

– opening the disc door.

➜ “PROGRAM CLEAR” scrolls across the

display once, and “PROG” disappears.

Selecting different play

modes (See 6)

You can select and change the various play

modes before or during playback, and

combine play modes with PROG.

REP – plays the current track continuously.

REP ALL – plays the entire disc/program

continuously.

SHUF – plays all tracks in random order.

REP ALL SHUF – plays all tracks in

random order continuously.

1To select play modes,press MODE on the

set (REPEAT or SHUFFLE on the remote

contorl) once or more.

2Press 2; to start playback if in the stop

position.

➜Shuffle play will start automatically soon

after shuffle mode is selected.

3To select normal playback, press MODE on

the set (REPEAT or SHUFFLE on the

remote control) repeatedly until the various

play modes are no longer displayed.

–You can also press 9to cancel your play

modes.

Helpful hints:

– Shuffle (SHUF and REP ALL SHUF) play is

not available in the program mode.

MP3-CD/CD Player

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Dockingstation Handbücher

Philips

Philips LFH 9160 Bedienungsanleitung

Philips

Philips DCB-352 Bedienungsanleitung

Philips

Philips DCM109/79 Bedienungsanleitung

Philips

Philips AJ300D/05 Bedienungsanleitung

Philips

Philips DC291/37 Bedienungsanleitung

Philips

Philips DCB291/05 Bedienungsanleitung

Philips

Philips Fidelio DS9800W Bedienungsanleitung

Philips

Philips DC910/98 Bedienungsanleitung

Philips

Philips DCP746/37 Bedienungsanleitung

Philips

Philips DC350/12 Bedienungsanleitung

Philips

Philips AJ7040D Bedienungsanleitung

Philips

Philips Fidelio Docking speaker DS 3000 Bedienungsanleitung

Philips

Philips AJ7034D/05 Bedienungsanleitung

Philips

Philips DC910W Bedienungsanleitung

Philips

Philips DC295 Bedienungsanleitung

Philips

Philips Fidelio DCW8010 Bedienungsanleitung

Philips

Philips AJ300D Bedienungsanleitung

Philips

Philips SGP6031BB/27 Bedienungsanleitung

Philips

Philips DCB852 Bedienungsanleitung

Philips

Philips AJ300D/37B Bedienungsanleitung

Philips

Philips STREAMIUM WAC7500 Bedienungsanleitung

Philips

Philips DLA99901/10 Bedienungsanleitung

Philips

Philips DCP750 Bedienungsanleitung

Philips

Philips AJ300D - AJ Clock Radio Bedienungsanleitung

Beliebte Dockingstation Handbücher anderer Marken

Sony

Sony Dream Machine XDR-DS12iP Bedienungsanleitung

ATEN

ATEN UC-2000 Bedienungsanleitung

Xcellon

Xcellon HDD-202 Bedienungsanleitung

Dok

Dok CR09 Bedienungsanleitung

IOGear

IOGear Travel Pro GUD3C09 Bedienungsanleitung

RKI

RKI SDM-E2 Bedienungsanleitung

iHome

iHome iP15 Bedienungsanleitung

VITURE ONE

VITURE ONE MOBILE DOCK Bedienungsanleitung

Lindy

Lindy 42984 Bedienungsanleitung

CipherLab

CipherLab 8001 Bedienungsanleitung

Pyle

Pyle PIPDSP2 Bedienungsanleitung

Avol

Avol AS2350 Bedienungsanleitung

Datalogic

Datalogic JoyaTouch Bedienungsanleitung

Targus

Targus DOCK315EUZ Bedienungsanleitung

Akasa

Akasa DuoDockX3 AK-DK08U3-BK Bedienungsanleitung

Sirius Satellite Radio

Sirius Satellite Radio SUBX2082808a Bedienungsanleitung

OWC

OWC Thunderbolt Dock Bedienungsanleitung

Onyx

Onyx XDNX1HK Bedienungsanleitung