Philips PerfectCare 9000 Series Bedienungsanleitung

PerfectCare

9000 Series

PerfectCare

9000 Series

5 6

7 8 109

1 3 42

1416 15 1113 12

17 18

4239 001 16451

User manual

사용자 설명서

Manual pengguna

คู่มือผู้ใช้

Hướng dẫn sử dụng

用户手册

使用手冊

Do not open the EASY DE-CALC knob when the device is powered on, or

immediately after use.

장치의 전원이 켜져 있을 때또는 사용 직후에는 EASY DE-CALC

조절기를 열지 마십시오.

Jangan buka tombol EASY DE-CALC apabila peranti dihidupkan

atau sebaik sahaja selepas digunakan.

 EASY DE-CALC  

Không mở núm EASY DE-CALC khi thiết bị được bật nguồn hoặc ngay sau khi sử dụng.

请勿在设备接通电源或使用后立即打开 EASY DE-CALC 旋钮。

請勿在裝置電源開啟時或剛使用完畢後，開啟 EASY DE-CALC 簡易除鈣

旋鈕。

CLICK

2 hr

1 3

75 5 7

350 ml

42 3

English 6

한국어 15

Bahasa Melayu 24

ภาษาไทย 33

Tiếng Việt 42

简体中文 51

繁體中文 60

6ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet from the support that

Philips oers, register your product at www.philips.com/welcome.

Read this user manual, the important information leaet, and the quick start guide carefully before

you use the appliance. Save them for future reference.

Product overview (Fig. 8)

1 Steam supply hose

2 Steam trigger

3 Intelligent automatic steam button

4 Iron ready light

5 Soleplate

6 ActiveSense camera

7 Iron platform

8 Carry lock release button

9 Filling hole

10 Detachable water tank

11 Steam supply hose storage compartment

12 Cord storage compartment

13 Mains cord with plug

14 EASY DE-CALC knob

15 On/o button with light

16 Calc alert

17 Max steam setting light

18 Low water alert light

Preparing for use

Type of water to use

This appliance has been designed to be used with tap water. However, if you live in an area

with hard water, fast scale build-up may occur. Therefore, it is recommended to use distilled or

demineralized water (50% demineralized/distilled water mixed with water could be used as well) to

prolong the lifetime of the appliance.

Warning: Do not use perfumed water, water from the tumble dryer, vinegar, starch, descaling

agents, ironing aids, chemically descaled water or other chemicals, as they may cause water

spitting, brown staining or damage to your appliance.

Getting the product ready

Fill the water tank before every use or when the ‘low water alert’ light ashes. You can rell the

water tank at any time during use.

1 Remove the water tank from the appliance and ll it with water up to the MAX indication.

2 Put the water tank back into the appliance by tting the bottom part into the appliance rst.

3 Push in the top part of the water tank until it locks into place (‘click’).

Put the mains plug in an earthed wall socket and press the on/o button to switch on the steam

generator. Wait until the ‘iron ready’ light lights up continuously. Once your appliance is ready, you

will also hear a short beep.

Note: For rst time use, we recommend you to place the iron on the ironing board before you turn

on the appliance for optimum performance.

There will be sound from the base of your product due to the water being pumped for steam

generation.

ENGLISH

Low water alert light

When the water tank is almost empty, the ‘low water alert’ light ashes. Fill the water tank and

press the steam trigger to let the appliance heat up again. When the ‘iron ready’ light lights up

continuously, you can continue steam ironing.

Using your appliance

ActiveSense technology

Your appliance comes with the world’s very rst fabric sensing technology in irons

called ActiveSense. It works with articial intelligence recognizing fabrics during

ironing with built-in camera, adjusting the ideal temperature and steam amount

automatically. You can also leave your iron on the ironing board without risk of

burns.

The ActiveSense technology enables you to iron all types of ironable fabrics,

in any order, without adjusting the iron temperature setting.

The ‘iron ready’ light can light up steadily in either blue or white,

corresponding to the level of temperature/steam needed (normal and high

for the respective light), based on the fabric detected.

Fabrics with these symbols are ironable (Fig. 9), for example linen, cotton,

polyester, silk, wool, viscose and rayon.

Note: Do not iron on prints, even if the fabric around is ironable.

For certain delicate fabric and nishing (e.g: suede, velvet, metallic weaving,

sequins), it is recommended to steam a short distance above the garment.

Fabrics with this symbol are not ironable (Fig. 10). These fabrics include

synthetic fabrics such as Spandex or elastane, Spandex-mixed fabrics and

polyolens.

During ironing, you can place the iron either on the iron platform or

horizontally on the ironing board. Thanks to the ActiveSense technology,

the soleplate will not damage the ironing board cover (Fig. 11).

Note: There may be some steam observed when the iron is resting for a

longer period of time. This is normal as it is part of the system process to

ensure the soleplate is at the right temperature during rest. During this

process, the ‘iron ready’ light will be breathing in blue.

Note: Minimise touching the front of the iron as it will get warm.

ENGLISH

Ironing with intelligent automatic steam mode

Your appliance comes with intelligent automatic steam thanks to DynamiQ

sensor technology which recognizes how and when your iron is moving.

When you turn on your appliance, this mode will be activated by default

(Fig. 12). Coupled with ActiveSense technology, your iron will steam

automatically the right amount of steam based on your movements and the

fabric type without the need to use the steam trigger.

In intelligent automatic steam mode, steam comes out automatically when

you move the iron and stops when you stop moving the iron (Fig. 13). You

can still press the steam trigger in this mode to activate the steam when the

iron is not moving.

Note: For your safety, in intelligent automatic steam mode, the steam

stops when the iron is lifted up.

Ensure that the board is tting to the size and weight of steam generator.

Ironing in manual mode

You can control the amount of steam manually during ironing by turning o

the intelligent automatic steam mode .

-To exit the intelligent automatic steam mode, press the intelligent

automatic steam button (Fig. 14). The intelligent automatic steam light

turns o. You need to press the steam trigger to continue your ironing.

-In manual mode, ActiveSense technology will still adjust the

temperature and steam amount automatically to dierent fabrics, but

you need to press the steam trigger to activate steam release.

Warning: Never direct steam at people.

Note: For best result on tough fabrics such as cotton, linen and denim,

keep the steam trigger pressed continuously when you move the iron over

the fabric (Fig. 15). Then move the iron over the same area a few more

times without steam to dry the fabric.

Note: For the best results on silk and shiny synthetic fabrics, it is

recommended to keep the steam trigger pressed continuously while

ironing.

Steam boost function

The steam boost function is designed to help tackle dicult creases.

-Press the steam trigger twice quickly to activate the steam boost

function. The appliance releases 3 powerful shots of steam (Fig. 16).

ENGLISH

Vertical ironing

Hot steam is emitted from the iron. Never attempt to remove creases

from a garment that someone is wearing. Do not apply steam near your or

someone else’s hand.

You can use the iron in vertical position to remove wrinkles from hanging

fabrics.

1 Hold the iron in vertical position, press the steam trigger and touch the

garment slightly with the soleplate (Fig. 17).

Note: For your safety, the intelligent automatic steam mode is not

available for vertical ironing.

MAX setting

For higher amount of steam, you can use the MAX setting.

1 Press and hold the on/o button for 2 seconds until the MAX light turns

white (Fig. 18).

Note: In Max setting, your appliance will always give the maximum steam

amount, while the temperature will still adjust automatically.

2 The appliance returns to normal steam mode automatically after 15

minutes to save energy.

3 To directly switch o the MAX setting at any time, press and hold the on/

o button for 2 seconds until the MAX light goes o.

Auto shut-o

-To save energy, the appliance enters the standby mode if it has not

been used for 4-5 minutes. The light in the on/ o button starts to ash

(Fig. 19).

-To activate the appliance again, press the on/o button or the steam

trigger. The appliance starts to heat up again.

-The appliance switches o automatically if it has not been used for

another 10 minutes after it enters the standby mode. The light in the on/

o button goes o.

IMPORTANT - EASY DE-CALC

It is very important to use the EASY DE-CALC function as soon as the

EASY DE-CALC light starts to ash (Fig. 20) and the appliance beeps

continuously.

The EASY DE-CALC light ashes and the appliance beeps continuously

after about a month or 10 ironing sessions to indicate that the appliance

needs to be descaled. Perform the following EASY DE-CALC procedure

before you continue ironing.

1 Remove the plug from the wall socket.

2 Place the appliance on the edge of the tabletop.

2 sec

ENGLISH

3 Hold a cup (with a capacity of at least 350ml) under the EASY DE-CALC

knob and turn the knob anticlockwise (Fig. 21).

4 Remove the EASY DE-CALC knob and let the water with scale particles

ow into the cup (Fig. 22).

5 When no more water comes out of the appliance, reinsert the EASY DE-

CALC knob and turn it clockwise to fasten it (Fig. 23).

6 You can continue using your iron immediately after completing the

EASY DE-CALC procedure.

Note: If you are performing the EASY DE-CALC procedure immediately after ironing, unplug the

appliance and let it cool down for at least two hours before you perform the procedure.

IMPORTANT – Descaling the soleplate

If you do not use the EASY DE-CALC function regularly, scale particles may build up in the

soleplate and brown stains may come out of the soleplate during ironing. In this situation, you

need to descale the soleplate by following the procedure below. We advice you to repeat the

procedure twice to better clean the soleplate.

To avoid the risk of burns, unplug the appliance and let it cool down for at

least two hours before you descale the soleplate (Fig. 24).

1 Remove the plug from the wall socket.

2 Place the appliance on the edge of the tabletop.

3 Make sure that the water tank is empty.

350 ml

2 hr

ENGLISH

4 Hold a cup (with a capacity of at least 350ml) under the EASY DE-CALC

knob and turn the knob anticlockwise (Fig. 25).

5 Remove the EASY DE-CALC knob and let the water with scale particles

ow into the cup (Fig. 26).

6 Hold the appliance in the position that EASY DE-CALC opening is facing

up and pour 900ml distilled water into the opening (Fig. 27).

Note: Be mindful on the heavy weight of the appliance when you tilt it.

7 Keep the EASY DE-CALC opening facing up, reinsert the EASY DE-CALC

knob and turn it clockwise to fasten it (Fig. 28).

8 Put the appliance back on a stable and even surface. Plug in the

appliance and switch it on (Fig. 29).

9 Wait for 5 minutes for the appliance to heat up.

10 Switch o DynamiQ function by pressing the intelligent automatic steam

button on the top of the iron handle.

350 ml

900 ml

ENGLISH

11 Keep the steam trigger pressed continuously while you move the iron

on a piece of thick cloth for 3 minutes (Fig. 30).

Warning: Hot, dirty water comes out of the soleplate.

12 Stop moving the iron when no more water comes out.

13 You can continue to use the appliance immediately. Otherwise unplug

the appliance after the descaling is completed.

Storage

1 Switch o the appliance and unplug it.

2 Put the iron on the iron platform. Push the carry lock to lock the iron

onto the platform.

3 Remove the water tank and empty it.

4 Wrap the steam supply hose around the base.

5 Slot it into the supply hose storage compartment by pushing the hose

through the gap (Fig. 31).

6 Fold the mains cord with the velcro provided, and insert it into the cord

storage compartment (Fig. 32).

7 You can carry the appliance with one hand by the handle of the iron.

Note: Do not carry the appliance by holding the water tank release lever

Note: If there is calc/bre build up around the ActiveSense camera,

remove it gently with a cotton swab or equivalent.

Troubleshooting

This chapter summarises the most common problems you could encounter with the appliance. If

you are unable to solve the problem with the information below, visit www.philips.com/support

for a list of frequently asked questions or contact the Consumer Care Centre in your country

(+65 6882 3999).

Problem Possible cause Solution

The ironing board

cover becomes

wet or there are

water droplets on

the garment during

ironing.

Steam has condensed on the

ironing board cover after a long

ironing session.

Replace the ironing board cover if the

foam material has worn out. You can

also add an extra layer of felt material

under the ironing board cover to prevent

condensation on the ironing board. You

can buy felt in a fabric shop.

You have an ironing board cover

that is not designed to cope

with the high steam rate of the

appliance.

Put an extra layer of felt material under

the ironing board cover to prevent

condensation on the ironing board. You

can buy felt in a fabric shop.

Automatic steam mode has

been used for a long period of

time.

Switch o the automatic steam mode

and use the manual trigger to activate the

steam when needed.

Andere Handbücher für PerfectCare 9000 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Philips Eisen Handbücher

Philips

Philips GC7430 Bedienungsanleitung

Philips

Philips GC4800 series Bedienungsanleitung

Philips

Philips GC2900 series Bedienungsanleitung

Philips

Philips GC7530 Bedienungsanleitung

Philips

Philips GC4400 series Bedienungsanleitung

Philips

Philips Azur Pro GC4880 Series Bedienungsanleitung

Philips

Philips GC650/02 Bedienungsanleitung

Philips

Philips ELANCE GC3006 Bedienungsanleitung

Philips

Philips GC9540/07 Bedienungsanleitung

Philips

Philips GC4887/30 Bedienungsanleitung

Philips

Philips HI540/22 Bedienungsanleitung

Philips

Philips GC 6606/20 Bedienungsanleitung

Philips

Philips GC1420 Bedienungsanleitung

Philips

Philips Walita RI6833 Bedienungsanleitung

Philips

Philips PerfectCare Elite Plus GC9660/30 Bedienungsanleitung

Philips

Philips PerfectCare Expert Plus GC8900 Series Bedienungsanleitung

Philips

Philips GC4500 series Bedienungsanleitung

Philips

Philips GC330 Series Bedienungsanleitung

Philips

Philips GC8261 Bedienungsanleitung

Philips

Philips Powerlife Plus GC2982/30 Bedienungsanleitung

Philips

Philips GC4521/20 Bedienungsanleitung

Philips

Philips GC142/02 Bedienungsanleitung

Philips

Philips GC8600 Series Bedienungsanleitung

Philips

Philips EasySpeed GC1020 series Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Texi

Texi Hestia Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

dyras

dyras ESI-2400AC Bedienungsanleitung

GE 169061 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 GC Bedienungsanleitung

AEG

AEG DBS 5591 Bedienungsanleitung

Braun

Braun TexStyle 9 12790002 Bedienungsanleitung