Philips Bodine B426 Bedienungsanleitung

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

SAVE THESE INSTRUCTIONS

THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.

THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.

A Division of Philips Electronics North America Corporation

236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.bodine.com

70042609

EMERGENCY LIGHTING EQUIPMENT

Installation Instructions

1. To prevent high voltage from being present on yellow/black & yellow

output leads prior to installation, inverter connector must be open.

Do not join inverter connector until installation is complete and AC

power is supplied to the emergency ballast.

2. This product is for use with one or two twin-tube, double twin-tube

(quad), or triple twin-tube compact ﬂuorescent lamps shown in the

Lamp Rating Chart.

3. Make sure all connections are in accordance with the National Electrical Code and any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter

connector of the emergency ballast before servicing.

5. This emergency ballast is for factory or ﬁeld installation.

6. This product is suitable for damp locations where the ambient temperature is 0°C minimum, +50°C

maximum. Product is not suitable for heated air outlets and wet or hazardous locations.

7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not ﬁeld replaceable.

Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualiﬁed service personnel.

03/25/11

B426

Ni - Cd

Lamp Rating Chart

Operates One or Two (2-Pin) Lamps

Lamp Type Wattage Base

Twin-Tube 13 GX23

Quad 10,13,18,26 G24d

Triple 13,18,26 GX24d

STEP #1

WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON YELLOW/BLACK &

YELLOW OUTPUT LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN.

DO NOT JOIN INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER

IS SUPPLIED TO THE EMERGENCY BALLAST.

STEP #2 WIRING THE EMERGENCY BALLAST

> See back page for detailed wiring schematics. The emergency ballast can be used with one- or two- lamp

ﬁxtures, and operates one or two lamps in the emergency mode.

> Cut ﬁxture wire between the lamp holder and AC ballasts and connect the blue and blue/white emergency

ballast wires to the AC ballast and the yellow and yellow/black wires to the lamp holder.

> On switched ﬁxtures, an additional unswitched hot (120 or 277 VAC) wire must be run to the junction box

and connected to the emergency ballast.

> Connect LED by matching violet and brown leads. For optional tabbed LED, connect violet lead to positive

(+) tab (marked). For Illuminated Test Switch (ITS) connect as shown on wiring diagrams by matching

violet and brown leads and connecting the black leads to the emergency ballast white and white/black

wires.

> After installation is complete, supply AC power to the emergency ballast and join the inverter connector.

NOTE: Make sure that the necessary branch circuit wiring is available. An unswitched

source of power is required. The emergency ballast must be fed from the same

branch circuit as the AC ballast.

INSTALLING THE EMERGENCY BALLAST

> Disconnect AC power from the ﬁxture.

> Refer to illustration below to install the emergency ballast and test/monitor plate. Make electrical

connections in accordance with the National Electrical Code and any local regulations. The test/monitor plate may be

installed close to the ﬁxture in the ceiling or at a remote location (up to 50 feet). The emergency ballast may be

remotely installed up to 1/2 the distance the AC ballast manufacturer recommends remoting the AC ballast from

the lamp, or up to 50 feet, whichever is less. If no AC ballast is used, the emergency ballast can be remotely

mounted up to 50 feet away. Note: A switch box is not supplied.

INSTALLATION

STANDARD INSTALLATION REMOTE INSTALLATION

Emergency ballast No Shading – Equipment supplied by

others

1 – Flexible conduit (supplied) to connect ballast wires.

2 – Existing conduit to run existing wires to lamp holder (AC ballast on junction box). If AC ballast is on reﬂector, run

yellow, yellow/black, blue/white and blue wires from emergency ballast through this conduit.

3 – AC line in.

4 – Conduit and junction box (not supplied), necessary for remote installation.

INSTALLATION

When AC power is applied, the charging indicator light is illuminated, indicating that the battery is being charged. When

power fails, the emergency ballast automatically switches to emergency power (internal battery), providing at least

90 minutes of emergency lighting. This emergency ballast will operate one or two 10 W or 13 W lamps for a minimum of

120 minutes.

Although no routine maintenance is required to keep the emergency ballast functional, it should be checked periodically to

ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated.

2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. One or two

lamps should operate at reduced illumination.

3. Conduct a full length discharge test once a year. One or two lamps should operate at reduced

illumination for at least the rated duration.

! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !

OPERATION

STEP #3 EMERGENCY BALLAST QUICK CHECK AND LABELING

> For short-term testing of the emergency function, the battery must be charged for at least two hours. The

emergency ballast must be charged for at least 24 hours before conducting a long-term test.

> In a readily visible location, attach the label "CAUTION - This Unit Has More Than One Power Connection Point.

To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency

Power Supplies Before Servicing."

MAINTENANCE

FIG F TWO-LAMP FIXTURE WITH ADVANCE H-2B13-TP OR

ROBERTSON H213P BALLASTS

FIG D ONE–LAMP FIXTURE, ONE AUTOTRANSFORMER AC BALLAST

FIG B TWO–LAMP FIXTURE, TWO AUTOTRANSFORMER AC BALLASTS

FIG E TWO-LAMP FIXTURE WITHOUT AC BALLAST

FIG C ONE–LAMP FIXTURE, ONE SIMPLE REACTOR AC BALLAST

FIG A TWO–LAMP FIXTURE, TWO SIMPLE REACTOR AC BALLASTS

WIRING DIAGRAM

EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

FIG G TWO LAMP FIXTURE, WITH ADVANCE VH-2B13-TP BALLAST FIG H TWO-LAMP FIXTURE, ONE MAGNETIC AC BALLAST

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

BLACK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

BLACK

AC BALLAST 1

AC BALLAST 2

BLACK 120V

ORANGE 277V

BLU/WHT

BLUE

YELLOW

YEL/BLK

LAMP 2

(CAP UNUSED LEAD)

LAMP 1 ( )

EMERGENCY

UNSWITCHED HOT

WALL

SWITCH

COMMON

WHT/BLK

WHITE

( )

EMERGENCY

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

BLACK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

BLACK

AC BALLAST 1

AC BALLAST 2

BLACK 120V

ORANGE 277V

WHT/BLK

BLUE

YELLOW

YEL/BLK

LAMP 2

(CAP UNUSED LEAD)

LAMP 1 ( )

EMERGENCY

UNSWITCHED HOT

WALL

SWITCH

COMMON

BLACK

BLACK BLUE

WHITE

BLUE

BLU/WHT

WHITE

( )

EMERGENCY

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

BLACK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

BLACK

AC BALLAST

BLACK 120V

ORANGE 277V

WHT/BLK

BLUE

YELLOW

(CAP UNUSED LEAD)

LAMP

WHITE

UNSWITCHED HOT

WALL

SWITCH

COMMON

YEL/BLK

BLU/WHT

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

BLACK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

BLACK

AC BALLAST

BLACK 120V

ORANGE 277V

WHT/BLK

BLUE

YELLOW

YEL/BLK

(CAP UNUSED LEAD)

LAMP

WHITE

UNSWITCHED HOT

WALL

SWITCH

COMMON

BLACK BLUE

WHITE BLU/WHT

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

BLACK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

BLACK

(CAP UNUSED LEAD)

BLACK 120V

ORANGE 277V

BLU/WHT

BLUE

YELLOW

YEL/BLK

LAMP 2

CAP EACH

UNUSED LEAD

LAMP 1

UNSWITCHED HOT

COMMON

WHT/BLK

WHITE

( )

EMERGENCY

( )

EMERGENCY

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

BLACK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

BLACK

BLUE

BALLAST

WHITE

BLACK 120V

ORANGE 277V

BLACK

WHT/BLK

BLUE

YELLOW

UNSWITCHED HOT

COMMON

WALL

SWITCH

LAMP 2

(CAP UNUSED LEAD)

LAMP 1 ( )

EMERGENCY

RED BLU/WHT

( )

EMERGENCY

YEL/BLK

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

BLACK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

BLACK

BLUE

BALLAST

WHITE

BLACK 120V

ORANGE 277V

BLACK

WHT/BLK

BLUE

YELLOW

UNSWITCHED HOT

COMMON

WALL

SWITCH

LAMP 2

(CAP UNUSED LEAD)

LAMP 1 ( )

EMERGENCY

WHITE BLU/WHT

( )

EMERGENCY

YEL/BLK

CHARGING

INDICATOR

LIGHT

INVERTER

CONNECTOR

TEST

SWITCH

BLACK

WHITE

VIOLET

BROWN

WHT/BLK

RED

WHITE

BLACK

(CAP UNUSED LEAD)

LAMP 1 ( )

EMERGENCY

( )

EMERGENCY

BLUE

BALLAST

WHITE

BLACK 120V

ORANGE 277V

WHITE

BLACK

WHT/BLK

BLUE

YELLOW

UNSWITCHED HOT

COMMON

WALL

SWITCH

LAMP 2

YEL/BLK

BLU/WHT

This emergency ballast is also compatible with other AC ballasts.

Please contact factory with AC ballast model number for wiring diagrams.

Inhaltsverzeichnis

Andere Philips Beleuchtungsausrüstung Handbücher

Philips

Philips FBH 020 Bedienungsanleitung

Philips

Philips VARI-Lite VL4000 Bedienungsanleitung

Philips

Philips RD6 Bedienungsanleitung

Philips

Philips Lightstrip Plus 71901/U8 Series Bedienungsanleitung

Philips

Philips hue Bedienungsanleitung

Philips

Philips TrueLine RC530B ELP3 Bedienungsanleitung

Philips

Philips 57946-17-16 Bedienungsanleitung

Philips

Philips hue 40801 Series Bedienungsanleitung

Philips

Philips GreenPower TLED InstantFit Bedienungsanleitung

Philips

Philips SM500T Bedienungsanleitung

Philips

Philips FlexTune Bedienungsanleitung

Philips

Philips SP160P LED40S 840 W60L60 PSU SI Benutzerhandbuch

Philips

Philips Selecon SPX 15-35 Bedienungsanleitung

Philips

Philips ILS-CL-8RES Bedienungsanleitung

Philips

Philips hue 24 po Bedienungsanleitung

Philips

Philips HP8550 Bedienungsanleitung

Philips

Philips bodine B30 Bedienungsanleitung

Philips

Philips CR434B Bedienungsanleitung

Philips

Philips hue Lightstrip Plus Bedienungsanleitung

Philips

Philips BN012C Benutzerhandbuch

Philips

Philips hue 17457 V7 Series Bedienungsanleitung

Philips

Philips Selecon Fresco Bedienungsanleitung

Philips

Philips eW Cove QLX Powercore Bedienungsanleitung

Philips

Philips hue 17466 V7 Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung