Philips Bodine B54 Bedienungsanleitung

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

! IMPORTANT SAFEGUARDS ! WHEN USING ELECTRICAL EQUIPMENT, BASIC

SAFETY PRECAUTIONS SHOULD ALWAYS BE

FOLLOWED, INCLUDING THE FOLLOWING:

SAVE THESE INSTRUCTIONS

THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.

THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.

A Division of Philips Electronics North America Corporation

236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.philips.com/bodine

75000400

FLUORESCENT EMERGENCY BALLAST

1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter

connector must be open. Do not join inverter connector until installation is complete and AC power is

supplied to the emergency ballast.

2. This product is for use with most 16 W through 40 W (2' -4') T8, T9, T10, or T12 (including T12 HO)

uorescent lamps, 18 W through 28 W (4-pin) twin, quad, and triple twin-tube, and 18 W through 39 W

rapid-start long compact lamps.

3. Make sure all connections are in accordance with the National Electrical Code and any local regulations.

4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and

inverter connector of the emergency ballast before servicing.

5. This emergency ballast is for factory or eld installation in either the ballast channel or on top of the

xture.

6. This product is for use in indoor xtures except air handling heated air outlets, and wet, damp, or

hazardous locations.

7. An unswitched AC power source is required (120 or 277 VAC, 60 Hz).

8. Do not install near gas or electric heaters.

9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not eld

replaceable. Contact the manufacturer for information on service.

10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.

11. Do not use this product for other than intended use.

12. Servicing should be performed by qualied service personnel.

09/14/09

B54

Ni - Cd

Installation Instructions

4 HOUR EMERGENCY OPERATION

INSTALLATION

WARNING: TO PREVENT HIGH VOLTAGE FROM BEING PRESENT ON RED & YELLOW OUTPUT

LEADS PRIOR TO INSTALLATION, INVERTER CONNECTOR MUST BE OPEN. DO NOT JOIN

INVERTER CONNECTOR UNTIL INSTALLATION IS COMPLETE AND AC POWER IS SUPPLIED TO

THE EMERGENCY BALLAST.

NOTE: Make sure the necessary branch circuit wiring is available. An unswitched source of

power is required. The emergency ballast must be fed from the same branch circuit

as the AC ballast.

STEP #1 INSTALLING THE EMERGENCY BALLAST

> Disconnect AC power from the xture. Remove the ballast channel cover and install the emergency ballast either

in the ballast channel or on top of the xture.* Remote mounting distance must be less than half the maximum

remote mounting distance for the AC ballast. Consult AC ballast manufacturer before remote installation.

> Depending on the type of xture in use install emergency ballast using one of the methods illustrated below.

STEP #2 INSTALLING THE TEST SWITCH

> Refer to the illustrations above and install the test switch

through the ballast channel cover of a troffer or through the

side of a strip xture.

> Drill a 1/2" hole and install the switch as shown.

> Refer to the diagrams below and wire the test switch so that

it removes AC power from both the emergency ballast and the

AC ballast at the same time.

* For installation on top of the xture, wire bundle covers (RMC-60) may be required by state or local codes. These covers are

available from the manufacturer as an accessory kit and must be ordered separately. Call your local distributor or the factory for complete

information.

Inside Ballast Channel Inside Strip Fixture On Top of Fixture

INSIDE BALLAST CHANNEL INSIDE STRIP FIXTURE ON TOP OF FIXTURE

UNSWITCHED FIXTURE SWITCHED FIXTURE

BLACK 120V

ORANGE 277V

BLACK AC

BALLAST

EMERGENCY

BALLAST

WHITE

BLK

HOT

COM

RED

(CAP UNUSED LEAD)

BLK

WALL

SWITCH

BLACK 120V

ORANGE 277V

BLACK AC

BALLAST

EMERGENCY

BALLAST

WHITE

BLK

HOT

COM

RED RED

(CAP UNUSED LEAD)

DOUBLE POLE

TEST SWITCH

BLK

DOUBLE POLE

TEST SWITCH

INSTALLATION

When AC power is applied, the charging indicator light is illuminated, indicating that the battery is being charged. When

power fails, the emergency ballast automatically switches to emergency power (internal battery), operating one lamp at

reduced illumination. This emergency ballast will operate 16 W through 40 W lamps for a minimum of 4 hours.

Although no routine maintenance is required to keep the emergency ballast functional, it should be checked periodically to

ensure that it is working. The following schedule is recommended:

1. Visually inspect the charging indicator light monthly. It should be illuminated.

2. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds. One lamp should

operate at reduced illumination.

3. Conduct a 90-minute discharge test once a year. One lamp should operate at reduced illumination for a

minimum of 4 hours.

! REFER ANY SERVICING INDICATED BY THESE CHECKS TO QUALIFIED PERSONNEL !

OPERATION

STEP #4 WIRING THE EMERGENCY BALLAST

> Determine the type of AC ballast installed in the xture.

> Select the appropriate wiring diagram on back to connect the emergency ballast to the AC ballast and lamp(s).

Make sure all connections are in accordance with the National Electrical Code and any local regulations.

> After installation is complete, supply AC power to the emergency ballast and join the inverter connector.

> At this point, power should be connected to both the AC ballast and the emergency ballast, and the Charging

Indicator Light should illuminate indicating the battery is charging.

> A short-term discharge test may be conducted after the emergency ballast has been charging for one hour. Charge

for 24 hours before conducting a long-term discharge test. Refer to OPERATION.

> In a readily visible location, attach the label "CAUTION - This Unit Has More Than One Power Connection Point.

To Reduce The Risk Of Electric Shock, Disconnect Both The Branch Circuit-Breakers Or Fuses And Emergency

Power Supplies Before Servicing."

MAINTENANCE

STEP #3 INSTALLING THE CHARGING INDICATOR LIGHT

> Install the CHARGING INDICATOR LIGHT as shown in the illustration below so that it will be visible after the

xture is installed.

NOTE: After installing the charging indicator light and test switch, mark each with the appropriate label.

TROFFER STYLE FIXTURE STRIP STYLE FIXTURE

Charging

Indicator

Light

1/2" White

Bushing

Violet (+)

Brown (–)

Violet (+)

Brown (–)

1/2" White

Bushing

5/8" Black

Bushing

5/8" Black

Bushing

1/2" Punch

Fixture Fixture

Charging

Indicator

Light

FIG 2a ONE (1) LAMP RAPID START BALLAST

FIG 52a ONE (1) LAMP INSTANT START BALLAST

WIRING DIAGRAM for 1-LAMP emergency operation

EMERGENCY BALLAST AND AC BALLAST MUST BE FED FROM THE SAME BRANCH CIRCUIT

TYPICAL SCHEMATICS ONLY. MAY BE USED WITH OTHER BALLASTS. CONSULT THE FACTORY FOR OTHER WIRING DIAGRAMS.

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP

BLACK

WHITE

RED

LINE BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

BLUE

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

BLACK

WHITE

LINE

RED

BLUE

BALLAST

LAMP

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

FIG 36a TWO (2) LAMP INSTANT START BALLAST FIG 3a TWO (2) LAMP RAPID START BALLAST

FIG 7a THREE (3) LAMP INSTANT START BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2 (EMERGENCY)

BLACK

WHITE

LINE BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST RED

BLUE

FIG 15a THREE (3) LAMP RAPID START BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

( )

EMERGENCY

LAMP 1

LAMP 2

BLACK

WHITE

YELLOW

LINE

RED

BLUE

BALLAST

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

FIG 1a ONE (1) 16-40 W LAMP WITHOUT AC BALLAST

WIRING DIAGRAMS for Emergency-Only xtures

FIG 14a FOUR (4) LAMP INSTANT START BALLAST FIG 51a FOUR (4) LAMP RAPID START BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2

LAMP 3

LAMP 4( )

EMERGENCY

BLACK

WHITE

YELLOW

LINE

RED

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

BLUE

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2

LAMP 3

LAMP 4

BLACK

WHITE

YELLOW

BROWN

LINE RED

RED

BLUE/WHT

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2

LAMP 3

BLACK

WHITE

LINE

RED

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

BLUE

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP 1

LAMP 2

LAMP 3( )

EMERGENCY

BLACK

WHITE

YELLOW

LINE

RED

BLUE/WHT

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

BALLAST

INVERTER

CONNECTOR

RED WHITE

ORANGE

BLACK

WHITE

VIOLET

BROWN

277 V

120 V

COM

CHARGING

INDICATOR

LIGHT

TO UNSWITCHED AC

USE PROPER TAP

CAP UNUSED LEAD

EMERGENCY

BALLAST

LAMP

BLUE

BLUE/WHT

YELL/BLK

YELLOW

RED

CAP

Inhaltsverzeichnis

Andere Philips Beleuchtungsausrüstung Handbücher

Philips

Philips HUE GO Bedienungsanleitung

Philips

Philips 56432-31-16 Bedienungsanleitung

Philips

Philips BN012C Benutzerhandbuch

Philips

Philips LED Luminaires Bedienungsanleitung

Philips

Philips hue 17457 V7 Series Bedienungsanleitung

Philips

Philips 56494-31-16 Bedienungsanleitung

Philips

Philips PLFRESNEL 1 LED LUMINAIRES Bedienungsanleitung

Philips

Philips hue Bedienungsanleitung

Philips

Philips Selecon Fresco Bedienungsanleitung

Philips

Philips Lightolier SV5 Bedienungsanleitung

Philips

Philips 40801 U7 Series Bedienungsanleitung

Philips

Philips Softone 871150066257610 Bedienungsanleitung

Philips

Philips 3222 623 87451 Bedienungsanleitung

Philips

Philips burton SUPER EXAM 50 LED Technisches Datenblatt

Philips

Philips 100LT Bedienungsanleitung

Philips

Philips Ecomoods 57940/31/96 Bedienungsanleitung

Philips

Philips 56493-31-16 Bedienungsanleitung

Philips

Philips Halogen MR16 Bedienungsanleitung

Philips

Philips RCH20 Bedienungsanleitung

Philips

Philips Lightolier Lytespan 23C39T4 Bedienungsanleitung

Philips

Philips 30504 Bedienungsanleitung

Philips

Philips CR434B Bedienungsanleitung

Philips

Philips 32158-31-16 Bedienungsanleitung

Philips

Philips Lightolier Solution Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung