Philips LEDALITE TruGroove Series Bedienungsanleitung

ATTENTION: Install in accordance with national and local building and electrical codes.

! Page 1

Mount Spacing & Power Feed Location

TruGroove Perimeter modules are designed for exact on-grid mounting. 2 mount-

ing and 2 power feed locations are available on each module. Refer to layout draw-

ings or row configuration documents for module lengths and mounting distances.

On Grid End Set

 On-grid endplate left (x1)

 On-grid endplate right (x1)

 #8 sheet metal screws (x6)

System Overview

These instructions review how to install TruGroove Perimeter Ambient and Graze fixtures. Modules can be installed as individual

standalone units, or they can be joined together to create continuous runs. The graphics below show the components required to

install a typical run of TruGroove Perimeter fixtures. IMPORTANT: Read all instructions before beginning installation.

Tools Required:

Grid Panel Kit

 Grid panel (x1)

 Grid clips (x2)

 #8 sheet metal screws (x3)

Joiner Kit

 Joiner bracket (x1)

 Biscuit aligners (x2)

 #8 sheet metal screws (x2) Variable End Set

 Variable endplate left (x1)

 Variable endplate right (x1)

 Variable panels (x2)

 On-grid end caps (x2)

 Grid clips (x2)

 #8 sheet metal screws (x8)

 Phillips Screwdriver  #2 Robertson Screwdriver

Wall Rail

ATTENTION: Install in accordance with national and local building and electrical codes.

! Page 2

Ceiling preparation covers grid ceiling modifica-

tions, attachment of wall rails and mount installation.

Above diagram covers all required dimensions for

standard t-grid installation. IMPORTANT: Grid

opening size must be followed for proper fit.

Ceiling Preparation

(Flat Wall) 1b

Optional: Textured walls. Above diagram covers all

required dimensions for standard t-grid installation

with a textured wall. IMPORTANT: To ensure a

proper fit, blocking (by others) must be the same

thickness as wall texture.

Ceiling Preparation

(Textured Wall) 2a

TruGroove perimeter fixture modules are available

in two different above plenum heights. Refer to

layout drawings for required regress. Standard 4”

regress is shown in above diagram. Attach wall rails

(hardware by others) to wall studs at specified

height. IMPORTANT: Ensure all wall rails are level.

Wall Rail Installation 4” Regress 2b

Optional 2” regress is shown in above diagram.

Attach wall rails (hardware by others) to wall studs

at specified height. IMPORTANT: Ensure all wall

rails are level.

Wall Rail Installation 2” Regress

Refer to page 1 and steps 1a/1b above for determin-

ing mounting locations. To install the 1st module,

two brackets and suspension cables are required.

When joining luminaires, only one bracket and sus-

pension cable are required for each joining module.

Mount Installation 4

Determine required power feel locations. Refer to

page 1 for typical power feed locations for each

housing. Prepare power feed drop conduit and

suspend close to required location. Attachment to

fixture module is shown in step 8.

Power Feed Preparation 5

Lift fixture module past ceiling plane, Tilt as shown

and engage housing hook on wall rail.

Fixture Installation 6a

Insert suspension cables installed in step 3 through

cable grippers inside fixture housing. IMPORTANT:

Ensure suspension cables are vertical. Level fixture

and trim excess cable to 1” below fixture. Tuck

remaining cable inside fixture housing.

Fixture Installation

Electrical conduit

(by others)

Aach bracket to structure

(hardware by others)

Flat

wall

shown

Flat

wall

shown

Suspension

cable

Wall rail

Suspension

cable

Wall rail

Suspension

cable

Ceiling bracket

Hook

Ambient shown

Boom

edge of

installed

xture

ATTENTION: Install in accordance with national and local building and electrical codes.

! Page 3

Break 7/8” knockout at end of housing at required

power feed location. Install conduit connector (by

others) and complete electrical connections. For a

row end, tuck wires inside wiring cavity and follow

endplate installation instructions starting in step 13.

Power Feed Connection 9

Slide dimpled side of joiner bracket approximately 1

inch inside top channel of module 1. Tap biscuit

aligners just past half way inside module 2 as shown.

Fixture Joining

10 Fixture Joining 11

IMPORTANT: Before sliding fixtures together, make

sure all electrical wires and suspension cables are

properly tucked inside fixture wiring cavities. Slide

fixture housings together and attach second joiner

bracket screw.

Fixture Joining 13

Secure endplate to housing with 3 screws as shown.

Flat End Installation

Secure joiner bracket to module 1 with screw pro-

vided. Slide module 2 on rail and engage on free end

of joiner bracket. Complete all required electrical

connections and tuck all wires inside both wiring

cavities.

Engage housing on wall rail. Insert suspension cables

installed in step 3 through cable grippers inside fix-

ture housing. Pull cables through and refer to next

step for levelling. IMPORTANT: Remove graze pack-

aging insert from both ends of each housing.

Fixture Installation 7

To adjust fixture level, support bottom of housing

and release cable gripper by pulling tab as shown.

Cable will slide freely and allow fine tuning of housing

position. Repeat process at each cable gripper loca-

tion using same procedure to ensure housing is level.

Fixture Installation

For variable end installation, skip to step 14b.

Rotate and position bottom of endplate inside grid

and push flat against housing end.

Flat End Installation

Remove

packaging

insert

5⁰ max. cable

deviaon

from vercal

Release tab

Graze shown Graze shown

ATTENTION: Install in accordance with national and local building and electrical codes.

! Page 4

14a

IMPORTANT: Flat endplate must be oriented and

installed as shown above. If variable ends are not

required, skip to step 17 for panel installation.

Flat End Installation 14b

After fixture modules have been installed and lev-

elled, measure distance between wall and fixture end.

Trim variable endplate as required. INSTALLATION

TIP: Before next step, attach 2 screws shown above

to housing. Fully tighten then back off 1/2 turn.

Variable End Installation 15

After variable endplate has been trimmed to size,

slide endplate toward wall guiding open slots to-

wards screws installed in step 14b. Hook slots on

screws and push all the way towards wall.

Variable End Installation

NOTE: Installed at

endplate orientaon

Check that endplate edge is flush with housing and

attach final screw to lock in place.

Variable End Installation

Insert grid clips (x2) to grid panel at slot locations.

Push grid clip up as shown until bottom of clip is

flush with bottom of grid panel.

Panel Installation 19 Panel Installation 20

Secure grid panel to housing by attaching provided

screws to housing through panel slots as shown.

Repeat panel installation to complete run.

Panel Installation

Before installing grid panels, all panels ending on grid

must be trimmed as shown. Ensure one left and

one right are trimmed for each required run.

Panel Installation –On Grid

Starting at one end, align first grid panel with end of

housing and slide onto t-grid to engage clips.

Trim endplate

as needed

Trim at

grid end

Grid panel

ATTENTION: Install in accordance with national and local building and electrical codes.

! Page 5

For variable ends at a wall, insert variable panel

inside installed grid panel. Slide to required posi-

tion. NOTE: When installed, the variable panel

will match the length of variable endplate installed

in steps 14b-16 .

Variable Panel Installation 23

Secure variable panel to housing with screw

provided.

Variable Panel Installation 24

 Ensure all fixtures are level and in line

with each other.

 Check that all joint and endplate screws

are installed and all seams are tight.

 Check that all panel screws are attached

and tight.

For variable ends on-grid, insert variable panel

inside installed grid panel.

Variable Panel Installation

Wall

(not shown for clarity)

Wall

(not shown for clarity)

Secure grid clips to t-bar ceiling using screws

(by others).

Panel Installation

Attach on-grid endplate by securing grid clip to

t-bar. Secure grid clip to t-bar following

instructions shown in step 21.

Variable End Installation 27 Variable Panel Installation 28

Finishing

Install grid clip to on-grid end cap by following

instructions shown in step 18.

Variable End Installation

Slide variable panel against t-bar and secure to

housing with screw provided.

Oponal

Oponal Oponal Oponal

Inhaltsverzeichnis

Andere Philips Beleuchtungsausrüstung Handbücher

Philips

Philips GreenPower LED production module DR/B Bedienungsanleitung

Philips

Philips Showline SL eSTROBE 130 Bedienungsanleitung

Philips

Philips B50 Bedienungsanleitung

Philips

Philips Ecomoods 16902/**/16 Bedienungsanleitung

Philips

Philips hue 17457 V7 Series Bedienungsanleitung

Philips

Philips LED Luminaires Bedienungsanleitung

Philips

Philips BVP528 Bedienungsanleitung

Philips

Philips 56459-17-16 Bedienungsanleitung

Philips

Philips Lightolier SQ6-3 Bedienungsanleitung

Philips

Philips 32158-31-16 Bedienungsanleitung

Philips

Philips RCH20 Bedienungsanleitung

Philips

Philips 57945-17-16 Bedienungsanleitung

Philips

Philips hue Bedienungsanleitung

Philips

Philips CR434B Bedienungsanleitung

Philips

Philips HUE GO Bedienungsanleitung

Philips

Philips Fluorescent Lamps Bedienungsanleitung

Philips

Philips 57947-17-16 Bedienungsanleitung

Philips

Philips HF3532 Bedienungsanleitung

Philips

Philips Stylid Evo Compact Bedienungsanleitung

Philips

Philips ELC/10H Long Life Bedienungsanleitung

Philips

Philips Illuminate Bedienungsanleitung

Philips

Philips Lightolier Lytespan 23C39T4 Bedienungsanleitung

Philips

Philips Lightolier EG1-4 Bedienungsanleitung

Philips

Philips InteGrade LED engine system Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung