Philips 7000 Setie Bedienungsanleitung

Party Speaker

7000 Series

TAX7207

User manual

www.philips.com/support

2 3ENEN

Contents

1 Important safety instructions 3

Safety 3

Care for your product 4

Care of the environment 4

Declaration of conformity 4

Help and support 4

Hearing safety 5

Built-in battery care 5

Trademarks 5

2 Your party speaker 7

What’s in the box 7

Party speaker 8

3 Get started 9

Connect to power 9

Turn On and O 10

Volume control 10

DBB control 10

Charge the built-in battery 10

Change light eect 11

Play from Bluetooth devices 12

Pairing for stereo mode (TWS) 13

PartyLink mode 14

Play audio through USB 15

Listen to an external device 16

Sing through microphone 16

Factory reset 16

Update rmware via USB 17

Pole-mounting your party speaker 17

4 Product specications 18

5 Troubleshooting 19

2 3ENEN

1 Important

safety

instructions

Read and understand all instructions

before you use your product. If damage

is caused by failure to follow instructions,

the warranty does not apply.

Safety

Know these safety symbols

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This is CLASS II apparatus with

double insulation, and no

protective earth provided.

AC voltage

Use only the power supplies listed

in the user manual.

WARNING!

Warning: Risk of electric shock!

The exclamatory mark is intended

to alert the user of the presence of

important operating instructions.

Risk of electric shock or re!

• Before you make or change any

connections, make sure that all

devices are disconnected from the

power outlet.

• Never expose the product and

accessories to rain or water. Never

place liquid containers, such as vases,

near the product. If liquids are spilt

on or into the product, disconnect it

from the power outlet immediately.

Contact Consumer Care to have the

product checked before use.

• Never place the product and accessories

near naked ames or other heat sources,

including direct sunlight.

• Never insert objects into the

ventilation slots or other openings

on the product.

• Where the mains plug or an

appliance coupler is used as the

disconnect device, the disconnect

device shall remain readily operable.

• Disconnect the product from the

power outlet before lightning storms.

• When you disconnect the power cord,

always pull the plug, never the cable.

• Use the product in tropical and/or

moderate climates.

Risk of short circuit or re!

• For identication and supply ratings,

see the type plate at the back or

bottom of the product.

• Before you connect the product to

the power outlet, ensure that the

power voltage matches the value

printed on the back or bottom of the

product. Never connect the product

to the power outlet if the voltage is

dierent.

Risk of injury or damage to this

product!

• For wall mounting, this product must

be securely attached to the wall in

accordance with the installation

instructions. Use only the supplied

wall mount bracket (if available).

Improper wall mounting may result

in accident, injury or damage. If you

have any query, contact Consumer

Care in your country.

• Never place the product or any

objects on power cords or on other

electrical equipment.

4 5ENEN

Inform yourself about the local separate

collection system for electrical and

electronic products and batteries.

Follow local rules and never dispose of

the product and batteries with normal

household waste. Correct disposal

of old products and batteries helps

prevent negative consequences for the

environment and human health.

Declaration of conformity

This product complies with the radio

interference requirements of the

European community.

Hereby, MMD Hong Kong Holding

Limited declares that the product

is in compliance with the essential

requirements and other relevant

provisions of RED Directive 2014/53/EU

and UK Radio Equipment Regulations

SI 2017 No 1206. You can nd the

Declaration of Conformity on www.

philips.com/support.

Help and support

For extensive online support, visit www.

philips.com/support to:

• download the user manual and the

quick start guide

• watch video tutorials (available only

for selected models)

• nd answers to frequently answered

questions (FAQs)

• email us a question

• chat with our support representative.

Follow the instructions on the website

to select your language, and then enter

your product model number.

Alternatively, you can contact Consumer

Care in your country. Before you contact,

note down the model number and serial

number of your product. You can nd

this information on the back or bottom

of your product.

• If the product is transported in

temperatures below 5°C, unpack

the product and wait until its

temperature matches room

temperature before connecting it to

the power outlet.

• Parts of this product can be made

of glass. Handle with care to avoid

injury and damage.

Risk of overheating!

• Never install this product in a

conned space. Always leave a

space of at least four inches around

the product for ventilation. Ensure

curtains or other objects never cover

the ventilation slots on the product.

Note

• The rating label is pasted on the bottom or back

of the equipment.

Care for your product

Use only microber cloth to clean the

product.

Care of the environment

Disposal of your old product and

battery

Your product is designed and

manufactured with high quality

materials and components, which

can be recycled and reused.

This symbol on a product means

that the product is covered by

European Directive 2012/19/EU.

This symbol means that the product

contains batteries covered by

European Directive 2013/56/EU

which cannot be disposed of with

normal household waste.

4 5ENEN

Hearing safety

Listen at a moderate volume

• Using headphones at a high volume

can impair your hearing. This product

can produce sounds in decibel ranges

that may cause hearing loss for a

normal person, even for exposure

less than a minute. The higher

decibel ranges are oered for those

that may have already experienced

some hearing loss.

• Sound can be deceiving. Over time

your hearing ‘comfort level’ adapts

to higher volumes of sound. So after

prolonged listening, what sounds

‘normal’ can actually be loud and

harmful to your hearing. To guard

against this, set your volume to a

safe level before your hearing adapts

and leave it there.

To establish a safe volume level

• Set your volume control at a low

setting.

• Slowly increase the sound until you

can hear it comfortably and clearly

without distortion.

Listen for reasonable periods of time

• Prolonged exposure to sound, even

at normally safe levels, can also cause

hearing loss.

• Be sure to use your equipment

reasonably and take appropriate

breaks.

• Be sure to observe the following

guidelines when using your

headphones.

• Listen at reasonable volumes for

reasonable periods of time.

• Be careful not to adjust the volume

as your hearing adapts.

• Do not turn up the volume so high

that you can’t hear what’s around you.

• You should use caution or

temporarily discontinue use in

potentially hazardous situations.

Built-in battery care

• The battery can be charged and

discharged hundreds of times, but

will eventually wear out.

• If left unused, a fully charged battery

will lose its charge over time.

• Leaving the product in hot or cold

places, such as in a closed car in the

summer and winter conditions, will

reduce the capacity and lifetime of

the battery.

• Always try to keep your device in

a cool, moisture-free environment

that’s less than 32°C. A product with

a hot or cold battery may not work

temporarily, even when the battery is

fully charged. Battery performance is

particularly limited in temperatures

well below freezing.

Trademarks

The Bluetooth® word mark and logos

are registered trademarks owned

by Bluetooth SIG, Inc. and any use

of such marks by MMD Hong Kong

Holding Limited is under license. Other

trademarks and trade names are those of

their respective owners.

67ENEN

IC-Canada:

CAN ICES-003(B)/NMB-003(B)

This device contains licence-exempt

transmitter(s) / receiver(s) that comply

with Innovation, Science and Economic

Development Canada’s licence-exempt

RSS(s). Operation is subject to the

following two conditions:

1 This device may not cause

interference.

2 This device must accept any

interference, including interference

that may cause undesired operation

of the device.

Avis d’Industrie Canada:

CAN ICES-003(B)/NMB-003(B)

L’émetteur/récepteur exempt de licence

contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences

et Développement économique Canada

applicables aux appareils radio exempts

de licence. L’exploitation est autorisée

aux deux conditions suivantes :

1 L’appareil ne doit pas produire de

brouillage ;

2 L’appareil doit accepter tout

brouillage radioélectrique

subi, même si le brouillage est

susceptible d’en compromettre le

fonctionnement.

FCC information

NOTE: This equipment has been tested

and found to comply with the limits

for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits

are designed to provide reasonable

protection against harmful interference

in a residential installation. This

equipment generates, uses and can

radiate radio frequency energy and, if

not installed and used in accordance

with the instructions, may cause harmful

interference to radio communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does

cause harmful interference to radio

or television reception, which can be

determined by turning the equipment

o and on, the user is encouraged to

try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an

outlet on a circuit dierent from that

to which the receiver is connected.

• Consult the dealer or an experienced

radio / TV technician for help.

FCC&IC Warning:

• This equipment should be installed

and operated with minimum

distance 20cm between the radiator

and your body.

• Changes or modications to this unit

not expressly approved by the party

responsible for compliance could

void the user’s authority to operate

the equipment.

67ENEN

2 Your party

speaker

Congratulations on your purchase, and

welcome to Philips! To fully benet from

the support that Philips oers, register your

party speaker at www.philips.com/support.

What’s in the box

Check and identify the items in the

package:

Party Speaker x 1

Power Cord * x 1

• Power cord quantity and plug type

vary by regions.

TAX7207/93 TAX7207/37 TAX7207/10 TAX7207/98 TAX7207/94

for China

CCCVDEBS

for Europe/UK

for US/Canada

VDEBSSAA

for Asia

BIS

for India

TAX7207/70

SNI

for Indonesia

TAX7207/67

TISI

for Thailand

Headph ones

hon

Headph ones

Series

CTN

Safety Information

Quick Start Guide x 1

Headph ones

hon

Headph ones

Series

CTN

Safety Information

Warranty Card x 1

Headph ones

hon

Headph ones

Series

CTN

Safety Information

Safety Sheet x 1

• Images, illustrations and drawings

shown on this user manual are for

reference only, actual product may

vary in appearance.

8 9ENEN

Party speaker

This section includes an overview of the

party speaker.

1 2 3 4 5

14 15 16 17 18 19

910 11 12 13

a (Light) touch key

• Press to change speaker light

mode.

• Press and hold for 3 seconds to

change speaker light brightness.

b DBB touch key

BASS eect setup.

c +/－ (Volume) touch key

Increase/Decrease the volume.

d (Play/Pause) touch key

• Start, pause or resume play.

• Press and hold to skip to next

track.

e (Standby-On) touch key

• Press and hold for 3 seconds to

switch on/o the unit.

• Press to check battery level in

power on status.

f Speaker light

1 2 3 4 5

14 15 16 17 18 19

910 11 12 13

Button Status

Short press

Light mode 1

Light o

g LED indicator

• Battery level indicator

• Function status

LED Function Color

LED1 DBB Solid yellow

LED2 Standby Solid red

Vocal fader Solid white

LED3

Bluetooth Blink or solid blue

TWS pairing Blink blue-white

PartyLink connected Solid white

LED4 Voice changer Solid green

PartyLink pairing Blink green-white

h Vocal fader button

Press repeatedly to switch between

vocal fader on and vocal fader o.

8 9ENEN

i Voice changer button

Press repeatedly to switch among

dierent voice tones: Woman voice/

Man voice/Children voice/Normal eect.

j PartyLink button

Press to enter PartyLink pairing

mode.

k TWS pair button

• Press to enter True Wireless

Stereo (TWS) pairing mode.

• It work only when you have two

identical speakers.

l Bluetooth / pair button

• Switch to Bluetooth mode.

• Press and hold to activate the

pairing function in Bluetooth

mode or disconnect the existing

paired Bluetooth device.

m Mic1 in / Mic2 in socket

Connect a microphone (not supplied)

into the Mic1 in / Mic2 in socket on

the unit.

n Mic1 vol +/－Knob

Adjust microphone volume.

o Mic2 vol +/－Knob

Adjust microphone volume.

p Echo +/－Knob

Adjust the microphone echo level.

q USB (5V, 0.5A) socket

• Insert the USB device to play music.

• Upgrade software of this product.

r Audio in socket

Audio input from, for example, an

MP3 player (3.5mm socket).

s Audio out socket

Connect an audio cable (not

supplied) to the Audio out socket on

the unit and the audio in socket of

the external device, and the unit will

output audio automatically to the

external device.

t AC in~ socket

Connect to the power supply.

3 Get started

When you use this unit for the rst time

or unused for long periods of time,

recharge the battery fully.

Note

• For identication and supply ratings, see the

type plate at the back or bottom of the product.

• Before you make or change any connections,

make sure that all devices are disconnected

from the power outlet.

Connect to power

WARNING!

• Risk of product damage! Make sure that the

power supply voltage corresponds to the

voltage printed on the back or the underside of

the product.

• Risk of electric shock! When you unplug the

power cord, always pull the plug from the

socket. Never pull the cord.

• Before connecting the AC power cord, ensure

you have completed all other connections.

Connect the mains cable to the AC in~

socket of the party speaker and then into

a mains socket.

AC in ~

Power cord quantity and plug type vary

by regions.

10 11ENEN

Turn On and O

Press and hold touch key for 3 seconds

to switch on/o the unit.

Note

• The speaker will turn o automatically after

15 minutes without user operations and music

playback.

• In case of no response of button or function

error, you can press and hold Vocal fader and

buttons for 10 seconds to force shutdown, then

turn on the unit again to be used normally.

Volume control

Press +/－touch key to increase or

decrease volume level.

Tip

• While adjusting the volume, the white speaker

light will move up or down for 3 seconds.

• When the volume meets the maximum level,

the white speaker light will fully turn on for 3

seconds.

• When the volume meets the minimum level, the

white speaker light will turn o for 3 seconds.

DBB control

Short press DBB touch key to switch the

DBB (bass) level.

Function LED1 (Yellow)

DBB1 LED1 ash once then solid

DBB2 LED1 ash twice then solid

DBB o LED1 o

Charge the built-in

battery

Plug the AC power cord to charge the

built-in battery. The battery indicators

blink in dierent manners to indicate the

charging status.

Note

• The four indicators on the unit will go out in 15

seconds after the battery is fully charged.

20%

100

50%

80%

100

20%

Low Battery

50%

80%

100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Philips Sprecher Handbücher

Philips

Philips BT2500 Produktinformationsblatt

Philips

Philips HTL6145C Bedienungsanleitung

Philips

Philips Fidelio HTL7180 Bedienungsanleitung

Philips

Philips HTL2151 Bedienungsanleitung

Philips

Philips DSS 350 Bedienungsanleitung

Philips

Philips TAS4405N Bedienungsanleitung

Philips

Philips AD7000W/10 Bedienungsanleitung

Philips

Philips SPA6270BT Bedienungsanleitung

Philips

Philips HTS7140 Bedienungsanleitung

Philips

Philips HTL7140B Bedienungsanleitung

Philips

Philips SPA1305/10 Bedienungsanleitung

Philips

Philips CSP410 Bedienungsanleitung

Philips

Philips SPA3210B/10 Bedienungsanleitung

Philips

Philips HTL2101A/96 Bedienungsanleitung

Philips

Philips SPA7355 Bedienungsanleitung

Philips

Philips Fidelio DS3880W/10 Bedienungsanleitung

Philips

Philips BT100 Produktinformationsblatt

Philips

Philips Fidelio AD7050W Bedienungsanleitung

Philips

Philips S4405 Bedienungsanleitung

Philips

Philips HTL1100 Bedienungsanleitung

Philips

Philips BT6000A/94 Bedienungsanleitung

Philips

Philips SPA1302/05 Bedienungsanleitung

Philips

Philips HTL2100 Bedienungsanleitung

Philips

Philips HTL6140B Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung