Phocos Any-Grid Series Bedienungsanleitung

Phocos Any-Grid™ series

Any-Grid™ PSW-H use with lithium battery models:

Hubble AM-2, AM-4, X-100 and X-101

Applicable for Any-Grid™ models

48 Vdc: PSW-H-5kW-230/48V, PSW-H-5kW-120/48V,

PSW-H-6.5kW-120/48V

24 Vdc: PSW-H-3KW-230/24V and

PSW-H-3KW-120/24V

Setup guide

www.phocos.com 1 | P a g e

1.0 Introduction

This guide outlines the recommended settings and establishing communication for operation of one or more Any-

Grid™ PSW-H-5kW-230/48V, PSW-H-5kW-120/48V or PSW-H-6.5kW-120/48V hybrid inverter chargers with Hubble

AM-2, X-100 and X-101 battery units, referred to in this guide as “battery units”. PSW-H-3KW-230/24V and PSW-H-

3KW-120/24V are only compatible with the Hubble AM-4 battery units. All connected batteries must be of the same

model name.

Note that the charge/discharge settings are automatically negotiated with the battery if this guide is used and do

not need to be changed.

The Any-Grid must be installed according to the Any-Grid PSW-H “User and Installation Manual” included with every

Any-Grid PSW-H unit and available online at www.phocos.com. The battery terminals of the Any-Grid must be

connected to the battery units according to the Hubble installation manual at the appropriate step mentioned in the

chapter 5.0 of this manual.

WARNING: Be sure to read and respect the warnings in the installation manuals of the Any-Grid, the battery units and any other connected equipment. The installation must be conducted by a trained professional.

2.0 Requirements

The following is required to proceed with this guide:

•48 Vdc battery: Any-Grid PSW-H-5KW-230/48V, PSW-H-5KW-120/48V or PSW-H-6.5KW-120/48V

24 Vdc battery: Any-Grid PSW-H-3KW-230/24V and PSW-H-3KW-120/24V

•Hubble Cloudlink device

•Hubble Cloudlink communication cable included with Cloudlink device (6-pin RJ-12 to 8-pin RJ-45

connectors):

WARNING: Make sure to use the correct battery to Any-Grid cable. Any damage to the PSW-H or battery due to incorrect wiring, cable orientation or use of an incorrect cable is not covered by any warranty.

•Hubble CAN Bus cable included with Cloudlink device:

•Hubble battery unit(s)

www.phocos.com 2 | P a g e

3.0 System Overview

4.0 Battery Sizing

To maintain the full battery warranty, each battery unit should be sized not to exceed 100 Adc continuous charge /

discharge current and 125 Adc peak for up to 100 ms. It is thus strongly recommended to use at least 1.5 battery

units in parallel to deliver both sufficient continuous current and peak current for a single PSW-H-5KW at full power.

Per PSW-H-6.5KW-120/48V use at least 2 battery units. Use at least 1.8 AM-4 battery units per PSW-H-3KW unit. Of

course, when using a single PSW-H at full power, this means using at least two battery units. Using fewer batteries per

inverter may void your Hubble battery warranty and disrupt service by the battery automatically disconnecting from

the Any-Grid(s).

The batteries must be wired in parallel to form a single large battery bank when using multiple Any-Grids. All Any-

Grids must be connected to a single battery array made up of a maximum of 15 battery units.

5.0 Battery Communication Cable Installation and Powering On

CAUTION: Before connecting the battery units to the Any-Grid(s), please follow the installation instructions in this chapter step by step. The battery, AC input source, AC output loads and PV input must remain disconnected until instructed otherwise.

1. Ensure the battery units are all turned off.

2. Set the address DIP switches on the battery units according to the battery manual (location circled below):

3. Ensure the battery units are still turned off. Connect the Any-Grid(s) to the battery power (positive and

negative) terminals with the correct polarity.

CAUTION: If the correct polarity of the battery is not observed, the Any-Grid and the battery may be damaged, this is not covered by warranty.

Plug the RJ-12 end of the battery communication cable into the Cloudlink device’s “S” port and the RJ-45 side

Hubble battery unit(s)

www.phocos.com 3 | P a g e

into the Any-Grid display panel’s “RS-232” port:

Any-Grid Cloudlink

For systems with multiple Any-Grids, this connection (marked red) can be made with any of the inverters,

but only a single unit. Remember, all Any-Grids in a synchronised system must be connected to a single

battery bank.

4. Using the provided RJ45 cable with the Cloudlink, plug in the CAN Bus cable into the “CAN” port of the

Hubble battery and the other end into the “CAN” port of the Cloudlink device.

5. Ensure the battery units are wired as outlined in the Hubble battery manual. Turn on each of the battery

units with the power button (circled below in red) and ensure the “RUN” LED blinks is green for all battery

units and that the “ALM” LED is turned off (circled below in green):

6. Turn the “ON/OFF” load power button of the Any-Grid(s) to the ON position (depressed), but make sure no

loads are connected:

The Any-Grid(s) should now be running, the display(s) on.

7. Please refer to the setup guide for the Cloudlink on the Hubble website for setup procedure of the Cloudlink

device at www.hubblelithium.co.za.

8. When the Cloudlink setup is complete, and if no errors are present on the Any-Grid(s) and any of the battery

unit(s), turn on the load breaker, followed by the PV and finally the AC source breaker (if present in the

system).

The commissioning battery unit(s) and Any-Grid(s) is now complete.

www.phocos.com 4 | P a g e

The content of this document is subject to change without notice.

Version: 20210916

Phocos AG

Magirus-Deutz-Str. 12

89077 Ulm, Germany

Phone +49 731 9380688-0

Fax +49 731 9380688-50

www.phocos.com

[email protected]

Andere Handbücher für Any-Grid Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Phocos Wechselrichter Handbücher

Phocos

Phocos LS Series Bedienungsanleitung

Phocos

Phocos Any-Grid Series Betriebsanleitung

Phocos

Phocos Any-Grid PSW-H-5kW-230/48V Gebrauchsanweisung

Phocos

Phocos Any-Grid PSW-H-8KW-230/48V Bedienungsanleitung

Phocos

Phocos MPPT100/30 Bedienungsanleitung

Phocos

Phocos CXup 10 Bedienungsanleitung

Phocos

Phocos SI700-24110 Bedienungsanleitung

Phocos

Phocos Any-Grid Series Betriebsanleitung

Phocos

Phocos ECO-N-MPPT 85/15 Bedienungsanleitung

Phocos

Phocos Any-Grid PSW-H-6.5kW-120/48V Bedienungsanleitung

Phocos

Phocos Any-Grid PSW-B-5KW-230/48V Betriebsanleitung

Phocos

Phocos CML05-2 Bedienungsanleitung

Phocos

Phocos CIS-N-MPPT-LED 85/15 Bedienungsanleitung

Phocos

Phocos SI700-12110 Bedienungsanleitung

Phocos

Phocos CXNup Bedienungsanleitung

Phocos

Phocos Any-Grid Series Service-Handbuch

Phocos

Phocos SI1500-24110 Bedienungsanleitung

Phocos

Phocos MPPT100/30 Bedienungsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

Astrel Group

Astrel Group Power Reducer Kurzanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung