Phytec PhyCORE-LPC3180 Bedienungsanleitung

phyCORE-LPC3180

HARDWARE MANUAL

EDITION APRIL 2007

A product of a PHYTEC Technology Holding company

phyCORE-LPC3180

©PHYTEC America LLC 2007 L-681e_3

In this manual are descriptions for copyrighted products that are not explicitly

indicated as such. The absence of the trademark (™) and copyright (©) symbols

does not imply that a product is not protected. Additionally, registered patents and

trademarks are similarly not expressly indicated in this manual.

The information in this document has been carefully checked and is believed to be

entirely reliable. However, PHYTEC America LLC assumes no responsibility for any

inaccuracies. PHYTEC America LLC neither gives any guarantee nor accepts any

liability whatsoever for consequential damages resulting from the use of this manual

or its associated product. PHYTEC America LLC reserves the right to alter the

information contained herein without prior notification and accepts no responsibility

for any damages which might result.

Additionally, PHYTEC America LLC offers no guarantee nor accepts any liability for

damages arising from the improper usage or improper installation of the hardware or

software. PHYTEC America LLC further reserves the right to alter the layout and/or

design of the hardware without prior notification and accepts no liability for doing so.

Rights - including those of translation, reprint, broadcast, photomechanical or similar

reproduction and storage or processing in computer systems, in whole or in part - are

reserved. No reproduction may occur without the express written consent from

PHYTEC America LLC.

EUROPE NORTH AMERICA

Address: PHYTEC Technologie Holding AG

Robert-Koch-Str. 39

D-55129 Mainz

GERMANY

PHYTEC America LLC

203 Parfitt Way SW, Suite G100

Bainbridge Island, WA 98110

USA

Ordering

Information: +49 (800) 0749832

[email protected]

1 (800) 278-9913

[email protected]

Technical

Support: +49 (6131) 9221-31

[email protected]

1 (800) 278-9913

[email protected]

Fax: +49 (6131) 9221-33 1 (206) 780-9135

Web Site: http://www.phytec.de http://www.phytec.com

3rd Edition April 2007

Contents

©PHYTEC America LLC 2007 L-681e_3

Preface ............................................................................................................ 1

1Introduction............................................................................................. 2

1.1 Block Diagram .................................................................................. 4

1.2 View of the phyCORE-LPC3180 ...................................................... 5

2Pin Description....................................................................................... 7

3Jumpers................................................................................................. 17

3.1 J503 MCKO Signal........................................................................ 23

3.2 J504 A/D Positive Supply/Reference Voltage ............................... 23

3.3 A/D Negative Supply/Reference Voltage........................................ 23

4Power Requirements............................................................................ 24

4.1 Real Time Clock and SRAM Battery .............................................. 24

4.1.1 Real Time Clock and SRAM Power Source (J506)............ 25

4.2 Voltage Supervision (U409)............................................................ 25

5System Configuration.......................................................................... 26

5.1 Boot Process .................................................................................. 26

5.2 Boot Modes..................................................................................... 29

6System Memory.................................................................................... 30

6.1 Memory Model................................................................................ 30

6.2 SDR SDRAM (U602, U603) ........................................................... 31

6.3 NAND Flash Memory (U600).......................................................... 31

6.3.1 NAND Flash Write Protection Control (J604)..................... 32

6.4 I²C EEPROM (U601) ...................................................................... 32

6.4.1 Setting the EEPROM Lower Address bits

(J600, J601, J602).............................................................. 33

6.4.2 EEPROM Write Protection Control (J603).......................... 33

7SIBL, U-Boot and Linux....................................................................... 34

8Serial Interfaces.................................................................................... 35

8.1 RS-232 Transceivers (U301, U302)............................................... 35

8.1.1 UART2 Routing Jumpers J300, J301, J302 and J303....... 35

8.2 USB Transceiver (U300)................................................................. 36

9Processor Independent Watchdog (U408)......................................... 37

9.1 Setting the Watchdog Timeout Period (J400)................................. 37

9.2 Interfacing the WDI Watchdog Input (J401) ................................... 38

10 Debug Interface X201........................................................................... 39

11 Technical Specifications ..................................................................... 42

12 Hints for Handling the phyCORE-LPC3180 ....................................... 44

phyCORE-LPC3180

©PHYTEC America LLC 2007 L-681e_3

13 The phyCORE-LPC3180 on the phyCORE-LPC3180 Carrier Board 45

13.1phyCORE-LPC3180 Carrier Board Peripherals ............................. 45

13.1.1 Jumpers on the phyCORE-LPC3180 Carrier Board........... 48

13.2Functional Components on the phyCORE-LPC3180

Carrier Board.................................................................................. 53

13.2.1 Power Supply at X304........................................................ 53

13.2.2 System Reset Button S300 ................................................ 53

13.2.3 Boot Selection using JP306................................................ 53

13.2.4 Accessing UART5 through Socket P300A ......................... 54

13.2.5 Accessing UART2 through Socket P300B ......................... 54

13.2.6 SD Card Interface at Connector X300................................ 55

13.2.7 User Buttons S302 and S303............................................. 56

13.2.8 User LEDs D400, D401, D402, and D403.......................... 56

13.2.9 Accessing the USB through Connectors X301, X302, and

X303.................................................................................... 57

13.2.10 A/D Potentiometer R313................................................. 57

13.2.11 Battery Connector BAT300............................................. 58

13.2.12 Power Connectors X306 and X307................................. 58

13.2.13 Keyboard Connector at X203.......................................... 59

13.2.14 Debug Interface X202..................................................... 60

13.2.15 Pin Assignment Summary of the phyCORE, the

Expansion Bus and the Patch Field.................................... 61

14 Revision History................................................................................... 71

15 Component Placement Diagram......................................................... 72

Appendix A ................................................................................................... 74

Index.............................................................................................................. 75

Contents

©PHYTEC America LLC 2007 L-681e_3

Index of Figures

Figure 1: Block Diagram phyCORE-LPC3180............................................... 4

Figure 2: Top View of the phyCORE-LPC3180 (controller side)................... 5

Figure 3: Bottom View of the phyCORE-LPC3180 (connector side)............. 6

Figure 4: Pinout of the phyCORE-Connector (Top View, with Cross

Section Insert) ................................................................................ 8

Figure 5: Numbering of the Jumper Pads.................................................... 17

Figure 6: Location of the Jumpers (Top View)............................................. 18

Figure 7: Location of the Jumpers (Bottom View) ....................................... 19

Figure 8: Default Jumper Settings on the phyCORE-LPC3180 (Top Side). 21

Figure 9: Default Jumper Settings on the phyCORE-LPC3180

(Bottom Side).....................................................................................

............................................................................................ 22

Figure 10: Small Page SLC NAND Flash Structure ...................................... 27

Figure 11: JTAG Interface X201 (Top View).................................................. 39

Figure 12: JTAG Interface X201 (Bottom View) ............................................ 40

Figure 13: Physical Dimensions .................................................................... 42

Figure 14: Component Locations on the phyCORE-LPC3180 Development

Board............................................................................................ 47

Figure 15: Typical Jumper Pad Numbering Scheme (solderless jumpers)... 48

Figure 16: Location of the Jumpers (View of the Component Side).............. 50

Figure 17: Default Jumper Settings of the phyCORE-LPC3180 Carrier

Board (J300, JP302-304) ............................................................. 51

Figure 18: Default Jumper Settings of the phyCORE-LPC3180 Carrier

Board (JP300-301, JP307-311, JP400-403)................................ 51

Figure 19: Default Jumper Settings of the phyCORE-LPC3180 Carrier

Board (JP305-JP306)................................................................... 52

Figure 20: Supply Voltage Connector Dimensions at X304 .......................... 53

Figure 21: Carrier Board Keyboard Connector X203 .................................... 59

Figure 22: Carrier Board JTAG Connector X202........................................... 60

Figure 23: Pin Assignment Scheme of the Expansion Bus X201.................. 61

phyCORE-LPC3180

©PHYTEC America LLC 2007 L-681e_3

Figure 24: Pin Assignment Scheme of the Patch Field on the Optional

GPIO Expansion Board................................................................ 62

Figure 25: phyCORE-LPC3180 Component Placement, Top View.............. 72

Figure 26: phyCORE-LPC3180 Component Placement, Bottom View......... 73

Contents

©PHYTEC America LLC 2007 L-681e_3

Index of Tables

Table 1: Pinout of the phyCORE-Connector X200....................................... 9

Table 2: Jumper Settings............................................................................ 20

Table 3: J503 MCKO Signal Configuration ................................................ 23

Table 4: J504, A/D Positive Supply/Reference Voltage Selection............. 23

Table 5: VBAT Operating Limits................................................................. 24

Table 6: J506 Real Time Clock and SRAM Power Source........................ 25

Table 7: LPC3180 Memory Map................................................................. 30

Table 8: Valid SDRAM Memory Address Ranges...................................... 31

Table 9: Compatible NAND Flash Devices ................................................ 31

Table 10: J604, EEPROM Write Protection States...................................... 32

Table 11: J600, J601, J602 EEPROM Lower Address Bits ........................ 33

Table 12: J603, EEPROM Write Protection States...................................... 33

Table 13: J300, J301, J302, J303 High Speed Serial Interface

Configuration ................................................................................ 36

Table 14: J400, Processor Independent Watchdog Timeout Period

Configuration ................................................................................ 37

Table 15: J401 First Serial Interface Configuration..................................... 38

Table 16: JTAG Connector X201 Signal Assignment .................................. 41

Table 17: Carrier Board Connectors............................................................. 45

Table 18: Carrier Board Buttons................................................................... 46

Table 19: Carrier Board LEDs...................................................................... 46

Table 20: Carrier Board Potentiometers....................................................... 46

Table 21: phyCORE-LPC3180 Carrier Board Jumper Settings ................... 48

Table 22: P300A BOOT/RESET Signal Operating Limits............................ 54

Table 23: A/D Potentiometer Output Routing Options ................................. 57

Table 24: Keyboard Connector X203 Signal Assignment............................ 59

Table 25: JTAG Connector X202 Signal Assignment .................................. 60

phyCORE-LPC3180

©PHYTEC America LLC 2007 L-681e_3

Table 26: GPI Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 63

Table 27: GPO Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 64

Table 28: GPIO Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 64

Table 29: SPI Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 65

Table 30: SD Card Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 65

Table 31: USB Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 65

Table 32: JTAG/DEBUG Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 66

Table 33: System Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 66

Table 34: A/D Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 67

Table 35: PWM Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 67

Table 36: I²C Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 67

Table 37: UART Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 68

Table 38: Keyboard Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 69

Table 39: Power Pin Assignment for the phyCORE-LPC3180 /

Carrier Board / Expansion Board ................................................. 69

Table 40: Carrier Board Generated Signal Pin Assignment for the

phyCORE-LPC3180 / Carrier Board / Expansion Board.............. 70

Table 41: Unused Pins on the phyCORE-LPC3180 / Carrier Board /

Expansion Board.......................................................................... 70

Preface

PREFACE

This phyCORE-LPC3180 Hardware Manual describes the single board computer’s design and

functions. Precise specifications for the NXP Semiconductors (founded by Philips) LPC3180

microcontrollers can be found in the enclosed microcontroller Data Sheet/User's Manual. If software is

included please also refer to additional documentation for this software.

In this hardware manual and in the attached schematics, low active signals are denoted by a "/"

preceding the signal name (i.e.: /RD). A "0" indicates a logic-zero or low-level signal, while a "1"

represents a logic-one or high-level signal.

Declaration of Electro Magnetic Conformity of the PHYTEC

©PHYTEC America LLC 2007 L-681e_3 1

phyCORE-LPC3180

PHYTEC Single Board Computers (henceforth products) are designed for installation in electrical

appliances or as dedicated Evaluation Boards (i.e.: for use as a test and prototype platform for

hardware/software development) in laboratory environments.

Caution:

PHYTEC products lacking protective enclosures are subject to damage by ESD and, hence, may only

be unpacked, handled or operated in environments in which sufficient precautionary measures have

been taken in respect to ESD-dangers. It is also necessary that only appropriately trained personnel

(such as electricians, technicians and engineers) handle and/or operate these products. Moreover,

PHYTEC products should not be operated without protection circuitry if connections to the product's

pin header rows are longer than 3 m.

PHYTEC products fulfill the norms of the European Union’s Directive for Electro Magnetic Conformity

only in accordance to the descriptions and rules of usage indicated in this hardware manual

(particularly in respect to the pin header row connectors, power connector and serial interface to a

host-PC).

Implementation of PHYTEC products into target devices, as well as user modifications and extensions

of PHYTEC products, is subject to renewed establishment of conformity to, and certification of,

Electro Magnetic Directives. Users should ensure conformance following any modifications to the

products as well as implementation of the products into target systems.

The phyCORE-LPC3180 is one of a series of PHYTEC Single Board Computers that can be

populated with different controllers and, hence, offers various functions and configurations. PHYTEC

supports a variety of 8-/16- and 32-bit controllers in two ways:

(1) as the basis for Rapid Development Kits which serve as a reference and evaluation platform

(2) as insert-ready, fully functional phyCORE OEM modules, which can be embedded directly into

the user’s peripheral hardware, design.

PHYTEC's microcontroller modules allow engineers to shorten development horizons, reduce design

costs and speed project concepts from design to market. For more information go to:

http://www.phytec.com/services/phytec-advantage.html

phyCORE-LPC3180

2©PHYTEC America LLC 2007 L-681e_3

1INTRODUCTION

The phyCORE-LPC3180 belongs to PHYTEC’s phyCORE Single Board Computer module family.

The phyCORE SBCs represent the continuous development of PHYTEC Single Board Computer

technology. Like its mini-, micro- and nanoMODUL predecessors, the phyCORE boards integrate all

core elements of a microcontroller system on a subminiature board and are designed in a manner

that ensures their easy expansion and embedding in peripheral hardware developments.

As independent research indicates that approximately 70 % of all EMI (Electro Magnetic Interference)

problems stem from insufficient supply voltage grounding of electronic components in high frequency

environments the phyCORE board design features an increased pin package. The increased pin

package allows dedication of approximately 20 % of all pin header connectors on the phyCORE

boards to Ground. This improves EMI and EMC characteristics and makes it easier to design complex

applications meeting EMI and EMC guidelines using phyCORE boards even in high noise

environments.

phyCORE boards achieve their small size through modern SMD technology and multi-layer design. In

accordance with the complexity of the module, 0402-packaged SMD components and laser-drilled

Microvias are used on the boards, providing phyCORE users with access to this cutting edge

miniaturization technology for integration into their own design.

The phyCORE-LPC3180 is a subminiature (60 x 53 mm) insert-ready Single Board Computer

populated with the NXP Semiconductors (founded by Philips) LPC3180 microcontroller. Its universal

design enables its insertion in a wide range of embedded applications. All controller signals and ports

extend from the controller to high-density pitch (0.635 mm) connectors aligning two sides of the

board, allowing it to be plugged like a "big chip" into a target application.

Precise specifications for the controller populating the board can be found in the applicable controller

User’s Manual or datasheet. The descriptions in this manual are based on the NXP Semiconductors

(founded by Philips) LPC3180. No description of compatible microcontroller derivative functions is

included, as such functions are not relevant for the basic functioning of the phyCORE-LPC3180.

Andere Handbücher für phyCORE-LPC3180

Inhaltsverzeichnis

Andere Phytec Computerhardware Handbücher

Phytec

Phytec IoT-Enablement-Kit 4 Bedienungsanleitung

Phytec

Phytec eGrabber-4plus Bedienungsanleitung

Phytec

Phytec phyCORE-AM335 Series Bedienungsanleitung

Phytec

Phytec i.MX7 PEB-D-RPI Bedienungsanleitung

Phytec

Phytec phyCORE-DS80C390 Programmierhandbuch

Phytec

Phytec L-1029e.A1 Bedienungsanleitung

Phytec

Phytec phyFLEX-i.MX 6 Bedienungsanleitung

Phytec

Phytec phyCORE-LPC3180 Programmierhandbuch

Phytec

Phytec ATOM phyCORE-Z500P(T) Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX 8M Mini Bedienungsanleitung

Phytec

Phytec L-1014e.A4 phyBOARD-Mira Bedienungsanleitung

Phytec

Phytec phyCORE-MPC5676/57 Series Bedienungsanleitung

Phytec

Phytec phyCORE-LPC3250 Bedienungsanleitung

Phytec

Phytec PCAN-Dongle PK-001 Programmierhandbuch

Phytec

Phytec phyCORE-i.MX 8M Mini Bedienungsanleitung

Phytec

Phytec PhyBOARD-Mira i.MX6 Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX 8M Plus Bedienungsanleitung

Phytec

Phytec L-1009e.A2 phyCORE-i.MX 8M Plus Bedienungsanleitung

Phytec

Phytec phyGATE Tauri-L Bedienungsanleitung

Phytec

Phytec phyCORE-PXA270 Programmierhandbuch

Phytec

Phytec phyCORE-PXAG49 Programmierhandbuch

Phytec

Phytec KEIL nanoMODUL-STM32F103 Programmierhandbuch

Phytec

Phytec L-808e.A4 Bedienungsanleitung

Phytec

Phytec phyCORE MPC5676 Series Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Phytec phyCORE-LPC3180 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken