Phytec PhyCORE-TC399 Bedienungsanleitung

A product of a PHYTEC Technology Holding company

phyCORE®-TC399

Hardware Manual

Document No.: L-853e.A0

SOM Prod. No.: KSP-0200-0.Ax

SOM PCB. No.: 4628.0

Edition:November 2018

phyCORE®-TC399[KSP-0200-0.A0]

PHYTEC Messtechnik GmbH 2018 L-853e.A0

Copyrighted products are not explicitly indicated in this manual. The

absence of the trademark (, or ®) and copyright (©) symbols does not

imply that a product is not protected. Additionally, registered

patents and trademarks are similarly not expressly indicated in this

manual.

The information in this document has been carefully checked and is

considered to be entirely reliable. However, PHYTEC Messtechnik GmbH

assumes no responsibility for any inaccuracies. PHYTEC Messtechnik

GmbH neither gives any guarantee nor accepts any liability whatsoever

for consequential damages resulting from the use of this manual or

its associated product. PHYTEC Messtechnik GmbH reserves the right to

alter the information contained herein without prior notification and

accepts no responsibility for any damages that might result.

Additionally, PHYTEC Messtechnik GmbH offers no guarantee nor accepts

any liability for damages arising from the improper usage or improper

installation of the hardware or software. PHYTEC Messtechnik GmbH

further reserves the right to alter the layout and/or design of the

hardware without prior notification and accepts no liability for

doing so.

Rights - including those of translation, reprint, broadcast,

photomechanical or similar reproduction and storage or processing in

computer systems, in whole or in part - are reserved. No reproduction

may occur without the express written consent from PHYTEC Messtechnik

GmbH.

EUROPE

NORTH AMERICA

FRANCE

Address:

PHYTEC Messtechnik

GmbH

Robert-Koch-Str. 39

D-55129 Mainz

GERMANY

PHYTEC America LLC

203 Parfitt Way SW

Bainbridge Island,

WA 98110

USA

PHYTEC France

17, place Saint-

Etienne

F-72140 Sillé-le-

Guillaume

FRANCE

Ordering

Informati

on:

+49 6131 9221-32

[email protected]

+1 800 278-9913

[email protected]

+33 2 43 29 22 33

[email protected]

Technical

Support:

+49 6131 9221-31

[email protected]

+1 206 780-9047

[email protected]

Fax:

+49 6131 9221-33

+1 206 780-9135

+33 2 43 29 22 34

Web Site:

http://www.phytec.de

http://www.phytec.eu

http://www.phytec.co

http://www.phytec.fr

INDIA

CHINA

Address:

PHYTEC Embedded Pvt. Ltd.

#16/9C, 3rd Main, 3rd

Floor, 8th Block,

Opp. Police Station

PHYTEC Information Technology

(Shenzhen) Co. Ltd.

Suite 2611, Floor 26, Anlian Plaza,

4018 Jin Tian Road

XXX

PHYTEC Elektronik GmbH 2012 L-769e_1

Koramangala, Bangalore-

560095

INDIA

Futian District, Shenzhen

CHINA 518026

Ordering

Informati

on:

+91-80-4086 7046/48

[email protected]

+86-755-3395-5875

[email protected]

Technical

Support:

+91-80-4086 7047

[email protected]

Fax:

+86-755-3395-5999

Web Site:

http://www.phytec.in

http://www.phytec.cn

1st Edition #### 2018

Contents

PHYTEC Messtechnik GmbH 2018---L-853e.A0 i

List of Figures .............................................. ii

List of Tables .............................................. iii

Conventions, Abbreviations and Acronyms ...................... iv

Preface ..................................................... vii

1Introduction............................................... 1

1.1 Features of the phyCORE-TC399 .......................... 2

1.1.1 Internal Features of the TC399.................... 2

1.1.2 Memory Configuration of the phyCORE-TC399......... 2

1.1.3 Other Board-Level Features of the phyCORE-TC399... 2

1.2 Block Diagram .......................................... 3

1.3 Component Placement Diagram ............................ 4

1.4 Minimum Requirements to operate the phyCORE-TC399 ...... 6

2Pin Description............................................ 7

3Jumpers................................................... 27

4Power..................................................... 39

4.1 Standby Power Supply .................................. 39

5Reset..................................................... 41

6System Configuration and Booting.......................... 42

6.1 Internal start ........................................ 42

6.2 Bootloader Modes ...................................... 42

6.2.1 Alternate Boot Modes (ABM)....................... 42

7System Memory............................................. 44

7.1 External Asynchronous SRAM_BANK 1 and 2 (U17-U20)) .... 44

7.2 SPI EEPROM Flash Memory (U8) .......................... 44

8uSD Card Interface (SPI Mode) X4.......................... 46

9Serial Interfaces......................................... 47

9.1 Universal Asynchronous Interface ...................... 47

9.2 USB to UART Bridge Host Interface ..................... 48

9.3 Ethernet Interface .................................... 49

9.3.1 Ethernet PHY (U12)............................... 49

9.3.2 Ethernet Controller (U21)........................ 51

9.3.3 MAC Address...................................... 51

9.4 SPI Interface ......................................... 52

9.5 I2C Interface ......................................... 52

9.6 CAN Interface ......................................... 53

10 Real Time Clock (RTC-8564)(U9)............................ 55

11 User LED.................................................. 56

12 On-Chip Debug Support Interface........................... 57

13 Technical Specifications.................................. 58

14 Hints for Intergrating and Handling the phyCORE-TC399..... 61

14.1 Integrating the phyCORE-TC399.................... 61

14.2 Evaluating the phyCORE-TC399 with the corresponding

Evaluation Kit “KSP-022-KIT” .......................... 63

14.3 Handling the phyCORE-TC399....................... 63

15 Revision History.......................................... 64

phyCORE®-TC399[KSP-0200-0.A0]

ii PHYTEC Messtechnik GmbH 2018 L-853e.A0

16 Index .....................................................64

List of Figures

Figure 1: Block Diagram of the phyCORE-TC399 ................3

Figure 2: phyCORE–TC399 Component Placement (top view) ......4

Figure 3: phyCORE-TC399 Component Placement (bottom view) ...5

Figure 4: Pinout of the phyCORE-Connector (top view) ........8

Figure 5: Typical Jumper Pad Numbering Scheme ..............27

Figure 6: Jumper Locations (top view) ......................29

Figure 7: Jumper Locations (bottom view) ...................30

Figure 8: OnBoard SPI EEPROM/Flash connection ..............45

Figure 9: On-board uSD Card Interface (in SPI-Mode)

connection............................................46

Figure 10: onBoard OCDS/JTAG connector ......................57

Figure 11: onBoard DAPG connector ...........................57

Figure 12: Physical Dimensions (top view) ...................58

Figure 13: Footprint of the phyCORE-TC399 ...................62

Contents

PHYTEC Messtechnik GmbH 2018---L-853e.A0 iii

List of Tables

Table 1:Signal Types used in this Manual ...................... v

Table 2:Abbreviations and Acronyms used in this Manual ....... vi

Table 3:Pinout of the phyCORE-Connector X3, RowA ............. 10

Table 4:Pinout of the phyCORE-Connector X3, RowB ............. 14

Table 5:Pinout of the phyCORE-Connector X3, RowC ............. 17

Table 6:Pinout of the phyCORE-Connector X3, Row D ............ 21

Table 7:Pinout of the optional phyCORE-Connection X2, Row A .. 24

Table 8:Pinout of the optional phyCORE-Connection X2, Row B .. 25

Table 9:Jumper Settings ...................................... 32

Table 10:.................................................................... Boot Modes of the phyCORE-TC399 43

Table 11:.................... Boot Configuration Pins at the phyCORE-Connector 43

Table 12:............................................................................. Location of the UART Signals 48

Table 13:................................................................. Location of the USB Host Signals 49

Table 14:................................................................. Location of the Ethernet Signals 50

Table 15:................................................ Table MAC address Example 0050C2A0C093 52

Table 16:........................................................................... I2C Interface Signal Location 53

Table 17:........................................................................................ Technical Specifications 59

phyCORE®-TC399[KSP-0200-0.A0]

iv PHYTEC Messtechnik GmbH 2018 L-853e.A0

Conventions, Abbreviations and Acronyms

This hardware manual describes the KSP-0200 System on

Module, henceforth referred to as phyCORE®-TC399. The manual

specifies the phyCORE®-TC399's design and function. Precise

specifications for the Infineon® Semiconductor TC399

microcontrollers can be found in the enclosed

microcontroller Data Sheet/User's Manual.

Note: We refrain from providing detailed, part specific

information within this manual, which can be subject to

continuous changes, due to part maintenance for our

products. Please read the section"Product Change Management

and information in this manual on parts populated on the

SOM" within the Preface.

Conventions

The conventions used in this manual are as follows:

Signals that are preceded by an "n", "/", or “#”character

(e.g.: nRD, /RD, or #RD), or that have a dash on top of

the signal name (e.g.: RD) are designated as active low

signals. That is, their active state is when they are

driven low, or are driving low.

A "0" indicates a logic zero or low-level signal, while a

"1" represents a logic one or high-level signal.

The hex-numbers given for addresses of I2C devices always

represent the 7 MSB of the address byte. The correct

value of the LSB which depends on the desired command

(read (1), or write (0)) must be added to get the

complete address byte. E.g. given address in this manual

0x41 => complete address byte = 0x83 to read from the

device and 0x82 to write to the device

Tables which describe jumper settings show the default

position in bold, blue text.

Text in blue italic indicates a hyperlink within, or

external to the document. Click these links to quickly

jump to the applicable URL, part, chapter, table, or

figure.

References made to the phyCORE-Connector always refer to

the high density Samtec connector on the undersides of

the phyCORE-i.MX°8M System on Module.

Conventions, Abbreviations and Acronyms

PHYTEC Messtechnik GmbH 2018---L-853e.A0 v

Types of Signals

Different types of signals are brought out at the phyCORE-

Connector. The following table lists the abbreviations used

to specify the type of a signal.

Signal

Type

Description Abbr.

Power

Supply voltage input

PWR_I

Ref-

Voltage

Reference voltage output

REF_O

Input

Digital input

Output

Digital output

Bidirectional input/output

I/O

OC-Bidir

Open collector input/output with pull

OC-BI

OC-Output

Open collector output without pull up,

requires an external pull up

USB IO

Differential line pairs 90 Ohm USB

level bidirectional input/output

USB_I/

ETHERNET

Input

Differential line pairs 100 Ohm

Ethernet level input

ETH_I

ETHERNET

Output

Differential line pairs 100 Ohm

Ethernet level output

ETH_O

ETHERNET

Differential line pairs 100 Ohm

Ethernet level bidirectional

input/output

ETH_I/

USB IO

Differential line pairs 90 Ohm USB

level bidirectional input/output

USB_I/

Table 1: Signal Types used in this Manual

phyCORE®-TC399[KSP-0200-0.A0]

vi PHYTEC Messtechnik GmbH 2018 L-853e.A0

Abbreviations and Acronyms

Many acronyms and abbreviations are used throughout this

manual. Use the table below to navigate unfamiliar terms

used in this document.

Abbreviation

Definition

Carrier Board; used in reference to the

phyCORE Development Kit Carrier Board.

DFF

D flip-flop.

EMB

External memory bus.

EMI

Electromagnetic Interference.

GPI

General purpose input.

GPIO

General purpose input and output.

GPO

General purpose output.

IRAM

Internal RAM; the internal static RAM on the

Infineon® Semiconductor TC399

microcontroller.

Solder jumper; these types of jumpers

require solder equipment to remove

and

place.

Solderless jumper; these types of jumpers

can be removed and placed by hand with

special tools.

PCB

Printed circuit board.

PEB

PHYTEC Extension Board

POR

Power-on reset

RTC

Real-time clock.

SMT

Surface mount technology.

SOM

System on Module; used in reference to the

phyCORE-TC399 module

User button Sx (e.g. S1, S2, etc.) used in

reference to the available user

buttons, or

DIP-Switches on the carrier board.

Sx_y

Switch y of DIP-Switch Sx; used in reference

to the DIP-Switch on the carrier board.

Table 2: Abbreviations and Acronyms used in this Manual

Preface

PHYTEC Messtechnik GmbH 2018---L-853e.A0 vii

Preface

As a member of PHYTEC's phyCORE®product family, the

phyCORE-TC399 is one of a series of PHYTEC System on

Modules (SOMs) that can be populated with different

controllers and, thereforeoffers various functions and

configurations. PHYTEC supports a variety of 8-/16- and 32-

bit controllers in two ways:

(1) as the basis for Rapid Development Kits which serve as

a reference and evaluation platform

(2) as insert-ready, fully functional phyCORE®OEM modules,

which can be embedded directly into the user’s

peripheral hardware design.

Implementation of an OEM-able SOM subassembly as the "core"

of your embedded design allows for increased focus on

hardware peripherals and firmware without expending

resources to "re-invent" microcontroller circuitry.

Furthermore, much of the value of the phyCORE®module lies

in its layout and test.

Production-ready Board Support Packages (BSPs) and Design

Services for our hardware will further reduce development

time and risk and allows for increased focus on the product

expertise. Take advantage of PHYTEC products to shorten

time-to-market, reduce development costs, and avoid

substantial design issues and risks. With this new

innovative full system solution,new ideas can be brought

to market in the most timely and cost-efficient manner.

For more information go to:

http://www.phytec.de/de/leistungen/entwicklungsunterstuetzu

ng.html

http://www.phytec.eu/europe/oem-integration/evaluation-

start-up.html

Inhaltsverzeichnis

Andere Phytec Computerhardware Handbücher

Phytec

Phytec L-1029e.A1 Bedienungsanleitung

Phytec

Phytec L-1014e.A4 phyBOARD-Mira Bedienungsanleitung

Phytec

Phytec phyGATE Tauri-L Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX RT1170 Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX 8M Mini Bedienungsanleitung

Phytec

Phytec Cosmic-AM335 Series Bedienungsanleitung

Phytec

Phytec L-863e.A2 phyCORE-i.MX 8M Bedienungsanleitung

Phytec

Phytec phyCORE-MPC5676/57 Series Bedienungsanleitung

Phytec

Phytec phyCORE-PXA270 Programmierhandbuch

Phytec

Phytec L-808e.A4 Bedienungsanleitung

Phytec

Phytec phyCORE-LPC3180 Bedienungsanleitung

Phytec

Phytec ATOM phyCORE-Z500P(T) Bedienungsanleitung

Phytec

Phytec phyCORE-AM335 Series Bedienungsanleitung

Phytec

Phytec phyCORE-AM62Ax Bedienungsanleitung

Phytec

Phytec phyCORE-i.MX 8M Mini Bedienungsanleitung

Phytec

Phytec eGrabber-4plus Bedienungsanleitung

Phytec

Phytec phyCORE MPC5676 Series Bedienungsanleitung

Phytec

Phytec IoT-Enablement-Kit 4 Bedienungsanleitung

Phytec

Phytec phyFLEX-i.MX 6 Bedienungsanleitung

Phytec

Phytec L-820e.A2 Bedienungsanleitung

Phytec

Phytec phyCORE-MPC5554 Bedienungsanleitung

Phytec

Phytec PCAN-Dongle PK-001 Programmierhandbuch

Phytec

Phytec PhyBOARD-Mira i.MX6 Bedienungsanleitung

Phytec

Phytec microMODUL-8051 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

AMD

AMD Phenom II Betriebshandbuch

Intel

Intel NUC 12 Pro Bedienungsanleitung

dbx

dbx Zone Pro 1260 Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Phytec phyCORE-TC399 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken