Pickering 40-616A Bedienungsanleitung

pickeringtest.com

Issue 1.1 March 2020

40-616A User Manual

PXI 16 Bank, 5 Channel, 1-Pole Multiplexer Module

Page (II) 16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) 16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering

Page (IV) REED RELAY MODULE 40-110/115/120/125

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy reference should be made to the safety instructions for

provisions of lifting and moving.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering

Technical Support and Warranty................................................III

Product Safety .............................................................................IV

Contents (this page)....................................................................V

Warnings and Cautions ..............................................................VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description..........................................................2.1

Section 3

Installation....................................................................................3.1

Pre Operation Checks...........................................................3.1

Hardware Installation ............................................................3.2

Software Installation .............................................................3.2

Testing Operation ..................................................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options For Pickering PXI Modules ............4.1

Module Architecture..............................................................4.2

Programming The Module ....................................................4.4

Section 5

Connector Information................................................................5.1

Section 6

Trouble Shooting .........................................................................6.1

Section 7

Maintenance Information............................................................7.1

Switching System Test Tools ...............................................7.1

Relay Lookup Table 40-616A ...............................................7.2

Component Layout 40-616A. ...............................................7.3

CONTENTS

Page (VI) 16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering

Page (VII)

2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

WARNINGS AND CAUTIONS

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

Unused slots in the host chassis are populated with blanking plates to prevent access to user I/O

signals that may be present. Blanking panels are available to order from Pickering in a variety of

slot widths. If the product is not used in this manner for example by using an extender card then

additional care must be taken to avoid contact with exposed signals.

Not to be used in safety critical circuits, refer to the Pickering Interfaces’ terms & conditions of sale.

This module must not be used for the switching of Mains Circuits. For the switching of voltages up

to the module’s full specication, Secondary Circuit power supplies and the Device Under Test must

be fully isolated from the Mains Circuit and the safety earth.

The host chassis must be correctly installed and be connected to mains or factory safety ground,

please refer to your chassis installation manual.

Diagram Showing Separation Between The Mains Circuit and Secondary Circuit / DUT

For the purposes of this document, a Mains Circuit is an installation classied as Overvoltage

Category II up to 300V. Separation between the Secondary Circuit and Mains Circuit is achieved

by a transformer in which the primary windings are separated from the secondary windings by

reinforced insulation, double insulation, or a screen connected to the protective conductor terminal.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

PXI Switching

Module

Device

Under Test

Power

Supply

Power

Supply

Host Chassis

Secondary Circuit

Mains

Circuit

Mains

Circuit

Mains/Factory

Safety Ground

Page (VIII) 16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering

Page (VIII) 2 AMP 1-POLE UHD MATRIX MODULES 40-575 / 576 / 577 / 578 / 579

pickering

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page 1.1

16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

PXI 16-Bank, 5-Channel, 1-Pole Multiplexer 40-616A

ISSUE 1.0 FEB 2019

Supported by

eBIRST

eBIRST switching system test tools simplify fault-nding by quickly

testing the system and graphically identifying the faulty relay.

For more information go to: pickeringtest.com/ebirst

• 16 Separate Multiplexers in One Module

• Each Multiplexer is Single Pole, 5-Way

• Features Isolation Switches to Reduce Signal Loading

• Inter-Bank Linking Relays Allow Multiplexer

Size to be Increased in Multiples of 5

• Multiplexer Channels Can be Set Individually

• Any Number of Multiplexer Channels Can be

Set Simultaneously

• Switches Up To 100 Volts, 1 Amp, 20 Watt.

• Uses High Reliability Ruthenium Reed Relays

for Maximum Performance

• VISA & Kernel Drivers Supplied for Windows

• Supported by PXI or LXI Chassis

• Supported by

eBIRST

™

• 3 Year Warranty

Com

Multiplexer Bank 1

Isolation

Switch

Chan 4

Chan 1

Chan 2

Chan 3

Chan 5

Com

Isolation

Switch

Chan 4

Chan 1

Chan 2

Chan 3

Chan 5

Com

Isolation

Switch

Chan 4

Chan 1

Chan 2

Chan 3

Chan 5

Multiplexer Bank 2 Multiplexer Bank 16

Inter-Bank Linking Switch Inter-Bank Linking Switch

Switching Diagram for the 40-616A 16-Bank, 5-Channel, 1-Pole Multiplexer

The 40-616A module consists of 16 separate multiplexer banks

controlled by a PXI interface. Each bank is a 1 to 5 multiplexer

and inter-bank linking relays allow the size of a multiplexer to be

increased in multiples of 5 by joining the common terminals of

adjacent banks. Closing one linking switch produces a 10 channel

multiplexer, closing all linking switches produces an 80 channel

multiplexer.

The 40-616A can be operated as a conventional multiplexer

with break-before-make action when a new channel is selected.

Alternatively, product variants can be supplied that allow multiple

channels to be simultaneously selected.

The 40-616A channel selection congurations have been revised

from the 40-616. The 40-616A defaults to single channel selection

with multiple channel selection variants dened by use of a sufx.

The multiplexers include isolation switching that connects only

the currently active multiplexer bank to its common terminal.

This minimizes capacitive loading and leakage current in large

multiplexer systems.

The module can be cascaded for applications that require large

multiplexer systems, it is also suitable for test systems that require

a large number of signals to be switched in parallel.

Page 1.2 16 BANK, 5 CHANNEL, 1-POLE MULTIPLEXER MODULE 40-616A

pickering

SECTION 1 - TECHNICAL SPECIFICATION

16-Bank, 5-Channel, 1-Pole MUX – 40-616A

pickeringtest.com

Speciﬁcations

Switching Speciﬁcation

Switch Type: Ruthenium Reed

Max Switching Voltage: 100V*

Max Power:

Max Switch Current:

Max Carry Current:

20W

Initial On Path Resistance:

Off Path Resistance:

Thermal Offset:

<700mΩ (single module)

>109Ω(single module)

<10µV

Operate Time: 1ms typical,

500µs for multichannel mode

Expected Life, low power load:

Expected Life, full power load:

>1x109 operations

>1x106 operations

* For full voltage rating, signal sources to be switched must be fully

isolated from mains supply and safety earth.

Power Requirements

+3.3V +5V +12V -12V

00.3A typical

1.4A max

0 0

Operating/Storage Conditions

Operating Conditions

Operating Temperature:

Humidity:

Altitude:

0°C to +55°C

Up to 90% non-condensing

5000m

Storage and Transport Conditions

Storage Temperature:

Humidity:

Altitude:

-20°C to +75°C

Up to 90% non-condensing

15000m

PXI & CompactPCI Compliance

The module is compliant with the PXI Specication 2.2. Local Bus,

Trigger Bus and Star Trigger are not implemented.

Uses a 33MHz 32-bit backplane interface.

Safety & CE Compliance

All modules are fully CE compliant and meet applicable EU

directives: Low-voltage safety EN61010-1:2010, EMC Immunity

EN61326-1:2013, Emissions EN55011:2009+A1:2010.

Mechanical Characteristics

Single slot 3U PXI (CompactPCI card).

3D models for all versions in a variety of popular le formats are

available on request.

Connectors

PXI bus via 32-bit P1/J1 backplane connector.

Signals via front panel 96-pin male micro-D connector, for pin outs

please refer to the operating manual.

Relay Type

The 40-616A is tted with ruthenium sputtered reed relays, these

offer very long life with good low level switching performance and

excellent contact resistance stability. Spare reed relays are built

onto the circuit board to allow easy maintenance with minimum

downtime.

All reed relays are manufactured by our sister company Pickering

Electronics: pickeringrelay.com

PCB Layout for the 40-616A 16-Bank,

5-Channel, 1-Pole Multiplexer Module

RF Speciﬁcation

Bandwidth (-3dB): 20MHz

Crosstalk - Bank (typical): 10kHz:

100kHz:

1MHz:

10MHz:

-80dB

-70dB

-60dB

-40dB

Crosstalk - Channel (typical): 10kHz:

100kHz:

1MHz:

10MHz:

-80dB

-60dB

-40dB

-20dB

Isolation (typical): 10kHz:

100kHz:

1MHz:

10MHz:

80dB

60dB

40dB

20dB

Inhaltsverzeichnis

Andere Pickering Multiplexer Handbücher

Pickering

Pickering 40-655A Bedienungsanleitung

Pickering

Pickering 60-590 Bedienungsanleitung

Pickering

Pickering SYSTEM 10 Bedienungsanleitung

Pickering

Pickering 40-614C Bedienungsanleitung

Pickering

Pickering 40-657 Bedienungsanleitung

Pickering

Pickering 40-756 Bedienungsanleitung

Pickering

Pickering PXI 40-620 Bedienungsanleitung

Pickering

Pickering PXI 40-620A Bedienungsanleitung

Pickering

Pickering 40-616 Bedienungsanleitung

Pickering

Pickering 40-670 Bedienungsanleitung

Pickering

Pickering 40-666 Bedienungsanleitung

Pickering

Pickering 50-670C Bedienungsanleitung

Pickering

Pickering PXI 40-661A Bedienungsanleitung

Pickering

Pickering 40-630A Bedienungsanleitung

Pickering

Pickering 4 784B Series Bedienungsanleitung

Pickering

Pickering 40-667B Bedienungsanleitung

Pickering

Pickering PXI 40-748 1 Series Bedienungsanleitung

Pickering

Pickering 40-614 Bedienungsanleitung

Pickering

Pickering 40-658A Bedienungsanleitung

Pickering

Pickering 40-784A Bedienungsanleitung

Pickering

Pickering 20-745 Bedienungsanleitung

Pickering

Pickering PXi 40-660A Bedienungsanleitung

Pickering

Pickering 42-204 Bedienungsanleitung

Pickering

Pickering PXI 40-740 Bedienungsanleitung

Beliebte Multiplexer Handbücher anderer Marken

Campbell

Campbell AM416 Bedienungsanleitung

Paradyne

Paradyne SIM2000 Bedienungsanleitung

Panasonic

Panasonic WJFS616 - SWITCHER Bedienungsanleitung

Lanex

Lanex TM-77 Bedienungsanleitung

Bosch

Bosch VSS8394/01T Bedienungsanleitung

Quark-Elec

Quark-Elec QK-A035 Bedienungsanleitung

ADTRAN

ADTRAN Frameport 768 Bedienungsanleitung

Elo TouchSystems

Elo TouchSystems E247 Bedienungsanleitung

Paradyne

Paradyne Hotwire 8786 Bedienungsanleitung

RFL Electronics

RFL Electronics 9508D UCC Bedienungsanleitung

Miranda

Miranda AMX-101i Bedienungsanleitung

ShipModul

ShipModul MiniPlex-AIX NMEA-0183 Bedienungsanleitung

GE StoreSafe SDVR-10 Bedienungsanleitung

American Fibertek

American Fibertek MTX-8410C Bedienungsanleitung

ADC

ADC HiGain ELU-319 5E Bedienungsanleitung

Paradyne

Paradyne Hotwire 8774 Bedienungsanleitung

American Fibertek

American Fibertek MTX-8810C-SL Bedienungsanleitung

Viessmann

Viessmann 5229 Bedienungsanleitung