PICO TA138 Bedienungsanleitung

TA138 200 A AC Current Clamp

OPERATING INSTRUCTIONS

Introduction

The TA138 200 A AC Current Clamp has a voltage output with standard banana

(4 mm) plugs for connection to the PicoLog CM3 Current Data Logger or other

compatible measuring instrument.

Using the Current Clamp Safely

Warning: To prevent electric shock or re and personal injury, carefully read

all safety information before attempting to operate the Current Clamp and

follow these procedures:

• DO NOT use the clamp on circuits rated higher than 600 V in Category II

or 300 V in Category III. Use caution when clamping around uninsulated

conductors or bus bars.

• DO NOT use a clamp that is cracked, damaged, or has a defective cable.

Such clamps should be made inoperative by taping the jaws closed.

• DO check the magnetic mating surfaces of the clamp jaws. They should be

free of dust, dirt, rust and other foreign matter.

• DO keep your ngers behind the safety barrier as shown below.

Safety Symbols

This symbol, adjacent to another symbol or terminal, indicates that

the user must refer to the manual for further information.

This symbol, adjacent to a terminal, indicates that, under normal

use, hazardous voltages may be present.

Double insulation

1. Current sense jaw

2. Clamp trigger

3. Safety barrier

4. Voltage output lead 200 A~

CAT III

300 V

Adaptor Description

Specications

• GeneralSpecications

Output impedance <1 kΩ

AC bandwidth 40 to 400 Hz

Jaw opening 16 mm

Operating conditions 32 °F to 86 °F (0 °C to 30 °C) 90% RH;

86 °F to 104 °F (30 °C to 40 °C) 75% RH;

104 °F to 122 °F (40 °C to 50 °C) 45% RH

Storage conditions -22 °F to 140 °F (-30 °C to 60 °C) <90% RH

Altitude Operate at less than 3000 metres

Weight 129 g

Dimensions 111 x 50 x 33 mm (H x W x D)

Standards IEC1010-1 (1995);

EN61010-1 (2001) Category II 600 V, Category III 300 V

• RangeSpecications

Function Range Output Sensitivity Accuracy (of reading)

AC Current (50/60 Hz) 0 to 200 A 1 mV/A 1 A/mV AC ±2.0%±0.5 A

Using the Current Clamp with the PicoLog Software

1. Connect the output lead to the input sockets of the PicoLog CM3 Current

Data Logger.

2. Connect the PicoLog CM3 to your computer using the USB cable supplied.

3. Position the Current Clamp perpendicular to and centered around the

conductor.

4. Run the PicoLog software on the computer.

5. Select File > New Settings and congure PicoLog for a ‘PLCM3’ device.

6. Select File > New Data and click the ‘Start recording’ button when ready.

Inhaltsverzeichnis

Andere PICO Prüfgeräte Handbücher

PICO

PICO PicoScope 3000 A Series Bedienungsanleitung

PICO

PICO -2000 Bedienungsanleitung

PICO

PICO TA041 Bedienungsanleitung

PICO

PICO PicoScope 2200 Series Bedienungsanleitung

PICO

PICO PicoScope 5000 A Bedienungsanleitung

PICO

PICO picoscope 3204 Bedienungsanleitung

PICO

PICO TA234 Bedienungsanleitung

PICO

PICO PicoScope 6000E Series Bedienungsanleitung

PICO

PICO PicoScope 5000 A Bedienungsanleitung

PICO

PICO PicoScope 9000 Series Bedienungsanleitung

PICO

PICO TA467 Bedienungsanleitung

PICO

PICO PicoScope 2000 Series Bedienungsanleitung

PICO

PICO PicoScope 4224 Bedienungsanleitung

PICO

PICO PicoScope 2104 Bedienungsanleitung

PICO

PICO PicoScope 5000 Series Handbuch

PICO

PICO ADC-10 Bedienungsanleitung

PICO

PICO PicoScope 4444 Bedienungsanleitung

PICO

PICO PicoScope 3000 Series Bedienungsanleitung

PICO

PICO PicoScope 9000 Series Bedienungsanleitung

PICO

PICO PicoScope 3204A Handbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung