Pilz PNOZ msi b4 Box Bedienungsanleitung

PNOZ msi b4 Box

Operating Manual 1003058-EN-03

}Accessories PNOZmulti

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

PNOZ msi b4 Box

Operating Manual PNOZ msi b4 Box

1003058-EN-03 3

Introduction

Validity of documentation

This documentation is valid for the product PNOZ msi b4 Box from Version 2.0 .

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

Description

The shielded junction box PNOZ msi b4 Box is used to connect

}An incremental encoder with an additional feed for the incremental encoder supply

}An incremental encoder in conjunction with a proximity switch with/without pull resistor

(dual encoder evaluation) with an additional supply for the proximity switch

}2 proximity switches with/without pull resistor with an additional supply for the proximity

switches

to the Pilz speed monitors.

Front view

PNOZ msi b4 Box

Operating Manual PNOZ msi b4 Box

1003058-EN-03 4

Installation

}The junction box should be installed in a control cabinet with a protection type of at

least IP54.

}Fit the junction box to a horizontal mounting rail.

}Use the locking slide on the rear of the junction box to attach it to a mounting rail.

}In environments exposed to heavy vibration, the unit should be secured using a fixing

element (e.g. retaining bracket or end angle).

}Open the locking slide before lifting the unit from the mounting rail.

Mounting distances

For the wiring to be EMC-compliant, the junction box must maintain a distance of at least

5.5 mm from other conductive parts (e.g. adjacent housing parts) (see diagram).

5,5 mm

(0.22“)

5,5 mm

(0.22“)

5,5 mm

(0.22“)

5,5 mm

(0.22“)

conductive parts

PNOZ msi b4 Box

Operating Manual PNOZ msi b4 Box

1003058-EN-03 5

Dimensions in mm

131,3 (5.17“)

100 (3.94“)

25 (0.98“)

103,18 (4.06“)

Connection

INFORMATION

The connected supply voltages and the sensors have to be supplied from

power supplies that comply with the regulations for extra low voltages with

safe electrical isolation.

Shielded line

Acorn nut

Sealing ring

Connecting piece

Braided shield

Lamellar insert

1. Remove the external insulation of the line and expose the braided shield, depending on

the conductor cross section, to approx. 10-15 mm.

2. Push acorn nut and lamellar insert with gasket onto the line.

3. Bend braided shield to the outside at a right angle (90°).

4. Crimp over braided shield towards the external cable insulation, i.e. crimp it over again

by 180°.

5. Insert connecting piece up to the braided shield and turn it shortly back and forth round

the line axis.

6. Push lamellar insert with gasket into the connecting piece and snap in the anti-twist pro-

tection.

7. Screw the acorn nut firmly.

PNOZ msi b4 Box

Operating Manual PNOZ msi b4 Box

1003058-EN-03 6

Internal view

The cable ducts and the corresponding terminals are each labelled identically (X1 ... X4).

}Cable ducts at X1 and X4:

Size M12x1.5 with terminals for cable diameters from 3 to 6.5 mm, tighten with spanner

size SW 14 mm and torque setting 8 Nm.

}Cable ducts at X2 and X3:

Size M16x1.5 with terminals for cable diameters from 5 to 9 mm, tighten with spanner

size SW 17 mm and torque setting 8 Nm.

The identically named signals (GND, S, 24 V...) are connected to each other between the

terminals X1 ... X4 internally.

INFORMATION

When using crimp connectors the connection wires can be inserted into the

connectors of the spring-loaded terminals. Pressing the operating pushbut-

ton is necessary only to undo the connection.

PNOZ msi b4 Box

Operating Manual PNOZ msi b4 Box

1003058-EN-03 7

Internal wiring diagram

AnA B nB ZnZ S24 V GND

AnA B nB ZnZ S 24 V GND

GND

24 V

GND

24 V

GND

24 V

GND

24 V

GND

PNOZ msi b4 Box

Operating Manual PNOZ msi b4 Box

1003058-EN-03 8

Connection examples

Example 1

Encoder directly to a speed monitor from Pilz, supply voltage for encoder via bridge at ter-

minals S - 24 V of connector X4,

Option: Wiring of encoder outputs (connector X3)

GND

24 V

GND

0 V

24 V

GND

24 V

Encoder

Speed monitor

from Pilz

PNOZ msi b4 Box

Operating Manual PNOZ msi b4 Box

1003058-EN-03 9

Example 2

Encoder and proximity switch (sensor type in PNOZmulti Config: HTL differential + Z fre-

quency Ini pnp) for monitoring for broken shearpins, do not connect Z and nZ of the en-

coder, supply voltage for encoder via bridge at terminals S - 24 V of connector X4,

Option: Wiring of the outputs of the encoder (connector X3) and pull-down resistor for Z

(connector X4)

GND

24 V

GND

0 V

24 V

GND

24 V

0 V

24 V

Encoder

Output

Proximity switch pnp

Speed monitor

from Pilz

PNOZ msi b4 Box

Operating Manual PNOZ msi b4 Box

1003058-EN-03 10

Example 3

2 proximity switches, supply voltage for proximity switches via connector X4

Option: Pull-down/pull-up resistance for A (connector X2), pull-down/pull-up resistance for

B (connector X4), monitoring track S (connector X4)

GND

24 V

GND

0 V

24 V

GND

24 V

0 V

24 V

0 V

Output

Proximity switch pnp/

npn

Proximity switch pnp/

npn

Output

Speed monitor

from Pilz

Inhaltsverzeichnis

Andere Pilz Relais Handbücher

Pilz

Pilz PNOZ s20 Bedienungsanleitung

Pilz

Pilz PNOZ XV2 Bedienungsanleitung

Pilz

Pilz PNOZ pe1p Bedienungsanleitung

Pilz

Pilz PNOZ X2.4V Bedienungsanleitung

Pilz

Pilz PNOZ mc9p Bedienungsanleitung

Pilz

Pilz S1UK Bedienungsanleitung

Pilz

Pilz PST 4 Bedienungsanleitung

Pilz

Pilz PZE X4VP8 Bedienungsanleitung

Pilz

Pilz P2HZ X4P Bedienungsanleitung

Pilz

Pilz PNOZ X2.7P Bedienungsanleitung

Pilz

Pilz PNOZ e4.1p Bedienungsanleitung

Pilz

Pilz PNOZ X2.1C Bedienungsanleitung

Pilz

Pilz PNOZ X3P Bedienungsanleitung

Pilz

Pilz PNOZ pps1p Bedienungsanleitung

Pilz

Pilz S1IM/UP Bedienungsanleitung

Pilz

Pilz PNOZ s6.1 Bedienungsanleitung

Pilz

Pilz PSEN im1 Bedienungsanleitung

Pilz

Pilz PNOZ X3 Betriebsanleitung

Pilz

Pilz PNOZ 2VJ Bedienungsanleitung

Pilz

Pilz PZE X5 Bedienungsanleitung

Pilz

Pilz PNOZ Ex Bedienungsanleitung

Pilz

Pilz PNOZ X2 Bedienungsanleitung

Pilz

Pilz PNOZ e6vp Bedienungsanleitung

Pilz

Pilz PNOZ X3 Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung

Littelfuse

Littelfuse SE-330AU Bedienungsanleitung