Pilz PNOZ pe2p Bedienungsanleitung

PNOZ pe2p

Operating Manual 21035-EN-03

}Safety relays

Preface

This document is a translation of the original document.

All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made

for internal purposes. Suggestions and comments for improving this documentation will be

gratefully received.

Source code from third-party manufacturers or open source software has been used for

some components. The relevant licence information is available on the Internet on the Pilz

homepage.

Pilz®, PIT®, PMI®, PNOZ®, Primo®, PSEN®, PSS®, PVIS®, SafetyBUS p®,

SafetyEYE®, SafetyNET p®, the spirit of safety® are registered and protected trademarks

of Pilz GmbH & Co. KG in some countries.

SD means Secure Digital

Contents

Operating Manual PNOZ pe2p

21035-EN-03 3

Introduction 4

Validity of documentation 4

Using the documentation 4

Definition of symbols 4

Safety 5

Intended use 5

Safety regulations 6

Use of qualified personnel 6

Warranty and liability 6

Disposal 6

Unit features 7

Block diagram/terminal configuration 7

Function Description 7

Operating modes 7

Installation 8

Wiring 9

Preparing for operation 9

Operation 9

Signal statuses of the inputs and outputs 9

Technical details 10

Order reference 11

EC declaration of conformity 11

PNOZ pe2p

Operating Manual PNOZ pe2p

21035-EN-03 4

Introduction

Validity of documentation

This documentation is valid for the product PNOZ pe2p. It is valid until new documentation

is published.

This operating manual explains the function and operation, describes the installation and

provides guidelines on how to connect the product.

Using the documentation

This document is intended for instruction. Only install and commission the product if you

have read and understood this document. The document should be retained for future ref-

erence.

Definition of symbols

Information that is particularly important is identified as follows:

DANGER!

This warning must be heeded! It warns of a hazardous situation that poses

an immediate threat of serious injury and death and indicates preventive

measures that can be taken.

WARNING!

This warning must be heeded! It warns of a hazardous situation that could

lead to serious injury and death and indicates preventive measures that can

be taken.

CAUTION!

This refers to a hazard that can lead to a less serious or minor injury plus

material damage, and also provides information on preventive measures

that can be taken.

NOTICE

This describes a situation in which the product or devices could be dam-

aged and also provides information on preventive measures that can be

taken. It also highlights areas within the text that are of particular import-

ance.

PNOZ pe2p

Operating Manual PNOZ pe2p

21035-EN-03 5

INFORMATION

This gives advice on applications and provides information on special fea-

tures.

Safety

Intended use

The PNOZ pe2p bus interface, together with an expansion module of the PNOZpower mod-

ular safety system, are used for the safety-related interruption of a safety circuit.

The bus interface consists of a

}Coupling plug with screw terminals for connecting to a master controller

}Terminator for terminating the PNOZpower bus

It is actuated by

}PNOZmulti range units,

}PSS range output modules,

}PNOZelog range units.

The bus interface may only be used in conjunction with units that evaluate a feedback loop.

The following is deemed improper use in particular:

}Any component, technical or electrical modification to the product

}Use of the product outside the areas described in this manual

}Use of the product outside the technical details (see Technical details [ 10]).

NOTICE

EMC-compliant electrical installation

The product is designed for use in an industrial environment. The product

may cause interference if installed in other environments. If installed in other

environments, measures should be taken to comply with the applicable

standards and directives for the respective installation site with regard to in-

terference.

PNOZ pe2p

Operating Manual PNOZ pe2p

21035-EN-03 6

Safety regulations

Use of qualified personnel

The products may only be assembled, installed, programmed, commissioned, operated,

maintained and decommissioned by competent persons.

A competent person is someone who, because of their training, experience and current pro-

fessional activity, has the specialist knowledge required to test, assess and operate the

work equipment, devices, systems, plant and machinery in accordance with the general

standards and guidelines for safety technology.

It is the company’s responsibility only to employ personnel who:

}Are familiar with the basic regulations concerning health and safety / accident preven-

tion

}Have read and understood the information provided in this description under "Safety"

}And have a good knowledge of the generic and specialist standards applicable to the

specific application.

Warranty and liability

All claims to warranty and liability will be rendered invalid if

}The product was used contrary to the purpose for which it is intended

}Damage can be attributed to not having followed the guidelines in the manual

}Operating personnel are not suitably qualified

}Any type of modification has been made (e.g. exchanging components on the PCB

boards, soldering work etc.).

Disposal

}When decommissioning, please comply with local regulations regarding the disposal of

electronic devices (e.g. Electrical and Electronic Equipment Act).

PNOZ pe2p

Operating Manual PNOZ pe2p

21035-EN-03 7

Unit features

}Actuated via safety contacts or safe semiconductor outputs

}Expansion module control output via PNOZpower bus

}Max. 6 expansion modules can be connected via jumpers

}Plug-in connection terminals

Block diagram/terminal configuration

PNOZpower-BUS

Function Description

The bus interface PNOZ pe2p, in conjunction with the expansion modules, is used to ex-

pand a safety circuit. It is driven from a master controller (e.g. safe outputs on a PSS).

The unit is ready for operation when when supply voltage is applied and the feedback loop

Y1-Y2 is closed

}24 V DC are available at the terminal K1 (e.g. the PSS output has a high signal):

– At the expansion module control output connected to the PNOZpower bus there is a

high signal.

}0 V DC are available at the terminal K1 (e.g. the PSS output has a low signal):

– At the expansion module control output connected to the PNOZpower bus there is a

low signal.

NOTICE

When controlling an expansion module via the den PNOZpower bus the

switch-on delay/delay-on de-energisation of the controlling device and the

expansion module are added together.

Operating modes

}Single-channel operation: no redundancy in the input circuit, earth faults in the start cir-

cuit are detected depending on the master controller.

PNOZ pe2p

Operating Manual PNOZ pe2p

21035-EN-03 8

Installation

}The unit should be installed in a control cabinet with a protection type of at least IP54.

}Connect the bus interface to the first expansion module via the coupling connector.

NOTICE

Always fit a terminator to the first and last device.

}Only use terminators, jumpers and terminals of the modular safety system PNOZpower.

}Layout:

– The PNOZ pe2p is installed on the left of the first expansion module.

}Maximum hardware:

– 1 bus interface

– 6 expansion modules

Expansion module 1 Expansion module 2 Expansion module 6

95579

Terminator

Order no. 779120

95425

Jumper

Order no. 774639

779125

PNOZ pe2p

Coupling connector with

screw terminals

WARNING!

Risk of electrocution!

When voltage is applied, contact with live components could result in seri-

ous or even fatal injury from an electric shock.

The plug-in connection terminals should only be connected and disconnec-

ted when the voltage is switched off.

PNOZ pe2p

Operating Manual PNOZ pe2p

21035-EN-03 9

Wiring

Please note:

}Information given in the "Technical details [ 10]" must be followed.

}Max. cable runs Imax at the input circuit and feedback loop: Short circuits and earth faults

are detected by the master controller. The maximum cable runs is therefore dependent

on the master controller.

}Use copper wire that can withstand 60/75°C.

}Ensure the EMC requirements of IEC 60204-1 are met.

}The bus interface and input circuits of the safety control system/ the safety relay must

always be supplied by a single power supply.

}The power supply must comply with the regulations for extra low voltages with protect-

ive electrical separation (SELV, PELV) in accordance with VDE 0100, Part 410.

Preparing for operation

Supply voltage AC DC

L+

L-

Connection

Control via safety system

(PNOZmulti, PSS) or safety relay

(PNOZelog)

K1Output 24 V DC

Input 24 V DC

24 V DC

0 V

PNOZpower-Bus

Operation

NOTICE

The safety function should be checked after initial commissioning and each

time the plant/machine is changed. The safety functions may only be

checked by qualified personnel.

Signal statuses of the inputs and outputs

}K1: PNOZpower input circuit

– "1" signal (+24 VDC): Expansion modules are actuated

PNOZ pe2p

Operating Manual PNOZ pe2p

21035-EN-03 10

– "0" signal (0 V): Expansion modules are not actuated

}Y2: Feedback loop output

– "1" signal (+24 VDC): Safety contacts of the expansion modules open

– "0" signal (0 V): Safety contacts of the expansion modules closed

Technical details

General

Approvals CCC, CE, EAC (Eurasian), TÜV, cULus Listed

Electrical data

Supply voltage

Voltage 24 V

Kind DC

Voltage tolerance -15 %/+10 %

Residual ripple DC 160 %

Duty cycle 100 %

Inputs

Number 1

Voltage at

Input circuit DC 24 V

Feedback loop DC 24 V

Current at

Input circuit DC 30 mA

Feedback loop DC 1 A

Environmental data

Climatic suitability EN 60068-2-78

Ambient temperature

Temperature range -10 - 55 °C

Storage temperature

Temperature range -25 - 70 °C

Climatic suitability

Humidity 93 % r. h. at 40 °C

Condensation during operation Not permitted

EMC EN 60947-5-1, EN 61000-6-2, EN 61326-3-1

Vibration

In accordance with the standard EN 60068-2-6

Frequency 10 - 55 Hz

Amplitude 0,35 mm

Airgap creepage

In accordance with the standard EN 60947-1

Overvoltage category III

Pollution degree 2

Rated insulation voltage 30 V

Rated impulse withstand voltage 0,8 kV

Inhaltsverzeichnis

Andere Pilz Relais Handbücher

Pilz

Pilz PNOZ X3.2 Bedienungsanleitung

Pilz

Pilz P2HZ X1 Bedienungsanleitung

Pilz

Pilz PNOZ V Bedienungsanleitung

Pilz

Pilz PZE 9P Bedienungsanleitung

Pilz

Pilz PNOZ X2.9P Bedienungsanleitung

Pilz

Pilz PNOZ s2 Bedienungsanleitung

Pilz

Pilz PNOZ 2 Bedienungsanleitung

Pilz

Pilz PZE X4.1P Bedienungsanleitung

Pilz

Pilz PNOZ s4.1 Bedienungsanleitung

Pilz

Pilz PNOZ XV2P Bedienungsanleitung

Pilz

Pilz PNOZ mmc7p CC Bedienungsanleitung

Pilz

Pilz PNOZ X Series Bedienungsanleitung

Pilz

Pilz PNOZ X2P Bedienungsanleitung

Pilz

Pilz PNOZ X6 Bedienungsanleitung

Pilz

Pilz PNOZ e4.1p Bedienungsanleitung

Pilz

Pilz PST 4 Bedienungsanleitung

Pilz

Pilz PNOZ e1vp 10 Bedienungsanleitung

Pilz

Pilz PNOZ e1.1p Bedienungsanleitung

Pilz

Pilz PZE X4VP Bedienungsanleitung

Pilz

Pilz PNOZ XV3.3P Bedienungsanleitung

Pilz

Pilz P1HZ 2 Bedienungsanleitung

Pilz

Pilz PNOZ 16S Bedienungsanleitung

Pilz

Pilz PMD s10 Bedienungsanleitung

Pilz

Pilz S1MO Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung

Littelfuse

Littelfuse SE-330AU Bedienungsanleitung