PIMORONI Speaker pHAT Bedienungsanleitung



Assembling Speaker pHAT

In this guide, you'll learn how to assemble your Speaker pHAT. Speaker pHAT combines an I2S DAC and

mono amplifier, a tiny 8Ω2W speaker, and a 10 LED bar graph that can be used as a VU meter to display

volume levels.

Like our other pHATs, Speaker pHAT comes as a kit, so you'll have to assemble it yourself. Fortunately, it's

really easy to assemble, and shouldn't take you more than 30 minutes. We'll show you just how to do that here.

Mountingthespeaker

The speaker mounts on the underside of Speaker pHAT (the top is the side with the boom box artwork), and

requires a couple of pieces of wire to be soldered from the two solder pads on the speaker to the two pads on

the underside of the pHAT.

We'll mount the speaker with the nuts and bolts first. Push the four bolts through from the top of Speaker

pHAT, using the inner set of four holes (the outer set are for mounting the pHAT).

It's really important to use these spacer nuts. If the speaker isn't spaced slightly off the PCB, then the

Mylar speaker cone will vibrate against the back of the PCB, degrading both the sound quality and the

speaker itself.

Use four of the nuts to secure the bolts on the underside of the pHAT; they'll act as spacers to space the

speaker slightly away from the pHAT.

Now place the speaker on the bolts, ensuring that the solder pads are at the same side as the solder pads on the

pHAT, and secure with the remaining four nuts.

The kit comes with a length of 24 AWG wire, and we'll use it to connect the two terminals of the speaker. Snip

off a couple of pieces of the wire long enough to stretch from the terminals on the speaker to the solder pads on

the pHAT.

First, solder the two pieces of wire to the terminals on the speaker. Make sure that you use a pair of tweezers

preferably, or a small piece of tissue paper will do at a push, to hold the piece of wire and prevent you from

burning yourself. The terminals on the speaker should already have a blob of solder on them, so all you should

have to do is hold your soldering iron on the blob of solder until it melts, then place the piece of wire and

remove your soldering iron, holding the wire in place until the solder cools.

Once you've soldered both ends to the speaker terminals, use your solder to put a couple of blobs of solder on

the two pads on the pHAT. Now, bend the ends of the wires down to the pads and press and hold your

soldering iron until the solder melts and attaches the wire. Add a little extra solder if necessary, and snip off

any excess wire.

Solderingtheheader

Speaker pHAT comes with a female 40 pin header that you'll need to solder to be able to use your Speaker

pHAT with your Pi. We have a guide here that you can follow to learn how to solder headers to pHATs.

Or... you could use one of super-simple hammer headers if you're still not a pro-solderer or you're just a bit

lazy.

https://shop.pimoroni.com/products/move‐mini‐buggy‐kit‐for‐micro‐bit4/17/2017

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PIMORONI Mikrocontroller Handbücher

PIMORONI

PIMORONI OctoCam PIM286 Bedienungsanleitung

Beliebte Mikrocontroller Handbücher anderer Marken

AMS

AMS AS7261 Demo Kit Bedienungsanleitung

Novatek

Novatek NT6861 Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266 SDK Einrichtungshandbuch

Nuvoton

Nuvoton ISD61S00 ChipCorder Leitfaden

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2420DK Bedienungsanleitung

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Bedienungsanleitung

NEC

NEC 78GK0S/K 1+ Series Montage- und Bedienungsanleitung

Mikroe

Mikroe SEMITECH N-PLC Click Montage- und Bedienungsanleitung

Intel

Intel Agilex Bedienungsanleitung

Cypress

Cypress CY4607 HX2VL Bedienungsanleitung

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Bedienungsanleitung

Texas Instruments

Texas Instruments TMS320F2837 D Series Bedienungsanleitung

CYPRES

CYPRES CY14NVSRAMKIT-001 Bedienungsanleitung

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Bedienungsanleitung

Espressif Systems

Espressif Systems ESP8266EX Betriebsanleitung

Abov

Abov AC33M8128L Bedienungsanleitung

Laird

Laird BL654PA Bedienungsanleitung