Pirelli Discus DEX P200H Bedienungsanleitung

FRONT PANEL

LED

Label LED Color LED Behavior

g Green Steady ON: The device is

powered on

OFF: The device is

powered off

e Green/

Yellow/Red

Static

Green:

PLC link Established

with speed is greater

or equal than

threshold 2

(100Mbps)

Static:

Yellow

PLC link Established

with speed is

between threshold 1

(80Mbps) and

threshold 2

(100Mbps)

Static:

Red PLC link Established with speed is below or equal

threshold 1 (80Mbps)

OFF No data received by an associated and

authenticated device on the PLC link

f Green Steady ON: Ethernet Link is established and Ethernet activity

present (traffic in up/down direction)

OFF: No Ethernet Link is established

REAR PANEL

PORTS DESCRIPTION

a AC power plug

d One Ethernet port 10/100 Mbps

BUTTONS DESCRIPTION

b Reset to factory default

c Security button (Authentication Button)

PACKAGE CONTENTS

Your new Discus™ DEX P200H kit contains the related hardware and

software.

In it you will find:

1. Two Discus™ DEX P200H units

2. Two Ethernet cables

3. One installation CD-ROM (Pirelli Device Manager and QIG)

By purchasing your Discus™ DEX P200H, based on PLC technology

compliant with Homeplug AV standard, you have entered into the

word of Broadband Connectivity. DEX P200H Extenders, high

performance and cost effective external dongles, make the Customer

able to connect the Home Gateway to any Ethernet terminal (e.g. Set

Top Box), avoiding un-esthetical new cabling, wiring works and

technical on-site support.

This Quick Installation Guide is meant to help the User installing

Discus™ DEX P200H and distributing Broadband Services (e.g. High

Definition Video Streaming) throughout Home Network, quickly and

easily.

1Positioning the Extenders

You should preferably place the extenders in a position that:

•is not exposed to high moisture and water dropping

•is not exposed to direct sunlight and heat sources

•is not too close to fluorescent lighting fixture and other sources

of electrical noise such as radio sets, transmitters and

amplifiers

NOTE: Nominal performances cannot be guaranteed in presence of

fluorescent lighting fixture and Switching power supply interference !

2System Requirements

Before starting you must ensure the following:

•One avalable 10/100 Mbps Ethernet port

•Windows 2000/XP operating system

NOTE: Previous requirements are suggested for device configuration by

Pirelli Device Manager.

78910

11 12 13 14

3. Connect a standard LAN cable from the one device’s Ethernet port to your Access

Gateway.

4. Wait few seconds to complete startup and then check the LEDs.

•The Ethernet LED should be ON.

If the Led Status is different as defined above, check cable connections.

5. Plug the other DEX P200H into a normal wall socket.

6. Wait few seconds to complete start-up and then check the LEDs.

•The Power LED should be ON.

•The Link LED will be ON if other Powerline devices are detected, otherwise it will be

OFF.

7. Connect a standard LAN cable from the one device’s Etherne

port to your Ethernet terminal (e.g. Set Top Box).

8. Wait few seconds to complete start-up and then check the LEDs.

•The Ethernet LED should be ON.

If the Led Status is different as defined above, check cable

connections.

NOTE: DEX P200H devices should communicate automaticall

thanks to factory default configuration

HOW TO ASSOCIATE THE DEVICES

FIRST SCENARIO

This procedure describes how to associate two un-associated devices.

Two un-associated adapters (a,b) are forming a new network (Network AB).

The procedure is as follows:

1. Press the security button on the adapter (A) for less than 3 seconds.

2. Press the security button on the adapter (B) for less than 3 seconds.

3. The Power LEDs start to flash.

fter a few seconds the reboot procedures and after that the Powe

and PLC link LEDs should be on.

5. The configuration is successful.

NOTE: If the procedure fails:

1. Press and hold authentication button on the adapter (A) fo

at least ten seconds, until the power LED goes out and star

to flash (added).

2. Press and hold authentication button on the adapter (B) fo

at least ten seconds , until the power LED goes out and star

to flash (added).

ssociate the devices again following the procedure

described above.

SECOND SCENARIO

Join an unassociated adapter (C) to an existing network (Networ

AB).

The procedure is as follows:

1. Press the security button on the adapter A (or B) for less than 3

seconds.

2. Press the security button (c) on the adapter (C) for less than 3

seconds.

3. The Power LEDs start to flash.

4. After a few seconds, the Power and PLC link LEDs should be on.

5. The configuration is successful.

NOTE: If the procedure fails:

1. Press and hold authentication button on the adapter (C) fo

at least 10 seconds, until the power LED goes out and star

to flash (added).

ssociate the devices again following the procedure

described above.

3Connecting the Extenders

1. Plug the DEX P200H into a normal wall socket.

Connect PLC Adapter into power strip or surge protectors may degrade network performance.

2. Wait few seconds to complete startup and then check the LEDs.

•The Power LED should be ON.

•The Link LED will be ON if other Powerlinedevices are detected,

HOW TO RESET THE DEVICES

1. Press the reset button (d) the adapter A for 2 seconds.

2. The adapter starts the reboot procedure. All LEDs should be ON.

3. After a few seconds, the Power and PLC link LEDs should be

ON. The reset procedure is finished successfully.

Andere Pirelli Extender Handbücher

Pirelli

Pirelli PLITOEB0911 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung