Pitsco Education Wind Gen Plus Kit Bedienungsanleitung

59739 V0421

Cautionary and Warning Statements

• This kit is designed and intended for educational purposes only.

• Use only under the direct supervision of an adult who has read and

understood the instructions provided in this user guide.

• Read warnings on packaging and in manual carefully.

• Always exercise caution when using sharp tools.

User Guide

Wind Gen

Plus Kit

2 Wind Gen Plus Kit User Guide 59739 V0421

Materials Included

Building the Wind Generator

1. On the area where you intend to work,

spread a piece of waxed paper and tape it

down to the surface. This will prevent glue

from getting on the work surface.

2. Using scissors or a hobby knife, carefully

cut out the circles and the blades from the

card-stock sheet (Figure 1). Cut out the small

circle in the middle of each card-stock circle.

3. Carefully pop out the laser-cut parts from

the wooden sheet. Find the three Part 6s

and one Part 5. Set aside all the other parts.

4. Glue the rounded end of each Part 6 into

one of the holes around the perimeter of

Part 5 (Figure 2).

5. When dry, glue a card-stock circle centered

over Part 5. Press it rmly down and turn it

over. Repeat with the other circle (Figure 2).

6. Glue each blade to the face of each Part 6.

Make sure the printed side of the blades is

facing down and the straight side is aligned

with the edge of the Part 6s (Figure 3). Let

dry.

7. Find Parts 2, 3, and 4. Glue the two Part 3s

on top of Part 2 (Figure 4).

8. Glue Part 4 onto Part 2 in the slot under

the Part 3s (Figure 5). Center this part in the

opening of Part 2 and make sure it is set in

place by sliding it as far up into the slot as

possible.

• 1 sheet card-stock circles and

blades

• 1 piece of small tubing

• 1 motor with LED

• 1 rubber band

• 1 sheet of wooden laser-cut parts

• 1 prop hub

Items Required (not included)

• HD Bond II or wood glue

• Waxed paper

• Masking tape

• Scissors or hobby knife

• Electric fan or source of wind

Figure 1

GLUETHIS SIDE

WIND GENERATOR BLADES

GLUETHIS SIDE

Figure 2

Card-stock circle

Figure 3

Blades

Wind Gen Plus Kit User Guide 59739 V0421 3

9. Glue the other end of Part 2 into Part 1

(Figure 6); this makes the stand. Let it dry.

10. Place the motor on top of the stand with the

motor post facing toward the straight edge

of Part 1 (Figure 7). Loop one end of the

rubber band over one side of Part 4, pull it

over the motor, and hook the other end on

the other side (Figure 8).

11. When the blades are dry, take the blade

assembly and create a scoop shape (Figure 9).

Repeat this for all three blades.

12. Attach the prop hub onto the motor shaft

and carefully press the blade assembly onto

the shaft, using the prop hub to ensure

proper alignment of the parts (Figure 10). Be

sure the unprinted side of the assembly is

facing forward.

13. Slide a small piece of tubing over the end of

the prop hub.

Figure 6Figure 5

Figure 7

Motor Rubber

band

Figure 8

Rubber

band

Figure 9 Figure 10

Figure 4

4 Wind Gen Plus Kit User Guide 59739 V0421

P.O. Box 1708 • Pittsburg, KS 66762

www.pitsco.com

Toll-Free Orders 800-835-0686

Using the Wind Gen Plus

1. Set the Wind Gen Plus in front of a fan. It is recommended to secure it

to the table or oor with masking tape to keep it from blowing over.

2. Turn on the fan to a low setting, making sure the wind generator is

close to the fan and in the middle of the airow. If the wind generator

does not turn, set the fan to a higher setting.

3. Watch as the Wind Gen Plus starts to turn and lights the LED.

Experiments

• Use a multimeter to measure the voltage at dierent wind speeds and

record the results in a data table. Graph the results.

• Describe how a large-scale wind farm could provide power for homes

and industry.

Completed model

Andere Pitsco Education Lehrmittel Handbücher

Pitsco Education

Pitsco Education Wheel Lathe Bedienungsanleitung

Pitsco Education

Pitsco Education DRONE ARENA Bedienungsanleitung

Pitsco Education

Pitsco Education TETRIX MAX Bedienungsanleitung

Pitsco Education

Pitsco Education TETRIX MAX R/C Motor Controller Bedienungsanleitung

Pitsco Education

Pitsco Education FLO Bedienungsanleitung

Pitsco Education

Pitsco Education BUILDERSPACES SPACEPORT Bedienungsanleitung

Pitsco Education

Pitsco Education Desk Jockey Bedienungsanleitung

Pitsco Education

Pitsco Education R2K Rocket Kit Bedienungsanleitung

Beliebte Lehrmittel Handbücher anderer Marken

DISCOVER

DISCOVER talking pen Bedienungsanleitung

pitsco

pitsco Smart Buddies 45895 Bedienungsanleitung

RS 3.5 Bedienungsanleitung

Quanser

Quanser QNET 2.0 Bedienungsanleitung

CAE Healthcare

CAE Healthcare METIman Bedienungsanleitung

Turning Technologies

Turning Technologies Pulse Bedienungsanleitung

fischertechnik

fischertechnik STEM Coding Pro Bedienungsanleitung

Experia

Experia IRiS Light Wand Bedienungsanleitung

Sphero

Sphero RVR RV01 Bedienungsanleitung

Limbs & Things

Limbs & Things 60905 Bedienungsanleitung

JP TURN Connect T101 Bedienungsanleitung

TruCorp

TruCorp AirSim Advance Bedienungsanleitung

LeapFrog

LeapFrog Mr. Pencil's Scribble, Write & Read Bedienungsanleitung

ScienTECH

ScienTECH 2261 Bedienungsanleitung

Rompa

Rompa 20019 Bedienungsanleitung

Duinotech

Duinotech XC4322 Bedienungsanleitung

Enabling Devices

Enabling Devices Spinning Light Show Bedienungsanleitung

Adam,Rouilly

Adam,Rouilly AR253 Bedienungsanleitung