Pittsburgh 98059 Bedienungsanleitung

Bench Top Digital Scale

Item 98059 - 33 LB. Weight Capacity

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

When unpacking, make sure that the product is intact and undamaged.

If any parts are missing or broken, please call 1-800-444-3353 as soon as possible.

Visit our website at: http://www.harborfreight.com

or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.

Not legal for trade or postage.

Manual Revised 11d

Page 2SKU 98059 For technical questions, please call 1-800-444-3353.

Specications

Electrical

Requirements

Input: 120 VAC~ / 60 Hz

Output: 9 VDC @ 500mA

Battery Type: 6V4ah/20HR

Battery Charge Time: 8 ~ 10 Hours

Adapter Plug: 2 Prong, Grounded

Power Switch: ON/Off Rocker Switch

Maximum

Weight

Capacity

33 Pounds (15 Kilograms)

Minimum

Weight 7 ounces/200 grams

Control

Panel Button

Indicators

Yellow Push Button = Lb. or Kg.

Blue Push Button = Tare

Blue Push Button = Zero

Red LED

Indicators

T = Tare / Z = Zero

LB = Pound / KG = Kilogram

AC = AC Powered

Additional

Features

Four Plastic Feet for Leveling of

Scale

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions: (1) This device may not

cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

Save This Manual

Keep this manual for the safety warnings

and precautions, assembly, operating, inspection,

maintenance and cleaning procedures. Write the

product’s serial number in the back of the manual near

the assembly diagram (or month and year of purchase

if product has no number). Keep this manual and the

receipt in a safe and dry place for future reference.

Important Safety Information

In this manual, on the labeling, and all other

information provided with this product:

This is the safety alert symbol. It is

used to alert you to potential

personal injury hazards. Obey all

safety messages that follow this

symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if

not avoided, will result in death or serious injury.

WARNING indicates a hazardous situation which, if

not avoided, could result in death or serious injury.

CAUTION, used with the safety alert symbol,

indicates a hazardous situation which, if not

avoided, could result in minor or moderate injury.

NOTICE is used to address practices

not related to personal injury.

CAUTION, without the safety alert symbol, is used

to address practices not related to personal injury.

General Power Tool

Safety Warnings

WARNING Read all safety warnings and

instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/

or serious injury.

Save all warnings and instructions for future

reference.

The term ″Scale″ in the warnings refers

to your battery-operated (cordless)

Bench Top Digital Scale.

1. Work area safety

a. Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b. Do not operate the Scale in explosive

atmospheres, such as in the presence

of ammable liquids, gases or dust.

Battery operated equipment create sparks

which may ignite the dust or fumes.

2. Electrical safety

a. The AC/DC Adapter plug must match the

outlet. Never modify the plug in any way. Do

not use any additional adapter plugs with

the Scale. Unmodied plugs and matching

outlets will reduce risk of electric shock.

b. Avoid body contact with grounded surfaces

such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is grounded.

c. Do not expose the Scale to rain or wet

conditions. Water entering the Scale will

increase the risk of electric shock.

d. Do not abuse the AC/DC Adapter Cord.

Never use the Cord for carrying, pulling

or unplugging the AC/DC Adapter. Keep

the Cord away from heat, oil, sharp edges

or moving parts. Damaged or entangled

Cords increase the risk of electric shock.

e. When operating the Scale outdoors, use

an extension cord suitable for outdoor

Page 3SKU 98059 For technical questions, please call 1-800-444-3353.

use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

f. If operating the Scale in a damp location

is unavoidable, use a Ground Fault Circuit

Interrupter (GFCI) protected supply. Use of

a GFCI reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use

common sense when operating the Scale. Do

not use the Scale while you are tired or under

the inuence of drugs, alcohol or medication.

A moment of inattention while operating the

Scale may result in serious personal injury.

b. Use safety equipment. Always wear

eye protection. Safety equipment

such as ANSI-approved safety impact

goggles will reduce personal injuries.

c. Prevent unintentional starting. Ensure the

Power Switch (11) is in the off-position before

connecting to power source and/or battery

pack, picking up or carrying the tool. Carrying

battery operated equipment with your nger on

the Power Switch or energizing equipment that

have the Power Switch on invites accidents.

d. Do not overreach. Keep proper footing

and balance at all times. This enables better

control of the Scale in unexpected situations.

4. Scale use and care

a. Do not force the Scale. Use the correct

Scale for your application. The correct

Scale will do the job better and safer at

the rate for which it was designed.

b. Do not use the Scale if the Power Switch (11)

does not turn it on and off. Any equipment

that cannot be controlled with the Power

Switch is dangerous and must be repaired.

c. Disconnect the AC/DC Adapter Cord

before making any adjustments, changing

accessories, or storing the Scale. Such

preventive safety measures reduce the risk

of starting the equipment accidentally.

d. Store idle battery powered equipment

out of the reach of children and do not

allow persons unfamiliar with the Scale

or these instructions to operate the

equipment. Battery powered equipment are

dangerous in the hands of untrained users.

e. Maintain the Scale. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the Scale’s

operation. If damaged, have the Scale repaired

before use. Many accidents are caused by poorly

maintained battery operated power equipment.

f. Use the Scale in accordance with these

instructions, taking into account the working

conditions and the work to be performed. Use

of the Scale for operations different from those

intended could result in a hazardous situation.

5. Battery tool use and care

a. Recharge only with the AC/DC Adapter (25)

specied by the manufacturer. An Adapter that

is suitable for one type of Battery may create a

risk of re when used with another Battery Pack.

b. Use this Scale only with specically

designated Batteries. Use of any other

Battery may create a risk of injury and re.

c. When the Battery (21) is not in use, keep it

away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal

objects, that can make a connection from

one terminal to another. Shorting the Battery

Terminals together may cause burns or a re.

d. Under abusive conditions, liquid may be

ejected from the Battery (21). If contact with

liquid from the battery accidentally occurs,

ush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected

from the Battery may cause irritation or burns.

6. Service

a. Have your Scale serviced by a qualied

repair person using only identical

replacement parts. This will ensure that

the safety of the equipment is maintained.

Specic Safety Warnings

1. Maintain labels and nameplates on the tool.

These carry important safety information. If

unreadable or missing, contact Harbor

Freight Tools for a replacement.

2. This Scale contains a sealed lead Battery. Do not

dispose of an old Battery in re to avoid explosion

and possible personal injury. Recycle old batteries

according to local solid waste authority procedures.

3. Do not exceed the Scale’s maximum

weight capacity of 33 pounds.

4. Avoid unintentional starting. Prepare to

begin work before turning on the Scale.

5. Do not leave the Scale unattended when it’s AC/

DC Adapter is plugged into an electrical outlet.

Turn off the equipment, and unplug the AC/DC

Adapter from its electrical outlet before leaving.

6. The AC/DC Adapter gets hot during

use. The Adapter’s heat can build up

to unsafe levels and create a re

hazard if it does not receive adequate

ventilation, due to an electrical fault,

or if it is used in a hot environment.

Do not place the Adapter on a ammable surface.

Especially avoid placing the Adapter on carpets

and rugs; they are not only ammable, but they

Page 4SKU 98059 For technical questions, please call 1-800-444-3353.

also obstruct air ow under the Adapter. Place

the Adapter on a stable, solid, nonammable

surface (such as a stable metal workbench or

concrete oor) at least 1 foot away from all

ammable objects, such as drapes or walls. Keep

a re extinguisher and a smoke detector in the

area. Frequently monitor the Adapter and Battery

during use.

7. This product is not a toy. Keep it

out of reach of children.

8. People with pacemakers should consult their

physician(s) before use. Electromagnetic elds in

close proximity to heart pacemaker could cause

pacemaker interference or pacemaker failure. In

addition, people with pacemakers should:

• Avoid operating alone.

• Properly maintain and inspect to avoid electrical

shock.

• Any power cord must be properly

grounded. Ground Fault Circuit Interrupter

(GFCI) should also be implemented – it

prevents sustained electrical shock.

9. The warnings, precautions, and instructions

discussed in this instruction manual cannot

cover all possible conditions and situations

that may occur. It must be understood by the

operator that common sense and caution are

factors which cannot be built into this product,

but must be supplied by the operator.

SAVE THESE

INSTRUCTIONS.

Grounding

TO PREVENT ELECTRIC

SHOCK AND DEATH FROM

INCORRECT GROUNDING

WIRE CONNECTION:

Check with a qualied electrician if you

are in doubt as to whether the outlet is

properly grounded. Do not modify the

Adapter Cord Plug provided with the tool.

Never remove the grounding prong from

the Plug. Do not use the Adapter if the

Cord or Plug is damaged. If damaged,

have it repaired by a service facility before

use. If the Plug will not t the outlet, have

a proper outlet installed by a qualied

electrician.

Double Insulated Tools: Tools

with Two Prong Plugs

Outlets for 2-Prong Plug

Tools marked “Double Insulated” do not require

grounding. They have a special double insulation

system which satises OSHA requirements

and complies with the applicable standards of

Underwriters Laboratories, Inc., the Canadian

Standard Association, and the National Electrical

Code.

(See Outlets for 2-Prong Plug.)

2. Double insulated tools may be used in either of the

120 volt outlets shown in the preceding illustration.

(See Outlets for 2-Prong Plug.)

Extension Cords

1. Grounded tools require a three wire extension

cord. Double Insulated tools can use

either a two or three wire extension cord.

2. As the distance from the supply outlet increases,

you must use a heavier gauge extension cord.

Using extension cords with inadequately sized wire

causes a serious drop in voltage, resulting in loss

of power and possible tool damage.

The smaller the gauge number of the wire, the

greater the capacity of the cord. For example,

a 14 gauge cord can carry a higher current

than a 16 gauge cord. (See Table A.)

Page 5SKU 98059 For technical questions, please call 1-800-444-3353.

3. When using more than one extension cord

to make up the total length, make sure

each cord contains at least the minimum

wire size required. (See Table A.)

4. If you are using one extension cord for more

than one tool, add the nameplate amperes

and use the sum to determine the required

minimum cord size. (See Table A.)

5. If you are using an extension cord outdoors, make

sure it is marked with the sufx “W-A” (“W” in

Canada) to indicate it is acceptable for outdoor use.

6. Make sure the extension cord is properly wired

and in good electrical condition. Always replace

a damaged extension cord or have it repaired

by a qualied electrician before using it.

7. Protect the extension cords from sharp objects,

excessive heat, and damp or wet areas.

RECOMMENDED MINIMUM WIRE

GAUGE FOR EXTENSION CORDS*

(120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25’

50’

75’

100’

150’

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

TABLE A

* Based on limiting the line

voltage drop to ve volts at

150% of the rated amperes.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~ Volts Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute

(RPM)

Page 6SKU 98059 For technical questions, please call 1-800-444-3353.

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY

INFORMATION section at the beginning of

this manual including all text under

subheadings therein before set up or use

of this product.

TO PREVENT SERIOUS

INJURY FROM ACCIDENTAL

OPERATION:

Turn off and unplug the unit before

performing any inspection, maintenance,

or cleaning procedures.

Scale Set Up

1. Always place the Scale on a clean, dry, at, level

workbench capable of supporting the weight

of the Scale and all objects to be weighed.

2. The workbench area must be free of

vibration, strong air currents, direct

sunshine, and high temperatures.

3. To level the scale before use:

d. Turn the scale upside down.

e. Rotate the Leveling Feet (15) clockwise until they

are fully recessed. Then turn counterclockwise

three full turns. Hold each foot and rotate the

locking nut two full clockwise turns or until

the locking nut is not tightened on the foot.

f. Turn the scale right side up and place on the

work surface. Use the built-in leveling bubble

at the front left hand side of the Scale to check

if the scale is level. Rotate the feet individually

until the leveling bubble is centered.

g. When the scale is level, secure each foot in place

by turning its locking nut counterclockwise until

tight. Re-check the level, and re-adjust the feet if

necessary. The scale is now set for operation.

8. Check that the Scale’s Platform (1) will

not come in contact with any object before

or during the weighing process.

9. Route the AC/DC Adapter (25) Cord along

a safe route to reach the workbench

area without creating a tripping hazard or

exposing the Cord to possible damage.

Charging the Battery

AC/DC ADAPTER CORD

(25)

POWER SWITCH

(11)

CHARGING INPUT PORT

LEVELING FOOT

(15)

FIGURE A

(BOTTOM VIEW)

To charge the Battery (21) of the Scale, insert

the AC/DC Adapter (25) Cord into the Charging

Input Port located on the underside of the

Scale. Make sure the Power Switch (11) is

in its “OFF” position throughout the charging

process. Plug the AC/DC Adapter into the

nearest 120 volt, grounded, electrical outlet.

IMPORTANT: The charge time for the Battery is 8 to 10

hours. Do not overcharge the Battery to avoid

damage to the Battery and/or AC/DC Adapter.

When nished charging, unplug the AC/DC Adapter

from its electrical outlet. Then unplug the Cord

from the Charging Input Port of the unit.

Page 7SKU 98059 For technical questions, please call 1-800-444-3353.

Operating the Scale

Components and Controls

SCALE LEVEL

(26)

“ZERO”

WEIGHT WINDOW

“TARE”

”UNIT”

PLATFORM (1)

ZERO

TARE KILOGRAMS

POUNDS

AC POWER

FIGURE B

Refer to the above photos for the following

instructions. The function buttons (Tare,

Unit and Zero) are on the right side of the

front of the Scale. The indicator lights on

either side of the Weight Window display

information about the Scale’s settings.

Turning on the Scale

Turn the Power Switch (11) to its “ON” position.

The Scale will do a self-check, during which

you can determine whether the Weight Window

and Zero functions are working normally.

Reset Weight to Zero

1. The “ZERO” Indicator Light is located at the

bottom/left of the Weight Window (See Figure

B). Once the Scale is turned on, it will illuminate

to indicate the Scale is at the ZERO position.

2. If the Weight Window does not display

“0.000” before you weigh an object, and

the zero range is less than 60g, press

the “ZERO” key. Begin weighing when

the Weight Window displays “0.000”.

Change Units of Measure

1. Press the “UNIT” button to switch between

the measurement unit settings. The Kg

(Kilogram) and LB (Pound) indicator lights

are located to the right of the Weight

Window, indicate which setting is current.

Set Container to Zero before Weighing

The Tare button is used to reset the scale to

zero when an empty container is set on the

scale, and the container is not included in

the weight of the objects to be weighed.

1. The “TARE” Indicator Light is located at the

top/left of the Weight Window (See Figure B).

Once the Scale is turned on, it will illuminate

to indicate the TARE weight is cleared.

2. To weigh objects in a container, but not include

the container weight, place an empty container on

the Platform (1) of the Scale. Press the “TARE”

button and wait for the Weight Window to display

“0.000”, indicating the Scale is ready for weighing.

Place the objects into the container, and the Weight

Window will display the weight of the objects.

Turning off the Scale

1. To turn off the Scale, simply turn the Power

Switch (11) to its “OFF” position.

2. Always make sure to store the Scale in

a clean, dry, safe location out of reach of

children and other unauthorized persons.

Note: Disconnect charger. Do not store the

scale with anything on top of it.

Page 8SKU 98059 For technical questions, please call 1-800-444-3353.

Maintenance and Servicing

Procedures not specically explained in this manual must

be performed only by a qualied technician.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Turn the Power Switch of the Scale to its “OFF” position and unplug the unit’s AC/DC

Adapter from its electrical outlet before performing any inspection, maintenance, or

cleaning procedures.

TO PREVENT SERIOUS INJURY FROM EQUIPMENT FAILURE:

Do not use damaged equipment. If abnormal noise or erratic values

are shown, have the problem corrected before further use.

Inspection, Maintenance, and Cleaning

1. BEFORE EACH USE, inspect the general condition of the Scale.

2. BATTERY REPLACEMENT: A Battery that fails to accept a charge is an indication the Battery

should be replaced. To replace the Battery requires the use of a soldering tool and specic

soldering expertise. It is recommended that only a qualied service technician perform a Battery

replacement procedure. Note: Battery must be fully discharged prior to any soldering.

3. AFTER USE, clean all external surfaces of the Scale with a soft, clean

cloth. Do not use solvents. Do not immerse the Scale in liquid.

4. WARNING! If the Cord of the AC/DC Adapter is damaged, it must

be replaced only by a qualied service technician.

Page 9SKU 98059 For technical questions, please call 1-800-444-3353.

DISPLAY MEANING ACTION TO BE TAKEN

-------------------------------

----

(Mid horizontal line)

A long period display. The ZERO position is

unstable.

Work area too windy or too damp. Move Scale to

a calm, dry work area.

-------------------------------

----

(Upper horizontal line)

The ZERO position is too high. Have a qualied service technician service Scale.

Lower horizontal line

-------------------------------

----

The ZERO position is too low. Have a qualied service technician service Scale.

(Alarm sound) Voltage is lower than 4.8 +/-- 0.1V Recharge or change Battery.

(Alarm sound) Overload. Immediately remove object(s) being weighed. Do

not exceed 33 LB. maximum weight capacity.

(Alarm sound) Circuit integrator faulty. Have a qualied service technician service Scale.

Troubleshooting

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN

THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY

REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY

REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.

IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS

REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE

BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION

OF REPLACEMENT PARTS THERETO.

Page 10SKU 98059 For technical questions, please call 1-800-444-3353.

Parts List & Assembly Diagram

Part # Description Qty

1Platform 1

2Back Label 1

3Top Housing 1

4Bolt (M6 x 25) 2

5Top Support 1

6Sensor 1

7Bottom Support 1

8Bolt (M5 x 12) 4

9Bottom Housing 1

10 Bolt (M4 x 18) 4

11 Power Switch 1

12 Fuse Holder 1

13 10W Adapter 1

Part # Description Qty

14 Bolt (M3 x 16) 2

15 Foot 4

16 Adjuster 1

17 Switch Label 1

18 Circuit Board 1

19 Bolt (M3 x 6) 2

20 Face Label 1

21 Battery 1

22 Battery Cover 1

23 Mike 1

24 Bolt (m8 x 30) 2

25 AC/DC Adapter 1

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and

are not available individually as replacement parts.

2 3

Inhaltsverzeichnis

Andere Pittsburgh Skala Handbücher

Pittsburgh

Pittsburgh 95364 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung