Pivot Mega RAIZIN Bedienungsanleitung

FEATURES

INSTALLATION PROCEDURE

Double-sided

Tape 3

M6 Nut 2 User’s Guide

•Do not work in areas where there is excessive exhaust

Due to vehicle exhaust emission poisoning or fire may result in a damage

to humans.

•Do not crush the cable

Please do not place the unit or the wires in any place that is exposed to

high temperature nor near any rotating objects such as a fan or belt.

Wires may become broken causing a short and/or fire. Do not splash

water on the unit.

•

Safety Precautions for Installation and Checking Operations

When the key is switched to ON, there is a possibility that the fan or belt

may suddenly begin moving and cause bodily injury. When doing any

work, make sure that the key is switched to OFF and when checking

operation make sure not to put your face or hands in a close position

which could cause bodily injury.

•Please securely fasten the product to a stable place

Make sure to install and fasten the unit to a safe place that will not

become entangled in a fan or belt.

•This product is for DC12V cars;

installation cannot be carried out on cars with other voltage

batteries.

•Do not allow water to come into contact with the unit.

The unit has been processed for water resistance but do not splash

with water when washing the car and so on.

CAUTION Improper use or disregard of these warnings may result in the injury or death of people.

Voltage Stabilizer

Our newly designed three-fold (compared to Blue Raizin) large capacity condenser

and our newly designed filter circuitry results in decreases in both circuitry noise

and high frequency impedance which results in a more stable supply of voltage to

the ignition coil and all electronic devices as well as improvements in power loss.

A World's First: View Battery Performance via Lowest Voltage Display

Displaying two types of voltage, both "Real" and "Lowest" Voltage (world first) at

engine start makes it easy to see battery life and loss in battery performance. This

also helps to protect against trouble caused by shortages in voltage to various

electronic devices.

•About Improved Performance......Installation of this product will lead to improvement in electrical aspects of your automobile but due to actual car and driving conditions

these improvements may be negligible or in some cases no change will occur.

•About Judging Battery Life......Depending on the characteristics of the battery itself even a small change in the lowest voltage reading may signal the end of a battery's life.

1.The unit assesses battery performance through changes in lowest voltage readings and when it has been judged to be reduced allows the user to take

necessary measures to improve performance (replacement, recharging, etc...) and thereby provide voltage stability to all electronic devices.

2.The condenser circuitry reduces electrical noise and provides a stable voltage supply to the ignition coil as well as all other electronic devices.

.Wrenches (Socket Wrench .Combination Wrench)

.Vinyl Electrical Tape .Cloth .Absorbing Agent

Things to prepare

WARNING

Digital

Display

BASIC WIRING If an earth terminal is installed...

Make sure that and are connected correctly.

To prevent making any mistakes with the

and and causing a short during installation,

please make sure to insulate.

Remove the cable from the battery terminal.

Insulate the battery terminal with vinyl tape.

Insulate with

vinyl tape.

Ex) The top or side of the battery or any other

flat surface near the battery. (fuse box, etc...)

.Without forcing, make sure you can connect

the two cables to the correct terminals.

.Make sure the installation place is a flat

surface where the unit can be fixed with

double-sided tape.

If you're installing on the top surface,

make sure the car hood will not to

hit the unit when closed.

If you're installing on the side surface, install so

that the cables go out the bottom.

If the cover does not insulate properly, please use

vinyl tape to ensure proper insulation.

Connect the Cable

Remove the vinyl tape from the terminal of the battery.

Connect the minus cable (with blue cap) to the battery's minus terminal.

If the wiring has been completed correctly the voltage should appear and after ten seconds

automatically shut off.

Please make sure to check about connecting the and

cables. Mixing these up will cause damage to the product.

Due to characteristics of the product, upon

contact of the RAIZIN'S to the battery's

or upon the shorting of the flow of

current sparks may be emitted. This is not a defect.

WARNING

NOTE

.If you install with the cables

going out the top, water

may enter the unit and

cause damage. Make sure

to install with cables

going out the

bottom of the unit.

Do not to install in areas subject to water.

Circuitry has waterproof coating. But do not to install in areas subject to water or spray

with water.

Waterproof Sheeting, etc.

CLEAN TO REMOVE

OIL & DUST

If an earth terminal is installed, connect the cable to the terminal.

(See [BASIC WIRING])

Stabilize Voltage and Know when Battery Performance is Reduced !

Sparking upon Contact

USER'S GUIDE

Voltage Stabilizer

Mega RAIZIN

Main Unit

(VS-M As of March, 2008 No.2)

Please check the contents of the package.

Thank you for purchasing PIVOT “Mega RAIZIN”. Please read these instructions carefully

before installing or using this device. Please do not lose this user’s guide, as you will held liable

for the cost of reissuing it.

.Fasten with an M6 nut to the original bolt.

.Fasten between the original nut and the terminal.

Replace the cover after completing the connection.

Properly connect the cable terminal to the battery

terminal.

Connect the unit's cable (one with blue colored

insulation cap) to the terminal of the battery cable.

CAUTION

Please install safely and surely by following these

instructions.

In particular, please be very careful about

connecting the and cables. Mixing these up

will cause damage to the product.

M6 Nut

Battery terminal

Battery

terminal

Cable terminal

Cable

Battery terminal

Battery

terminal

Cable

RAIZIN

Unit

Blue Colored

Insulation Cap

Red Colored

Insulation Cap

Red Colored

Insulation Cap

Earth Terminal

Battery terminal

Installation Preparation

Cable terminal

Battery terminal

Installing the RAIZIN unit.

Decide installation place.

.Do not allow water to come

into contact with the unit.

If it is a good chance of water

coming into contact, please

cover with waterproof

sheeting.

1.If you're installing on the side surface, the double-sided

tape will take about two hours to become secure.

During that time do not allow any vibration to the unit.

2.Reinstalling will cause the tape's adhesive strength to

weaken, so please do not to it.

Clean off all oil and dirt from the bottom of the main

unit and affix the double-sided tape included in the kit.

Clean off all oil and dirt from the installation place and

fasten the main unit.

Remove the cover from the terminal of the battery.

Connect the unit's cable (one with red colored

insulation cap) to the terminal of the battery cable. Original Bolt

M6 Nut

Blue Colored

Insulation Cap

Original Bolt

Connect the unit's cable

Check Wiring

Connect the Cable

Arranging the Cables Arrange the cables with the lock ties included.

.Fasten with an M6 nut to the original bolt.

.Fasten between the original nut and the terminal.

Results you can

count on

.If voltage is not displayed = please check the connection and make sure and

are correct.

Mega

High Capacity System & Battery Performance Monitor

0 5 10 20 (S)

Voltage(V) ACC IG ON Engine Start

Lowest Voltage

New Battery

Ex : 7.5V

Real Voltage

Normal Range

1~1.5V

Engine Running

Reduced Battery

Performance

(Check Required)

ASSESSING BATTERY PERFORMANCE

HOW TO CHECK VOLTAGE

Judging Reduced Battery Performance (Lowest Voltage)

Judgments about reduced battery performance (life) can be made by checking the lowest voltage reading for a new battery at engine start and using that

reading for comparison. In order to do this, this unit measures and displays lowest voltage at engine start and thereby helps to prevent the following troubles

associated with reduced battery performance.

About Judging Reductions in Performance from Changes in Voltage

If the difference in lowest voltage measurements for a new battery falls

1V to 1.5V , the battery's performance can be deemed to be reduced and

we strongly suggest taking the battery to a repair shop for checking and

recharging.

When the engine is started, two types of voltage measurement (lowest voltage at engine start and real voltage) will be displayed for a

short time (about one minute) and then will automatically shut off.

If you wish to re-measure the lowest voltage at engine start please perform only after the display has automatically turned off.

Note that if you are using a remote control starter to start your engine, the display will turn off after about one minute

and cannot be viewed.

Note that this method can only provide a rough

guideline and battery life varies greatly depends on the

individual characteristics of batteries and automobiles.

Also note that even with properly working batteries, large

reductions (about 1V) in lowest voltage readings can occur

when outside temperatures are low (below 5 ) or starting

after having forgotten to turn off the lights.

Note that this measurement method can only provide a

rough guideline and that lowest voltage readings and battery

life varies greatly depending on the individual characteristics

of the battery being used.

By "new battery" we mean a battery that has not been used for more than six

months; if a battery has been used for more than six months a change of

0.5V to 0.8V should be viewed as a sign that performance has been

reduced and the battery should be checked.

Please have battery checked periodically (every

month) or if the following occurs:

.The engine seems not to start well

.The lights seem dark .The battery frequently dies out

Checking while Engine is Running (Real Voltage)

If voltage falls outside an acceptable range while the engine is running one of the following may be the reason and a check should be carried out.

The lowest voltage at engine start is measured and if a change (lower measurement) is detected the battery's performance and life will be

judged to have been reduced.

Possible Causes

Reduced electronic device output caused by unstable voltage supply.

Reduced electronic device output caused by increased noise.

Reduced output due to lack of battery charge.

Trouble

Poor mileage, reduced torque, poor starting, sound and reduced light brightness.

Reductions in mileage and torque as well as in sound quality due to increase in noise.

Troubles in starting engine and dead batteries.

If it is too high (15V or more)

1. The fan belt is too loose or is torn.

2. The alternator or battery does not work properly.

Deterioration in mileage, torque, starting, sound and light brightness.

Engine Start Check the Lowest

Voltage of New Battery Periodic Check

0.7V reduction since new

Ex : 7.5V (Blink) Ex : 6.8V (Blink)

Ex : 5.4V (Blink)

Check

Usable

Engine Start Voltage Displays (Displayed alternately for about sixty seconds)

Lowest

Voltage (3 Seconds) Lowest

Voltage (3 Seconds)

Real

Voltage (5 Seconds)

Real

Voltage (5 Seconds)

After 60 seconds

Ex : 7.5V (Blink) Ex : 7.5V (Blink)Ex : 14.2V (Light up) Ex : 13.8V (Light up)

Automatically

turned off

2.1V reduction since new

Judgment Method

Measurement Method

PIVOT CORPORATION 87-3, Shimookada Okada, Matsumoto-shi, Nagano, 390-0313 Japan TEL0263-46-5901 http://pivotjp.com/

The alternator is broken (Regulator)

Lowered performance of electronic devices or reduced battery life.

Possible

Causes

Trouble

If it is too low (11.5V or less)

Possible

Causes

Trouble

Reductions in

Performance

Normal

After 60

seconds

Inhaltsverzeichnis

Andere Pivot Stromversorgung Handbücher

Pivot

Pivot ATLAS Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung