Pixel RF PRO-1B Bedienungsanleitung
RF PRO-1B INSTALLATION INSTRUCTIONS
This active magnetic loop antenna is designed for reception of signals over the range of 50 kHz to 30 MHz. It
includes a very high dynamic range low-noise preamplier that can be mounted to a pole or any at surface. The
preamplier is designed for minimum intermodulation distortion in the presence of very high level signals that would
normally overload most ampliers. For proper operation the preamplier needs to be powered as shown in the
diagram shown in Figure 1 with the supplied power inserter and power supply that duplexes DC power on the same
cable carrying the preamplier’s output. The antenna should be oriented in the proper direction to maximize reception
of the desired signals (see details below). For best performance, the amplier should be installed near the antenna to
avoid amplifying low level local interference that may enter the coaxial cable leading from the loop antenna to the
preamplier’s input.
Cautions:
• This is a receive-only antenna. Do not connect it to a transmitter as it will be damaged and void your
warranty
• Do not inadvertently connect the 20 VDC output of the power inserter to your receiver’s antenna input as
your receiver may be damaged.
• See attached cautions and warnings relative to lightning protection and antenna installation near high
voltage power lines.
• When operating with nearby transmitting antennas, follow the instructions below to avoid over-driving (or
damaging)yourreceiver’sinputordamagingtheloop’slow-noiseamplier.
Supplied Components (see Figure 16)
QTY Description
1 Loop antenna
1 30 dB preamplier
1 L-bracket
2 Saddle clamps
2 U-bolts
1 lot Mounting Screws and washers
1 Coaxial- Seal package
1 24 VAC wall mount transformer
1 3 ft F-male to F-male jumper cable
1 1 ft F-male to F-male water-proof jumper cable
1 PL-259 Adapter
1 20 VDC power inserter
1 Twin lead to F-female adapter
1 RCA- plug to RCA- plug cable and Y adapter
1 Grounding Lug
2 Nylon shoulder washers (.375 inch)
2 Nylon at washers (.25 inch)
1 Instruction Manual
1
TO
RADIO
TO AMP
OUTPUT (20
VDC)
MODEL P-92A
POWER
INSERTER
PL-259
ADAPTER
RADIO
RECEIVER
24 VAC Wall Mount
Transformer
CAUTION: Do not inadvertently connect 20 VDC
output of Power Inserter to Radio’s antenna input.
The 20 VDC may damage the radio
Figure 1. RF PRO-1B Active Loop Antenna Wiring Diagram
RG-6 Cable
(Not Supplied
)
Input
Output
27 dB
Preamplifier
Model RF30A
Vertical Axis
1 Ft Jumper Cable
115 VAC
Ant
Red
Black
RADIO
RECEIVER
Supplied Twin
Lead Adapter
Alternate Interface for Radios with Twin
Lead Antenna Input
KEY
To KEY output of transceiver (optional)
Page 2
Power Inserter
(see Figures 4 & 15)
2
Figure 1. RF PRO-1B Active Loop Antenna Wiring Diagram
CAUTION: Do not inadvertently connect 20 VDC
output of Power Inserter to Radio’s antenna input.
The 20 VDC may damage the radio.
(sold separately)
3
Positioning the Antenna
This antenna has a directional ‘Figure Eight’ pattern with two deep 25- 30 dB nulls as shown in the diagram in Figure 1,
so for maximum daytime low-angle ground wave reception of a desired signal it should be oriented so that the
imaginary plane in which the loop rests should be vertical to the ground and should, if extended, pass through the
general location of the signal’s transmitter. There is a label on the antenna’s upper junction box that shows the
proper pointing directions for maximum signals and the nulls. At night, for reception of high- angle sky waves
this antenna is less directional and the nulls are far less prominent.
For best results it should be located as far away as possible from any metal objects that could distort or shield the
antenna’s reception like gutters, downpipes, metal plumbing and aluminum foil backed thermal insulation. It can be
positioned indoors or outdoors at least 5 feet above ground level, but for best results it should be as far as possible
from sources of interference such as AC power cables, cat 5 network cables, uorescent lights, light dimmers,
computers and at panel TV’s. If located outdoors it can be camouaged with shrubbery. Ideally a location outdoors
at least 20 feet away from any buildings will yield superior results. It can be mounted to any pole up to 2 inches in
diameter or attached to a at surface or wall via the included L-bracket.
Use with Near-By Transmitting Antennas
The antenna’s low-noise preamplier will withstand RF input levels of at least 30 dBm without failure. In tests with a
1,500 Watt transmit amplier and a ¼ wave vertical transmitting antenna we found that the worst- case loop output
power into the preamp was 10 dBm when the antenna was located 25 ft from a vertical radiator and adjusted for
maximum coupling. This would indicate that at 25 ft separation there is a 20 dB safety margin. The other factor to
consider however is that with this kind of input signal (+10 dBm) the preamplier’s 27 dB gain will cause it to saturate
and output 1.3 watts into the connected receiver. This high saturated output level is a byproduct of the excellent
intermodulation distortion performance of this preamplier, but while most receivers have some sort of input protection
and possibly an internal transmit / receive switch that disconnects or shorts the input when transmitting, we cannot be
sure of what the radio’s protection limits are and we don’t want to be responsible for any damage that may result.
Hence included in the loop’s power inserter is a relay that can be actuated by the “KEY” output of a typical
transceiver. When actuated, the relay disconnects power from the antenna’s preamp. A green LED on the power
inserter is illuminated when power is applied to the preamp. An RCA-plug to RCA-plug cable is included with the
accessories to connect the KEY output of your transceiver to the RCA jack on the side of the power inserter. An RCA
Y-adapter is also included to enable connecting the KEY signal from your transceiver to other equipment. (See
Figures 2 and 3).
The relay’s actuation circuit is designed to operate with a typical transceiver’s 12 VDC “KEY” signal. The power
inserter has internal DIP switches that can be programmed to harmonize relay actuation with the proper state of the
transceiver’s KEY signal. The default setting is such that when the KEY output is “low” (less than 0.7 VDC) the relay
turns on and disconnects the preamp’s power and the connection to your receiver is grounded through a resistor. If
the KEY signal is “high” or greater than 1.2 VDC the relay is not actuated and power is applied to the amplier and
connection is made to your receiver. If the KEY input to the power inserter is left open or disconnected, then power is
always applied to the preamp. If your transceiver has a “KEY” output that goes high on transmit, then you can reverse
the polarity of the power inserter relay actuation by removing the power inserter’s base plate and programming the
DIP switches on the PC board in accordance with the table shown in Figure 4.
A simplied schematic of the relay interface circuit is shown in Figure 5. Note that the KEY input is pulled up internally
via a 10K ohm resistor to the “high” state. If your transceiver’s KEY output is not compatible with this interface circuit
and does not operate the power inserter relay, please contact our customer service (303 526 1965,
[email protected]) for assistance.
To Key Input on Transmitter Amplifier
( if you have one)
To Loop Preamp
Back of Elecraft K3
RF PRO-1B Power Inserter
Figure 2. KEY Wiring For RF PRO-1B Loop Antenna
Typical Transceiver
Page 4
Typical Receiver
Back of Elecraft K3
To Loop Preamp
RF PRO-1B Power Inserter
4
Figure 2. KEY Wiring for RF PRO-1B Loop Antenna
ToKeyInputonTransmitterAmplier
(if you have one)
Transceiver
KEY
Out
RF PRO-1B
POWER INSERTER
KEY
Amplier
KEY
In
Y Adapter
5
Figure 3. KEY Wiring for RF PRO-1B Loop Antenna
KEYINPUT Switch1 Switch2 20VDCANTENNAPOWER
LOW OFF ON OFF
HIGH OFF ON ON
LOW
ON
OFF
ON
Default
Settings
LOW
ON
OFF
ON
HIGH ON OFF OFF
LOW≤0.7VDC
HIGH≥1.2VDC
DIP Switch
DIP
Switch
ON
12
Figure 5. Simplified Relay Interface Schematic
Figure4.PowerInserterDIPSwitchSettings
Figure
5.
Simplified
Relay
Interface
Schematic
To Loop Preamp
(+20 VDC)
Output to Receiver
+20 VDC
10k
10k
+20 VDC+20 VDC
+20 SW 1
SW 2
Key from Transciever
SW 2
Page6
6
Figure 4. Power Inserter DIP Switch Settings
Figure 5.SimpliedRelayInterfaceSchematic
7
Cable
For best results the cable run from the indoor power inserter to the external amplier should be quad shielded RG-6 cable
with male F connectors on each end.
This cable is available with high-quality compression t water-proof F-connectors pre-attached that have internal O-rings
to keep moisture out.
Pixel part numbers:
C-50 50 feet
C-100 100 feet
C-150 150 feet
C-200 200 feet
Standard shield, high quality RG-6 cable can also be used; however the cable’s ability to reject external interference is
reduced by typically 10 dB.
If the cable run from the power inserter to the antenna’s preamplier is longer than 200 feet, then RG-6 cable that has
a solid-core copper center conductor should be used such as Belden 1829AC to minimize DC loss.
WaterproofF–Connectors&WeatherProong
The one foot long RG-6 jumper cable included with the accessories (see Figure 6) is used to connect the output of the
loop to its preamp. This cable uses specially designed F-connectors to eliminate moisture ingress. A package of COAX
seal is supplied for additional weatherproong. Follow the instructions on the side of the package.
Mounting to a Rotator
Figure 7 shows the antenna mounted to a rotator. Many users utilize this conguration to take full advantage of the
antenna’s directional characteristics. Because of the antenna’s low weight and wind loading a very low power rotator
can be used typical of the type used with TV antennas.
MountingtheAmplier
Figures 8 thru 13 show the details for pole mounting the preamplier. Nylon shoulder-washers and nylon at washers are
used to electrically isolate the metal case of the preamplier from the mounting pole. This is required to avoid ground
loops. The preamplier has two small weep holes in its base to drain any condensation that may accumulate internally
and should be orientated in the proper vertical direction as indicated by an arrow on its case. (The preamplier circuit
board is conformal coated to protect it from moisture and corrosion). A 1 foot jumper cable is supplied to connect the
output of the loop antenna to the input of the preamplier. The preamplier’s output should be connected to the 20
VDC output of the power inserter via the lead-in RG-6 cable.
8
Figure 6. One foot RG-6 Jumper cable with water- proof F-connectors.
Connects Loop Antenna Output to Amplifier Input
Page 8
Figure 6. One foot RG-6 Jumper Cable with water-proof F-connectors.
ConnectsLoopAntennaOutputtoAmplierInput.
9
Loop
Antenna
1 foot Jumper
L-Bracket
Preamplifier
Rotor
(Not Supplied)
Service Loop
RG-6 Cable to
Power Inserter
(Not Supplied)
Figure 7. Loop Antenna Mounted on Rotator
Coax-Seal
Page 9
Figure 7. Loop Antenna Mounted on Rotor
10
L-Bracket
1 Foot F-male
to F-male
jumper
27 dB Low Noise
preamplifier
mounted to L -
Bracket
Lightning
Grounding
Lug
Figure 8. Pole Mounting Details
Page 10
B
Figure 8. Pole Mounting Details
Inhaltsverzeichnis
Andere Pixel Antenne Handbücher
Beliebte Antenne Handbücher anderer Marken
Alfa Network
Alfa Network APA-L01 Bedienungsanleitung
Naval
Naval PR-422CA Bedienungsanleitung
Feig Electronic
Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung
TERK Technologies
TERK Technologies TV44 Bedienungsanleitung
Directive Systems & Engineering
Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung
HP
HP J8999A Bedienungsanleitung
CommScope
CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung
Ramsey Electronics
Ramsey Electronics DAP25 Bedienungsanleitung
COBHAM
COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch
Trango Systems
Trango Systems AD900-9 Bedienungsanleitung
Steren
Steren ANT-100 Bedienungsanleitung
Proxim
Proxim 5054-PA-23 Bedienungsanleitung