Planet LN501 Bedienungsanleitung

LoRa Node Controller

LN501

Quick Installation Guide

Table of Contents

1. Package Contents................................................................................. 3

2. Requirements....................................................................................... 4

3. Hardware Installation............................................................................ 5

3.1.1 Remove cover for setting analog input or power output ................ 5

3.1.2 Data Interface........................................................................... 8

3.1.3 Wall Mounting ........................................................................... 9

3.1.4 Pole Mounting ........................................................................ 10

4. Customer Support .............................................................................. 11

1. Package Contents

Thank you for purchasing PLANET Industrial LoRa Node Controller, LN series.

The description of this model is as follows:

LN501 Outdoor IP67 LoRa Node Controller with Solar Panel

“LoRa Node” is used as an alternative name in this Quick Installation Guide.

Open the box of the LoRa Node and carefully unpack it. The box should

contain the following items:

LN501

LoRa Node Controller x 1

Data Cables x 2

Mounting Bracket x 1

Wall Mounting Kits x 1

Hose Clamps x 2

2550 mAh Battery x 2

If any item is found missing or damaged, please contact your local reseller for

replacement.

Caution

1. Never put batteries in mouth. If swallowed, contact your

physician or local poison control center.

2. Do not short circuit; may cause burns or catch fire.

3. Batteries should not be exposed to excessive heat such as

sunshine, fire or the like.

2. Requirements

zWorkstations running Windows 10/11.

zType C USB cable for LN501.

3. Hardware Installation

Refer to the illustration and follow the simple steps below to quickly install

your LoRa Node.

3.1.1 Remove cover for setting analog input or power output

When changing the analog input or power output of LN501 via DIP switch,

follow the steps below:

Step 1: Removethescrewcapsandtakeothebottomcover.

Step 2: Choose or change an analog input and power output via DIP switch.

Type-C USB

LoRa Antenna

Power Button LED Indicator

Analog Input

Power Output

RS485

DIP Switch:

Interface DIP Switch

Power Output

12V (default)

32 1

OFF

32 1

OFF

32 1

OFF

Analog Input

Disable

32 1

OFF

4-20mA ADC

(default)

32 1

OFF

0-10V ADC

32 1

OFF

RS485

Disable

32 1

OFF

Add120ΩresistorbetweenAandB

32 1

OFF

Add1kΩpull-upresistoronA

32 1

OFF

Add1kΩpull-downresistoronB

32 1

OFF

Note

Please turn off the device before changing an analog input or

power output via DIP switch.

Power Button:

Function Action LED Indication

Turn On Press and hold the button for more

than 3s. OOn

TurnO Press and hold the button for more

than 3s. On O

Reset Press and hold the button for more

than 10s. Blinks.

CheckOn/O

Status Quickly press the power button. Light On: Device is on.

LightO:Deviceiso.

Step 3: Put back the bottom cover and tighten the screws.

Note

1. Analog input is set to 4-20mA by default; power output is set

to 12V by default.

2. Power output on interface 1 is used for powering serial port

devices and power output on interface 2 is used for powering

analog devices and SDI-12 devices.

3.1.2 Data Interface

Data Interface 1

Pin Description

5V/9V/12V OUT (Switchable)

12V

(default)

32 1

OFF

32 1

OFF

32 1

OFF

Max.100mA

23.3V OUT, max. 100mA

3GND

4Analog Input 1

5Analog Input 2

65-24V DC IN

Note

When both DC external power and batteries are connected,

external power will be the preferred power supply option.

Data Interface 2

Pin Description

5V/9V/12V OUT (Switchable)

12V

(default)

32 1

OFF

32 1

OFF

32 1

OFF

Max.100mA

23.3V OUT, max. 100mA

3GND

4GPIO1

5GPIO2

6RS232(Tx)/RS485(A)

7RS232(Rx)/RS485(B)

8SDI-12

3.1.3 Wall Mounting

Make sure you have a wall mounting bracket, bracket mounting screws, wall

plugs, wall mounting screws and other required tools.

Step 1: Mark the four holes on the wall you prefer to place the device and

drill the marked four holes for the wall plugs (anchors). Then place

the mounting bracket over the holes with the wall plugs inside, and

tighten it with the screws.

Step 2: Place the device on the mounting bracket and put the small screw

into the hole found on the bottom of the device and then tighten the

screwtonishthejob.

3.1.4 Pole Mounting

Step 1: Straighten out the clamp and slide it through the rectangular rings

in the mounting bracket, and wrap the clamp around the pole. Then

use a screwdriver to tighten the clamp by turning it clockwise.

Step 2: Place the device on the mounting bracket and put the small screw

into the hole found on the bottom of the device and then tighten the

screwtonishthejob.

Note

Please make sure the screws are tightly fixed.

Andere Handbücher für LN501

Inhaltsverzeichnis

Andere Planet Controller Handbücher

Planet

Planet NMS-500 Bedienungsanleitung

Planet

Planet LN501 Bedienungsanleitung

Planet

Planet UNC-NMS Bedienungsanleitung

Planet

Planet LN501 Bedienungsanleitung

Planet

Planet WAPC-500 Bedienungsanleitung

Planet

Planet WAPC-1232HP Bedienungsanleitung

Planet

Planet LN501 Bedienungsanleitung

Planet

Planet NMS-1000V Bedienungsanleitung

Planet

Planet NMS-500 Bedienungsanleitung

Planet

Planet NMS-360 Bedienungsanleitung

Planet

Planet NMC-360V-12 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung