Planet FSD-1605 Bedienungsanleitung

This page is intentionally left blank

Trademarks

Content subjects to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp. All other

trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work properly in

all environments and applications, and makes no warranty and representation,

either implied or expressed, with respect to the quality, performance,

merchantability, or tness for a particular purpose.

PLANET has made every effort to ensure that this User’s Manual is accurate;

PLANET disclaims liability for any inaccuracies or omissions that may have

occurred.

Information in this User’s Manual is subject to change without notice and does

not represent a commitment on the part of PLANET. PLANET assumes no

responsibility for any inaccuracies that may be contained in this User’s Manual.

PLANET makes no commitment to update or keep current the information

in this User’s Manual, and reserves the right to make improvements to this

User’s Manual and/or to the products described in this User’s Manual, at any

time without notice.

If you nd information in this manual that is incorrect, misleading, or

incomplete, we would appreciate your comments and suggestions.

FCC Warning

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the Instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at its own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause

radio interference, in which case the user may be required to take adequate

measures.

WEEE Warning

To avoid the potential effects on the environment and

human health as a result of the presence of hazardous

substances in electrical and electronic equipment,

end users of electrical and electronic equipment

should understand the meaning of the crossed-out

wheeled bin symbol. Do not dispose of WEEE as

unsorted municipal waste and have to collect such

WEEE separately.

Revision

PLANET Fast Ethernet Switch User’s Manual

FOR MODELS: FSD-1605 / FSD-2405

Rev: 1.0(July.2007)

Part No.: EM-FSD1624V1.0 (2081-A31013-000)

1.INTRODUCTION

1.1 Package Contents

Check the contents of your package for following parts:

。 Fast Ethernet Switch x 1

。 User’s manual x 1

。 Power cord x 1

。 Rack ear x 2

。 Rubber feet x 4

If any of these are missing or damaged, please contact your dealer

immediately, if possible, retain the carton including the original packing

material, and use them against to repack the product in case there is a need

to return it to us for repair.

1.2 How to Use This Manual

This Fast Ethernet Switch User Manual is structured as follows:

Chapter 2 Installation

The chapter explains the feature, functionality and the physical installation of

the Fast Ethernet Switch.

Chapter 3 Switch operation

The chapter explains the Fast Ethernet Switch transmit operation.

Chapter 4 Troubleshooting

The chapter explains the troubleshooting of the Fast Ethernet Switch.

Appendix A

This chapter contains cable information of the Fast Ethernet Switch.

In the following section, the term “Fast Ethernet Switch” means the FSD-

1605 and FSD-2405.

1.3 Product Features

。 Complies with IEEE 802.3, 10Base-T, and IEEE 802.3u 100Base-TX

。 16/24-Port 10/100Mbps TX Auto-Negotiation Ethernet Switch

。 Features Store-and-Forward mode with wire-speed filtering and forward-

ing rates

。 IEEE 802.3x flow control for full duplex operation and Backpressure for

half duplex operation

。 Support 8K absolute MAC addresses

。 Supports to handle up to 1552 bytes packet

。 Automatic address learning and address aging

。 Supports Auto MDI/MDI-X function

。 Full/Half-Duplex capability on each TX port

。 LED indicators for simple diagnostics and management

。 Desktop-Si�e and easy installation anywhereDesktop-Size and easy installation anywhere

。 Rack-mountable designRack-mountable design

。 FCC, CE class A compliant

  

Model FSD-1605 FSD-2405



10/100Base-TX Ports 16 RJ-45 MDI/MDI-X 24 RJ-45 MDI/MDI-X

Dimensions (W x H x D) 280 x 170 x 44 mm

Weight (KG) 1.60 KG

Power Consumption 13.6 watts / 46.4BTUwatts / 46.4BTU / 46.4BTUBTU

Power Requirement 100~240 AC, 50-60 H� AC, 50-60 H�AC, 50-60 H�



Switch Architecture Store-and-ForwardForwardorward

Address Table 8K entries, auto learning/ageing

Shared Data Buffer 1.25Mbits

Switch Fabric 3.2 Gbps 4.8 Gbps

Switch Throughput 2.38 Mpps 3.57 Mpps

Flow Control IEEE 802.3x full duplex operating and ow control

Packet Control Runt & CRC ltering

Standard Conformance

Network Standards

IEEE 802.3 (Ethernet)

IEEE 802.3u (Fast Ethernet)

IEEE 802.3x (Flow control)802.3x (Flow control)802.3x (Flow control)

Operation Temperature 0~50ºC

Storage Temperature -20~70ºC

Operation Humidity 10% to 90% (Non-condensing)

Storage Humidity 5% to 90% (Non-condensing)

Regulation Compliance FCC Part 15 Class A, CE

2. INSTALLATION

This section describes the functionalities of the Fast Ethernet Switch’s

components and guides how to install it on the desktop. Basic knowledge

of networking is assumed. Please read this chapter completely before

continuing.

2.1 Product Description

The PLANET Fast Ethernet Switch is 10/100Mbps Fast Ethernet Switch with

16/24 ports respectively, cost-effective; the Fast Ethernet Switch can handle

extremely large amounts of data in a secure topology linking to a backbone or

high capacity servers. The Fast Ethernet Switch has 8K MAC Address table

and provides 1.25Mbit buffer memory. The Fast Ethernet Switch offers wire-

speed packets transfer performance without risk of packet loss. The high

data throughput of the Fast Ethernet Switch makes it ideal for most Fast

environments, especially while network upgrades to a Fast environment.

All RJ-45 copper interfaces support 10/100Mbps Auto-Negotiation for optimal

speed detection through RJ-45 Category 5 or 3 cables. Support is standard

for Auto-MDI/MDI-X that can detect the type of connection to any Ethernet

device without requiring special straight or crossover cables.

The Flow Control function allows your Fast Ethernet Switch supported routers

and servers to directly connect to this Switch for fast, reliable data transfer.

2.1.1 Product Overview

The PLANET Fast Ethernet Switch with 16/24 RJ-45 10/100Mbps ports

for high-speed network connectivity. The Fast Ethernet Switch can also

automatically identify and determine the correct transmission speed and half/

full duplex mode of the attached devices with its 16/24 ports.

The Fast Ethernet Switch also supports Store-and-Forward forwarding

scheme to ensure low latency and high data integrity, eliminates unnecessary

trafc and relieves congestion on critical network paths. With an intelligent

address recognition algorithm, the Fast Ethernet Switch could recognize up

to 8K different MAC address and enables ltering and forwarding at full wire

speed.

2.1.2 Switch Front Panel

Figure 2-1 & 2-2 shows a front panel of Fast Ethernet Switch.

Figure 2-1 FSD-1605 front panel

Figure 2-2 FSD-2405 front panel

2.1.3 LED Indicators

LED Color Function

PWR Green Lights to indicate that the Switch is powered on.

LNK/ACT Green

Lights to indicate the link through that port is

successfully established.

Blinks to indicate that the Switch is actively sendingSwitch is actively sendingwitch is actively sending

or receiving data over that port.

100 Green

Lights to indicate that the port is operating at

100Mbps.

Off to indicate that the port is operating at 10Mbpsto indicate that the port is operating at 10Mbps

2.1.4 Switch Rear Panel

Figure 2-3 shows a rear panel of Fast Ethernet Switch .

Figure 2-3 FSD-1605/2405 rear panel

Power Notice:

1. The device is a power-required device, it means, it will not work till it is

powered. If your networks should active all the time, please consider

using UPS (Uninterrupted Power Supply) for your device. It will prevent

you from network data loss or network downtime.

2. In some area, installing a surge suppression device may also help to

protect your Switch from being damaged by unregulated surge or current

to the Switch or the power adapter.

2.2 Installing the Switch

This part describes how to install your Fast Ethernet Switch and make

connections to it. Please read the following topics and perform the procedures

in the order being presented.

Note: This Fast Ethernet Switch does not need software configuration.

2.2.1 Desktop Installation

To install the Fast Ethernet Switch on desktop, simply follow the next steps:

Step1: Attach the rubber feet to the recessed areas on the bottom of the Fast

Ethernet Switch, as shown in Figure 2-4.

Figure 2-4 Attaching the rubber feet to the Fast Ethernet Switch

Step2: Place the Fast Ethernet Switch on desktop near an AC power

source.

Step3: Keep enough ventilation space between the Fast Ethernet Switch and

the surrounding objects.

Note: When choosing a location, please keep in mind the environmental

restrictions discussed in Chapter 1, Section 1.4 Product Specication.

Step4: Connect your Fast Ethernet Switch to network devices.

A. Connect one end of a standard network cable to the 10/100 RJ-45

ports on the front of the Fast Ethernet Switch.

B. Connect the other end of the cable to the network devices such as

printer servers, workstations or routers…etc.

Note: Connection to the Fast Ethernet Switch requires UTP Category 5

network cabling with RJ-45 tips. For more information, please see the

Cabling Specication in Appendix A.

Step5: Supply power to the Fast Ethernet Switch.

A. Connect one end of the power cable to the Fast Ethernet Switch.

B. Connect the power plug of the power cable to a standard wall outlet.

When the Fast Ethernet Switch receives power, the Power LED should

remain solid Green.

2.2.2 Rack Mounting

To install the Fast Ethernet Switch in a 19-inch standard rack, follow the

instructions described below.

Step1: Place your Fast Ethernet Switch on a hard at surface, with the front

panel positioned towards your front side.

Step2: Attach a rack-mount bracket to each side of the Fast Ethernet Switch

with supplied screws attached to the package. Figure 2-5 shows how

to attach brackets to one side of the Fast Ethernet Switch.

Figure 2-5 Attaching the brackets to the Fast Ethernet Switch.

Caution:

You must use the screws supplied with the mounting brackets. Damage caused

to the parts by using incorrect screws would invalidate your warranty.

Step3: Secure the brackets tightly.

Step4: Follow the same steps to attach the second bracket to the opposite

side.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planet Schalten Handbücher

Planet

Planet IGS-624HPT Bedienungsanleitung

Planet

Planet FGSD-1022 Bedienungsanleitung

Planet

Planet GSD-802S Bedienungsanleitung

Planet

Planet IGS-504HPT Bedienungsanleitung

Planet

Planet WGSD-8020P Bedienungsanleitung

Planet

Planet IGS-6325-20T4C4X Bedienungsanleitung

Planet

Planet GSD-504 Bedienungsanleitung

Planet

Planet IKVM-8000 Bedienungsanleitung

Planet

Planet GSD-802S Bedienungsanleitung

Planet

Planet WGS-803 Bedienungsanleitung

Planet

Planet GS-5220 Series Bedienungsanleitung

Planet

Planet IGS-5225-4T2S Bedienungsanleitung

Planet

Planet IKVM-8010 Bedienungsanleitung

Planet

Planet GS-4210-8P2T2S Bedienungsanleitung

Planet

Planet MII Series Bedienungsanleitung

Planet

Planet FGSW-2620CS Bedienungsanleitung

Planet

Planet IGS-824UPT Bedienungsanleitung

Planet

Planet HPOE-460 Bedienungsanleitung

Planet

Planet IGS-6325-8T4X Bedienungsanleitung

Planet

Planet KVM-1600 Bedienungsanleitung

Planet

Planet WGSD-10020 Bedienungsanleitung

Planet

Planet ISW-504PT Bedienungsanleitung

Planet

Planet WGs-4215-8HP2S Bedienungsanleitung

Planet

Planet ISW-511 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung