Planet WSD-800 Bedienungsanleitung

Managed Ethernet Switches

WSD-800 / WGSD-910 / WGSD-1022C

WSW-2401A / WGSW-2840 / WGSW-5240

Quick Installation Guide

Table of Contents

1. Package Content.......................................................................................... 3

2. Terminal Setup ............................................................................................ 4

3. Logon to the Console ................................................................................... 5

4. Congure IP address.................................................................................... 7

5. Start Web Management................................................................................ 8

1. Package Content

Thank you for purchasing the Planet Layer 2 Managed Switch. In the following

section, the term “Switch” means the Layer 2 Managed Switch.

The PLANET Layer 2 Managed Switch comes with one of the following models.

● WSD-800: 8-Port 10/100Mbps Managed Ethernet Switch

● WGSD-910: 8-Port 10/100Mbps + 1 Gigabit TP/SFP Combo Managed Switch

● WGSD-1022C: 8-Port 10/100Mbps + 2 Gigabit TP/SFP combo Managed Switch

● WSW-2401A: 24-Port 10/100Mbps + 1 Fiber Slot Managed Switch

● WGSW-2840: 24-Port 10/100Mbps + 4G TP/SFP combo Managed Switch

● WGSW-5240: 48-Port 10/100Mbps + 4G TP/SFP Combo Managed Switch

Upon open the box of the Switch and carefully unpack it. The box should contain

the following items:

> The Switch x 1

> This Quick Installation Guide x 1

> User’s manual CD x 1

> Power Cord x 1

> RS-232 Cable x 1

> Rubber feet x 4

> Rack mount accessory x 1

If any item is found missing or damaged, please contact your local reseller

for replacement.

2. Terminal Setup

To congure the system, connect a serial cable to a COM port on a PC or notebook

computer and to serial (console) port of the Switch. The console port of the Switch

is DCE already, so that you can connect the console port directly through PC

without the need of Null Modem.

A terminal program is required to make the software connection to the Switch.

Windows’ Hyper Terminal program may be a good choice. It can be accessed

from the Start menu. Click START, then Programs, Accessories and then Hyper

Terminal.

MS-DOS based terminal program such as PC-PLUS, PROCOMM, can also make the

connection with the Switch. The COM port should be congured as:

□ Baud : 9600

□ Parity : None

□ Data bits : 8

□ Stop bits : 1

□ Flow Control : None

3. Logon to the Console

Once the hardware connection and the terminal program are ready, power on the

Switch. The terminal program will display the testing procedures of the Switch and

show in Figure 3-1.

Figure 3-1 Testing Procedure Screen of the Switch

After boot up is complete, the “switch>” prompt shows up. Enter “enable” for

further conguration. A prompt then shows up for password, please enter “admin”

to enter. As show in Figure 3-2.

Figure 3-2 Login in with Password

The prompt then change to the “switch\enable>”, please enter “?” to list the

commands it offers. As show in Figure 3-3.

Figure 3-3 List commands

Note

1. For security reason, please change and memorize the new pass-

word after this first setup.

2. Only accept password in lowercase letter under console inter-

face.

4. Congure IP address

The default IP address of the Switch is “192.168.0.100”. If you want to change

the IP address, for example, change the IP address to “192.168.99.234” with

subnet mask. “255.255.255.0”, please enter the

command:

set system ip 192.168.99.234 255.255.255.0

As show in Figure 4-1.

Figure 4-1 Set IP address

Now the IP address has changed to 192.168.99.234. The changed IP address will

remain the original after reboot unless you save the conguration. To do this, enter

“copy cong ash” to save the conguration. As show in Figure 4-2.

Figure 4-2 Save conguration

5. Start Web Management

The Switch can be fully managed by console. It also provides a convenient Web

management interface for remote management. This chapter guides the quick

access to the Web Management Interface of the Switch.

Since Web Management Interface can be accessed by Ethernet connection, the

administrator workstation must be in the same IP segment as the Switch.

For example, if you do not change the default IP address of the Switch, say

192.168.0.100, you must set the IP address of your administrator workstation to

be 192.168.0.x (where x is a number between 1 and 254, except 100) with subnet

mask is 255.255.255.0.

Then use the Internet browser (Internet Explorer 5.0 or above), and go to

http://192.168.0.100. Enter the default username “admin” default password

“admin” for login, and the main screen as gure 5-1 appears.

Default IP Address: 192.168.0.100

Default Username and Password: admin

Note

The following screen based on WGSW-2840, for other Layer 2

Management Switch that mentioned in chapter 1, the display will

be the same to WGSW-2840.

Figure 5-1 Web Main Screen of the Switch

You can either manage the Switch through the Web interface or through the

console. Please also refer to the user’s manual in the CD-ROM for more information

about the Switch and the management.

Andere Handbücher für WSD-800

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Planet Schalten Handbücher

Planet

Planet FSD-504HP Bedienungsanleitung

Planet

Planet Switch Bedienungsanleitung

Planet

Planet POE-1200G Bedienungsanleitung

Planet

Planet FSD-803PE Bedienungsanleitung

Planet

Planet KVM-810 Bedienungsanleitung

Planet

Planet GSD-808HP Bedienungsanleitung

Planet

Planet GSD-503 Bedienungsanleitung

Planet

Planet WGSW-2620HP Bedienungsanleitung

Planet

Planet IKVM-8010 Bedienungsanleitung

Planet

Planet WGSW-14020 Bedienungsanleitung

Planet

Planet VC-412 Bedienungsanleitung

Planet

Planet SGSW-24040R Bedienungsanleitung

Planet

Planet GSW-1601 Bedienungsanleitung

Planet

Planet ISW-500 Bedienungsanleitung

Planet

Planet FGSW-1820CS Bedienungsanleitung

Planet

Planet POE-1200G Bedienungsanleitung

Planet

Planet MGS-6320-8HP2X Bedienungsanleitung

Planet

Planet IDL-2402 Bedienungsanleitung

Planet

Planet WGS-6325-8UP2X Bedienungsanleitung

Planet

Planet WSW-2401A Bedienungsanleitung

Planet

Planet WGSW-2403 Bedienungsanleitung

Planet

Planet XGS3-42000R Bedienungsanleitung

Planet

Planet IGS-5225-4T2S Bedienungsanleitung

Planet

Planet GS-5220 Series Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung