Planex Mini-101U Bedienungsanleitung
Mini-101U
10M/100Mbps USB2.0 Print Server
Mini-101U
Foreword
Explanation of the signals
In order to let you set up and use this product correctly, please pay attention when reading or
browsing the manual as you see these signals listed below.
Warning/ Danger
Users should read the explanation carefully and understand it completely, otherwise
users might be in danger or even be injured.
Caution/ Be Careful
Remind users to be careful when setting up the product and to avoid damaging the
product or its system programs.
Seeking for service or searching for an agent or a distributor
Thank you for purchasing products from Planex Communications Inc. If you have any
operational problems while conÀguring or setting up the product, you may contact with our
Customer Service Department or ask the agent or the distributor from which you bought
the product for help. Moreover, during warranty, if you Ànd any defect or breakdown of the
product, you may bring the product, assembly, and its warranty card to our company or to
where you bought the product to ask for repair.
ŘEvery product has different warranty period and contract; please refer to our
company for further information or consult the agent or the distributor.
Planex Communications Inc.
Support PhoneĈ+65-6338-1704 (Singapore)
+886-2-7705-6172/6173/6174 (Taiwan)
Contact Us
TelĈ+886-2-7705-6166
FaxĈ+886-2-7705-6177
Agents & DistributorsĈhttp://www.planex.net/where/index.htm
FCC Certifications
This Equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his/her own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received; including interference that may cause undesired operation.
CE Mark Warning
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2007 All Rights Reserved.
Contents
Foreword
Chapter 1 Introduction to Mini-101U ................1
1. Contents of Package ................
1
2. Specification .......................2
3. Product Functions ...................3
4. How to Set Up Mini-101U3 .............4
Chapter 2 Basic Setup & Configuration ..............5
1. Software Installation & Setup ..........
5
1.1 Administrator Installation ...........7
1.2
How to Use PrintServer Configuration Utility
14
1.2.1 PrintServer Configuration .....14
1.2.2 Network Ports Quick Setup . . . .30
1.2.3 Remote Ports ...............32
1.2.4 Uninstall ...................33
2. Add a New Printer on Windows .......34
2.1 Windows 98.....................34
2.2 Windows ME ....................40
2.3 Windows 2000...................46
2.4 Windows XP ....................53
3. Web Setup and Configuration ........60
3.1 Web Management Interface ......60
3.2 Device Setup→Status.............62
3.2.1 System ....................62
3.2.2 Printer .....................63
Mini-101U Contents
3.2.3 TCP/IP.....................64
3.2.4 SMB.......................65
3.2.5 SNMP .....................66
3.2.6 NetWare...................67
3.2.7 AppleTalk ..................68
3.3 Setup Wizard→Status .............69
3.3.1 System ....................69
3.3.2 Advanced Settings . . . . . . . . . .70
3.3.3 TCP/IP.....................71
3.3.4 SMB.......................73
3.3.5 SNMP .....................74
3.3.6 NetWare...................75
3.3.7 AppleTalk ..................76
3.3.8 Save Settings ...............77
3.4 System Tools→System.............78
3.4.1 Load Default ...............78
3.4.2 Upgrade from Browser .......79
Chapter3 AdvancedSetup&Configuration ......... 81
1. IPP(Interent Printer Protocol) ..........
81
2.
How to Install Network Printer on Apple OS/X
..85
Mini-101U Contents
1
1
Chapter 1 Introduction to Mini-101U
1Introduction to Mini-101U
Thank you for purchasing PCI Mini-101U Print Server. It is a device which
can connect with the Ethernet and reinforce the management over any
printers and brings the performance into full play. Please be aware that
Mini-101U print server does NOT support host-based printers, such as
printers using CAPT, GDI, PPI standards.
Mini-101U Print Server has a 10/100Mbps Ethernet network port and a
USB printer port. Moreover, this print server can comply with multiple
Operating Systems, such as Windows 98/ME/NT/2000/XP/2003, NetWare,
Unix/Linux, and Apple MAC OS9/OS10. It also supports PPTP (Peer-to-
Peer Printing), TCP/IP (LPR), IPP, NetWare Bindery, AppleTalk, SMB
protocols.
With the help of the installation wizard of Mini-101U, you can set up and
configure the settings easily and completely and enjoy the convenience
brought by it instantly. The following chapters will introduce you the
fantastic functions of Mini-101U, the installation methods, and system
configuration in different environments. With all these features, Mini-101U
must be the best solution for both beginners and advanced users.
1. Contents of Package
After purchasing Mini-101U Print Server form a distributor or an agency,
please open the package and check that all the components listed below are
included. If there is any item missing, please contact with the distributor or
the agency at once.
1
2
Mini-101U
œMini-101U Print Server x 1
œCD-ROM (including Driver & Utility, and UserŅsManual)x1
œAC Adapter & Power Cord x 1
œMini-101U Warranty Card x 1
If plug the AC adapter which includes in the product package into
a socket with different voltage power supply, it will cause damage
and that is not included in warranty.
2. SpeciÀcation
Network Management
œWindows Operating System with an installed Ethernet adapter and
support TCP/IP protocol
œInternet browser with Internet Explorer 4.0 or Netscape 4.0 or later.
œA printer with a USB port
œRJ-45 Ethernet cable
Network Management
Mini-101U Print Server support SNMP (Simple Network Management
Protocol), which enables Mini-101U to manage printers and alerts from
remote hosts. Mini-101U has SNMP Agent, so any related applications
supporting SNMP can access and manage it.
Network Configuration
Mini-101U has a built-in Web server, thus it can access its settings through
Web browsers, such as IE, Netscape, Firefox, and so on. It also supports
Server Manager utility program, which uses Windows Interface, so it can
help an administrator to set up and manage every setting easily.
1
3
Chapter 1 Introduction to Mini-101U
3. Product Functions
LED Status Meaning
LAN Blinking /
On
When the power is on, the LAN LED will blink sev-
eral times and then become green all the time. When
transmitting data, the LED will be blinking.
Status On
The Status LED will be on only when printing or
there are some problems with the printer or the print
server.
Ready On After power on Mini-101U, its Ready LED will be
on all the time, and it means you may start to use it.
Button Function Usage
Reset Restart
Press the button for 3-5 seconds, and then unplug the
power cord, but do not release the Reset button and
wait for 3 seconds before plugging the power cord
back. Release the Reset button and Mini-101U will
automatically restart and back to the default settings.
1
4
Mini-101U
4.How to Set Up Mini-101U
1.Unwrap the package of Mini-101U Print Server and check if the
components are complete with nothing missing.
2.Use USB cable to connect Mini-101U Print Server with the printer which
you want to share with others.
3.Plug the RJ-45 cable into the UTP port on Mini-101U Print Server.
4.At last, connect the AC adapter with Mini-101U and plug the other
side of the power cord into the power socket. Power on Mini-101U
Print Server and it will automatically start the POST (Power-On-Self-
Test). While detecting, the Ready LED will be on and LAN LED will
be blinking for a while and then the Mini-101U will be ready in a short
time.
Plug the AC Adapter which comes with Mini-101U in a different
voltage power supply will cause damage on Mini-101U, and it is
not included in warranty.
Inhaltsverzeichnis
Andere Planex Druckserver Handbücher
