Plasmon 8000 Series Bedienungsanleitung
THE PLASMON 8000 SERIES
LF 8602 AUTOLOADER
USER MANUAL
P/N 97663083 A
Storing More Of Your
Digital World ™. Permanently.
New features and changes to information in this document are indicated by change bars. Revision level is
indicated by the letter following the eight-digit document number. If a document has undergone major
modifications, change bars will not be inserted in the document.
Reproduction of this manual, or any portion of this manual, is prohibited without the express permission of
Plasmon Laser Magnetic Storage (LMS). Plasmon LMS reserves the right to make changes in this
document and the product referred to herein without prior notice.
©2000 Plasmon Laser Magnetic Storage
WARNING
Always observe the following when installing, operating or maintaining
this product:
•This unit must be connected to a power distribution system that has a
direct connection to earth ground (Terminated Terra [TT] network/
ground connected). This unit is not suitable for use on a floating
ground (Interrupted Terra [IT]) network.
•The AC input power cord must be shielded and must have a minimum
current rating of 10 A with a nominal cross-section area of 0.75 sq mm
(reference: AWG #18) per conductor, 2 wires plus ground and product
safety approvals as required for use in the country in which the unit is
installed.
•When the unit is mounted in an equipment rack or cabinet, be certain
that the internal temperature within the rack or cabinet does not
exceed the limits defined in the Product Specification or this
document.
•To ensure the integrity of safety features of this unit, maintenance must
be performed only by qualified service personnel using designated
Plasmon LMS parts.
•In case of fire or other emergency, isolate the units from the main
power by disconnecting the power plugs from their site power
receptacles. In situations where disconnecting the plugs is not
possible or practical, use the system main power disconnect to isolate
the units from the main power.
•To prevent fire or shock hazard, do not expose this unit to rain or
moisture. Refer servicing to qualified technicians.
(German Translation)
WARNUNG
•Bei der Installation, Bedienung und Wartung dieses Produkts, bitte
immer die folgenden Vorsichtsmaßnahmen treffen:
•Dieses Gerät mußan ein Stromversorgungssystem angeschlossen
werden, das direkt mit einem Erdungsanschlußverbunden ist
(Terminated- Terra-Netz [TT]/mit Erdanschluß). Dieses Gerät kann
nicht an ein ungeerdetes Netz (Interrupted Terra [IT]) angeschlossen
werden.
•Die Verbindungsschnur des Wechselstromeingangs mußentstört sein
und ihr Minimalstrom unter folgenden Bedingungen bei 10 A liegen:
Der Nennquerschnitt beträgt 0,75 mm je Leiter (Referenz: American
Wire Gauge Nr. 18), es bestehen 2 Drähte plus ein Erdanschlußund
das Produkt entspricht den im Land, in dem es aufgestellt wird,
geltenden Sicherheitsvorschriften.
•Wird das Gerät in ein Gerätegestell oder einen Geräteschrank
eingebaut, ist darauf zu achten, daßdie interne Temperatur im Gestell
oder Schrank nicht über die in den Produktspezifikationen oder
diesem Dokument angegebenen Grenzwerte hinausgeht.
•Um ein ordnungsgemäßes Funktionieren der Sicherheitsmerkmale
dieses Gerätes zu gewährleisten, dürfen Wartungsarbeiten nur von
qualifiziertem Fachpersonal ausgeführt werden. Es sind darüber
hinaus nur Ersatzteile zu verwenden, die von der Firma Plasmon LMS
angegeben werden.
•Im Falle eines Feuers oder in einem anderen Notfall sind die Geräte
vom Hauptnetz zu trennen, indem die Netzstecker aus den
Steckdosen am Einbauort gezogen werden. Ist ein Herausziehen der
Stecker nicht möglich oder zu umständlich, trennen Sie die Geräte mit
Hilfe des System- Hauptnetzabschalters vom Hauptnetz.
•Um Feuer- oder Stromschlaggefahr zu vermeiden, ist dieses Gerät
niemals Regen oder Feuchtigkeit auszusetzen. Wartungsarbeiten
sind qualifiziertem technischen Personal zu überlassen.
Radio/TV Interference (USA)
The information in this section applies only to units in use within the United States:
This equipment generates and uses radio frequency energy and, if not installed and used properly, that is,
in strict accordance with the manufacturer's instruction, may cause interference to radio and television
reception. It has been type tested and found to comply with the limits for a Class A computing device in
accordance with the specifications of Part 15 of FCC Rules, which are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•reorient the receiving antenna
•relocate the equipment away from the receiver
•plug the equipment into a different outlet so that equipment and receiver are on different
branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions. A pamphlet by the FCC How to Identify and Resolve Radio-TV Interference Problems is
available from the US Government Printing Office, Washington, D.C., 20402, Stock No. 044-000-00345-4.
CDRH COMPLIANCE
LF 8602 contains a Class 1 Laser Product. This product complies with 21CFR Chapter 1, Subchapter J,
applicable at date of manufacture.
CANADIAN EMI COMPLIANCE
Canadian Department of Communications standards require that the following statement appear in
operating manuals for any digital apparatus imported into Canada:
This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out in the
Radio Interference Regulations of the Canadian Department of Communications.
FRENCH TRANSLATION
Cet équipement digital ne dépasse pas les limites de la Classe A pour les interférences radioélectriques
des systémes digitaux fixées par les Réglements concernant les Interférences Radioélectriques établis par
le Ministére des Communications du Canada.
All Plasmon LMS products comply with the requirements of this standard.
Agency Compliance and Approval
For details on Agency Compliance and Approval refer to the LF 8602 Product Specification Manual.
TABLE OF CONTENTS
SCOPE 9
RELATED PUBLICATIONS 9
GENERAL DESCRIPTION 11
DRIVE CHARACTERISTICS 13
FRONT PANEL 13
REAR PANEL 13
DIMENSIONS AND WEIGHT 14
TEMPERATURE, HUMIDITY AND ALTITUDE 15
MEDIA ENVIRONMENTAL CHARACTERISTICS 16
SHOCK AND VIBRATION 16
AC POWER REQUIREMENTS 17
AC GROUND 17
AC POWER CORD 17
TILT RANGE 18
HEAT DISSIPATION 18
PARTICULATE LIMITS 18
WARNING LABELS 18
UNPACKING AND REPACKING INSTRUCTIONS 19
UNPACKING THE LF 8602 19
INSPECTING THE LF 8602 25
REPACKING THE LF 8602 25
INSTALLATION 31
INSTALLATION REQUIREMENTS 31
SCSI BUS CONSIDERATIONS 32
CONNECTING POWER AND SCSI CABLING 35
SINGLE-DEVICE CONFIGURATION 36
MULTIPLE-DEVICE CONFIGURATION 37
CONNECTOR VERIFICATION 37
EXTENSION PROCEDURES 38
OPERATING INSTRUCTIONS 41
CONTROLS AND INDICATORS 41
POWER-ON PROCEDURE 42
MODES OF OPERATION 43
OPERATING MODE 43
CONFIGURATION MODE 45
VIEWING THE CONFIGURATION ("VIEW CONFIG") 48
SETTING THE CONFIGURATION MENU OPTIONS 49
SET DEFAULTS 53
SETTING THE SCSI ID 53
SETTING THE BUS PARITY CHECKING 54
SETTING THE LANGUAGE 54
SETTING THE WRITE PROTECT OPTION 55
SETTING THE MEDIA AUTOLOAD OPTION 55
SETTING THE LOAD SWITCH OPTION 56
SETTING THE READ AHEAD OPTION 56
SETTING THE CDE CURS OPTION 57
SETTING THE BUSY OPTION 58
SETTING THE MODSEL RA OPTION 58
SETTING THE MM SPINUP OPTION 59
SELECT TARGET NEGOTIATION 59
THE DIAGNOSTIC MENU 60
SET THE INTERNAL DRIVE SERIAL NUMBER ("SET SERIAL #") 65
TEST MODE 67
MEDIA CARTRIDGE HANDLING 68
SETTING THE WRITE PROTECTION SWITCH 70
AFFIXING LABELS 71
MEDIA INSERTION AND REMOVAL 71
MEDIA ACCESS DOOR 71
CARTRIDGE INSERTION 73
CARTRIDGE REMOVAL 74
MANUAL CARTRIDGE RELEASE MECHANISM 75
OPENING THE BASEPLATES 75
REMOVING THE BEZEL 76
RETRACTING THE CARTRIDGE 78
MEDIA LOADING 79
OPERATOR MAINTENANCE 81
ACCESSING DRIVES 81
INSPECTING AND CLEANING FAN AND BLOWER FILTERS 83
REPLACING FUSES 84
MEDIA CLEANING 85
MEDIA CLEANING USING CLEANING KIT P/N 97662550 85
APPENDIX A 87
GERMAN TRANSLATIONS/ÜBERSETZUNGEN INS DEUTSCHE 87
97663083 A
Page 9
SCOPE
This User Manual describes unpacking, installing, operating, and maintaining the Plasmon LF 8602
Autoloader High-Performance Optical Disk Drive.
RELATED PUBLICATIONS
WARRANTY STATEMENT
The LF 8602 is warranted as stated in the purchase agreement between Plasmon and its customer,
or the Plasmon sales order acknowledgment, whichever is applicable.
The Plasmon LMS quality system is in compliance and registered to ISO 9001. The LF 8602 is
manufactured from new parts, or remanufactured parts.
LF 8602 warranty does not cover defects or damage caused by the use of unauthorized parts or
repairs or improper use or maintenance. Repairs or replacements not covered by the warranty will
be invoiced at LMS’ then current prices.
The warranty is void when installation, service or repairs are performed by unauthorized
personnel; when the product is affected by unauthorized alterations, modifications or other
tampering or misuse; when the product is incorporated into a system which causes or involves
any changes in the physical, mechanical or electrical arrangement of the product; or when the
product is not used in accordance with its applicable specifications.
The term, authorized personnel, is defined as those persons who have been trained by Plasmon
LMS Technical Services.
Publication Part Number
LD 8100/LF 8120/LF 8600/LF 8602 Product Specification 97663035
LD 8100/LF 8120/LF 8600/LF 8602 SCSI Interface Specification 97662164
LF 8120/LF 8600/LF 8602 Hardware Maintenance Manual 97663082
PLASMON L M S - LF 8602 USER MANUAL
Page 10
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Plasmon CD/CDR-Laufwerk Handbücher
Beliebte CD/CDR-Laufwerk Handbücher anderer Marken
SmartDisk
SmartDisk Firewire CD-R/W Bedienungsanleitung
Axis
Axis CD-ROM SERVER Bedienungsanleitung
LG
LG CRD-8322B Bedienungsanleitung
Memorex
Memorex 32023234 - 52x32x52x External USB2.0 CD... Montageanleitung
Yamaha
Yamaha CD Recordable/Rewritable Drive CRW3200 Bedienungsanleitung
Sony
Sony CRX230AE Bedienungsanleitung
