Pleasant hearth VFF-PH20D Bedienungsanleitung

VENT-FREE GAS

DUAL FUEL FIREPLACE

MODEL #VFF-PH20D

VFF-PH26D

VFF-PH32DR

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

CAUTION - FOR YOUR SAFETY

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-447-4768, 8:30 a.m. – 4:30 p.m., CST, Monday – Friday or

email us at [email protected].

WARNING: This appliance

is equipped for (Natural and

Propane) gas. Field conversion

is not permitted other than

between natural or propane

gases.

- Do not store or use gasoline or other ammable vapors and Iiquids in vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the re department.

- Installation and service must be performed by a qualied installer, service agency or the

gas supplier.

This is an unvented gas-red heater. It uses air (oxygen) from the room in which it is

installed. Provisions for adequate combustion and ventilation air most be provided.

Refer to Air For Combustion and Ventilation section on page 8 of this manual.

This appliance may be installed in an aftermarket, permanently located manufactured (mobile)

home, where not prohibited by local codes. This appliance is only for use with propane or

natural gas. This appliance is equipped with a simple means to switch between propane and

natural gas. Field conversion by any other means including the use of a kit is not permitted.

NG LP

Dual Fuel

418-S-06-5

ANSI Z21.11.2-2011

Rev. 2013-05-10

WARNING: Read the Installation & Operating Instructions before using this appliance.

IMPORTANT: Read all instructions and warnings carefully before starting installation.

Failure to follow these instructions may result in possible injury to persons or a re

hazard and will void the warranty.

TABLE OF CONTENTS

Specications ................................................................................................................................... 2

Important Safety Information ............................................................................................................3

Product Identication........................................................................................................................ 5

Product Features.............................................................................................................................. 6

Unpacking......................................................................................................................................... 6

Hood Assembly................................................................................................................................. 7

Preparing for Installation................................................................................................................... 8

Installation ...................................................................................................................................... 11

Operation........................................................................................................................................ 23

Care and Maintenance ................................................................................................................... 26

Troubleshooting.............................................................................................................................. 29

Replacement Parts......................................................................................................................... 31

Accessories .................................................................................................................................... 32

Warranty ......................................................................................................................................... 34

Model VFF-PH20D VFF-PH26D VFF-PH32DR

Input Rating 20,000 BTU/Hr 27,500 BTU/Hr 32,000 BTU/Hr

Gas Type

Manifold Pressure

Max. Inlet Pressure

Min. Inlet Pressure

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• replace will not produce specied heat

• for propane/LP units, propane/LP gas supply may be low

You may feel your gas pressure is too low. If so, contact your local natural or propane/LP gas supplier.

10'' WC

13'' WC

8'' WC

4.5'' WC

10'' WC

3.5'' WC

10'' WC

13'' WC

8'' WC

4.5'' WC

10'' WC

3.5'' WC

10'' WC

13'' WC

8'' WC

4.5'' WC

10'' WC

3.5'' WC

IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate,

or service this heater. Improper use of this heater can cause serious injury or death from burns, re,

explosion, electrical shock, and carbon monoxide poisoning.

IMPORTANT SAFETY INFORMATION

Only a qualied installer, service agent, or local gas supplier may install and service this product.

WARNING: Do not store or use gasoline or other ammable vapors or liquids in the vicinity

of this or any other appliance.

WARNING: This appliance can be used with propane or natural gas. It is shipped from the

factory adjusted for use with propane.

CARBON MONOXIDE POISONING: Early signs of carbon monoxide poisoning resemble the u

with headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly.

Get fresh air immediately! Have heater serviced. Some people are more affected by carbon monoxide

than others. These include pregnant women, people with heart or lung disease, people who are

anemic, those under the inuence of alcohol, and those living in high altitudes.

NATURAL AND PROPANE/LP GAS: Natural and Propane/LP gases are odorless. An odor-making

agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the

gas can fade. Gas may be present even though no odor exists. Make certain you read and under-

stand all warnings. Keep this manual for reference. It is your guide to operating this heater safely.

WARNING: Any change to this replace/heater or its controls can be dangerous.

WARNING: Do not use any accessories not approved for use with this heater.

WARNING: Carefully supervise young children when they are in the room with the heater.

WARNING: Heater becomes very hot when operating. Keep children and adults away from hot

surfaces to avoid burns or clothing ignition. Heater will remain hot for a time after shutoff. Allow

surfaces to cool before touching.

WARNING: Keep the appliance area clear and free from combustible materials, gasoline, and

other ammable vapors and liquids.

WARNING: Due to high temperatures, locate this appliance out of trafc and away from

furniture and draperies.

WARNING: Do not place clothing or other ammable material on or near the appliance. Never

place any objects in the heater.

CALIFORNIA PROPOSITION 65

Fuels used in gas or oil red appliances and the products of combustion of such fuels contain

chemicals known to the state of California to cause cancer, birth defects or other reproductive

harm. This product contains chemicals, including lead and lead compounds, known to the state of

California to cause cancer, birth defects or other reproductive harm. Wash hands after handling.

SAFETY INFORMATION

1. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is

not convertible for use with other gases.

Do not place propane/LP supply tank(s) inside any structure. Locate propane/LP supply tank(s) outdoors.

3. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in your building

• immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions

• if you cannot reach your gas supplier, call the re department

4. This replace shall not be installed in a bedroom or bathroom.

5. Do not use this replace as a wood-burning replace. Use only the logs provided with the replace.

6. Do not add extra logs or ornaments such as pine cones, vermiculite or rock wool. Using these

added items can cause sooting. Do not add lava rock around base. Rock and debris could fall into

the control area of replace.

7. This replace is designed to be smokeless. If logs ever appear to smoke, turn off replace and

call a qualied service person. Note: During initial operation, slight smoking could occur due to log

curing and replace burning manufacturing residues.

8. To prevent the creation of soot, follow the instructions in Cleaning and Maintenance, page 26.

9. Before using furniture polish, wax, carpet cleaner or similar products, turn replace off. If heated,

the vapors from these products may create a white powder residue within burner box or on adjacent

walls or furniture.

10. This replace needs fresh air ventilation to run properly. This replace has an Oxygen Depletion

Sensing (ODS) safety shutoff system. The ODS shuts down the replace if not enough fresh air is

available. See Air for Combustion and Ventilation, page 9. If replace keeps shutting off, see

Troubleshooting, page 28.

11. Do not run replace

• where ammable liquids or vapors are used or stored.

• under dusty conditions.

12. Do not use this replace to cook food or burn paper or other objects.

13. Never place any objects in the replace or on logs.

14. Do not use replace if any part has been under water. Immediately call a qualied service technician

to inspect the room replace and to replace any part of the control system and any gas control which

has been under water.

15. Turn off and unplug replace and let cool before servicing. Only a qualied service person

should service and repair replace.

16. Operating replace above elevations of 4,500 feet could cause pilot outage.

17.

Do not operate replace if log is broken. Do not operate replace if log is chipped (dime-sized or larger).

18. To prevent performance problems, do not use propane/LP fuel tank of less than 100 lb. capacity.

19. Provide adequate clearances around air openings.

Screen

Log

Ignitor Button

Hood

Fireplace

Cabinet

Control Knob

PRODUCT IDENTIFICATION

Screen

Log

Ignitor Button

Hood

Fireplace

Cabinet

Control Knob EI Receiver

Remote

Transmitter

Mantel

Cabinet

WARNING: This replace is designed for use with the mantel cabinet provided. Installing

the replace cabinet without the provided mantel or substituting another mantel will void the

warranty and could resuly in property damage and personal injury.

Fig. 1 - Vent-Free Dual Fuel Fireplace

VFF-PH32DRVFF-PH26D/VFF-PH20D

UNPACKING

1. Remove replace cabinet and hood from carton. Log is wrapped and inside replace.

Do not remove at this time.

2. Remove all protective packaging applied to replace for shipment.

3. Make sure your replace includes one hardware packet.

4. Check replace for any shipping damage. If replace is damaged, call GHP Group, Inc., at 1-877-

447-4768. Please do not return it to the store.

SAFETY PILOT

This heater has a pilot with an Oxygen Depletion Sensing (ODS) safety shutoff system.

The ODS/pilot shuts off the heater if there is not enough fresh air and cuts off main burner gas in the

event of ame out.

ELECTRIC PUSH BUTTON IGNITION SYSTEM

This heater is equipped with an electronic piezo control system. This system requires

one AAA battery batteries (provided).

THERMOSTAT HEAT CONTROL

The control automatically cycles the burner on and off to maintain a desired room

temperature. See page 24.

DUAL FUEL CAPABILITY

Your heater is equipped to operate on either propane or natural gas. The heater is

shipped from the factory ready for connecting to propane. The heater can easily be

changed to natural gas by having your qualied installer follow the instructions on page

18 and the markings on the heater.

BLOWER KIT (OPTIONAL)

The blower kit helps to distribute the warmed air into the space more rapidly.

State of Massachusetts: The installation must be made by a licensed plumber or gas tter in

the Commonwealth of Massachusetts. Sellers of unvented propane or natural gas-red

supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale

of the unit.

In the State of Massachusetts, unvented propane or natural gas-red space heaters shall

be prohibited in bedrooms and bathrooms.

In the State of Massachusetts the gas cock must be a T-handle type. The State of

Massachusetts requires that a exible appliance connector cannot exceed three feet

in length.

LOCAL CODES

Install and use heater with care. Follow all codes. In the absence of local codes, use the latest edi-

tion of The National Fuel Gas Code, ANSI Z223.1, also known as NFPA 54*.

*Available from:

American National Standard Institute, Inc. National Fire Protection Association, Inc.

1430 Broadway 1 Batterymarch Park

New York, NY 10018 Quincy, MA 02269-9101

This heater is designed for vent-free operation. State and local codes in some areas prohibit the use

of vent-free heaters.

PRODUCT FEATURES

HOOD ASSEMBLY (IF REQUIRED)

WARNING: Always have screen in place before operating replace. This prevents

excessive temperatures on replace surfaces.

WARNING: Failure to position the parts in accordance with these diagrams or failure to

use only parts specically approved with this replace may result in property damage

or personal injury.

Tools Required:

• Phillips screwdriver • scissors

1. If equipped, lift replace screen up

and pull out to remove (See. Fig 2). Set

screen aside until installation has been

completed.

2. Cut two plastic straps to remove log

from rebox cavity. Set log aside.

3. An optional blower is available. See

Accessories, page 36. Install optional

blower now. Follow installation

instructions provided with blower.

4. Locate four black Phillips sheet metal

screws in hardware packet.

5. Slide hood between louver and

rebox top and align screw holes.

6. Insert screws as shown in Figure 3.

Tighten screws rmly. Fig. 2 - Removing and Installing Screen

Fig. 3 - Assembling Hood

(If Required)

Shoulder Screw

Screen

Firebox Top

Louver

Sheet Metal

Screws

Hood

PREPARING FOR INSTALLATION

AIR FOR COMBUSTION AND VENTILATION

WARNING: This heater shall not be installed in a room or space unless the required volume

of indoor combustion air is provided by the method described in the Nation Fuel Gas Code, ANSI

Z223.1/NFPA 54, the International Fuel Gas Code, or applicable local codes.

PRODUCING ADEQUATE VENTILATION

All spaces in homes fall into one of the three following ventilation classications:

1. Unusually Tight Construction

2. Unconned Space

3. Conned Space

The information on pages 9 through 11 will help you classify your space and provide adequate ventilation.

Conned and Unconned Space

A conned space as a space whose volume is less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3 per kw)

of the aggregate input rating of all appliances installed in that space and an unconning space as a

space whose volume is not less than 50 cu. ft. per 1,000 BTU/hr (4.8 m^3 per kw) of the aggregate

input rating of all appliances installed in that space. Rooms connecting directly with the space in

which the appliances are installed*, through openings not furnished with doors, are considered a

part of the unconned space.

This heater shall not be installed in a conned space or unusually tight construction unless provisions

are provided for adequate combustion and ventilation air.

* Adjoining rooms are connecting only if there are doorless passageways or ventilation

grills between them.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and venti-

lation. However, in buildings of unusually tight construction, you must provide additional

fresh air.

Unusually tight construction is dened as construction where:

a) walls and ceilings exposed to the outside atmosphere have a continuous water vapor retarder

with a rating of one perm (6x10-11kg per pa-sec-m2) or less with openings gasketed or sealed

and

b) weather stripping has been added on windows that can be opened and on doors and

c) caulking or sealants are applied to areas such as joints around window and door frames,

between sole plates and oors, between wall-ceiling joints, between wall panels, at

penetrations for plumbing, electrical, and gas lines, and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air.

See “Ventilation Air From Outdoors” (page 9). If your home does not meet all of the

three criteria above, proceed to “Determining Fresh-Air Flow For Heater Location”.

PREPARING FOR INSTALLATION

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Conned or Unconned Space

Use this worksheet to determine if you have a conned or unconned space.

Space: Includes the room in which you will install heater plus any adjoining rooms with

doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space Length × Width × Height = cu. ft. (volume of space)

Example: Space size 20 ft. (length) × 16 ft.(width) × 8 ft. (ceiling height) = 2560 cu. ft. (volume

of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these

rooms to the total volume of the space.

2. Divide the space volume by 50 cu. ft. to determine the maximum BTU/hr the space can support.

_______ (volume of space) ÷ 50 cu. ft.= (Maximum BTU/hr the space can support)

Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum BTU/hr the space

can support)

3. Add the BTU/hr of all fuel burning appliances in the space.

Vent-free heater _________ BTU/hr

Gas water heater* ________BTU/hr

Gas furnace _____________BTU/hr

Vented gas heater ________BTU/hr Example:

Gas heater logs __________BTU/hr Gas water heater 30,000 BTU/hr

Other gas appliances*+ ____BTU/hr Vent-free heater + 26,000 BTU/hr

Total = ____BTU/hr Total = 56,000 BTU/hr

*Do not include direct-vent gas appliances. Direct-vent draws combustion air from the

outdoors and vents to the outdoors.

4. Compare the maximum BTU/hr the space can support with the actual amount of BTU/hr used.

_______ BTU/hr (maximum the space can support)

_______ BTU/hr (actual amount of BTU/hr used).

Example : 51,200 BTU/hr (maximum the space can support) 56,000 BTU/hr (actual amount of

BTU/hr used)

The space in the above example is a conned space because the actual BTU/hr used is more than

the maximum BTU/hr the space can support.

You must provide additional fresh air. Your options are as follows:

a) Rework worksheet, adding the space of an adjoining room. If the extra space provides an

unconned space, remove door to adjoining room or add ventilation grills between rooms. See

“Ventilation Air From Inside Building,” page 11.

b) Vent room directly to the outdoors. See “Ventilation Air From Outdoors”, page 11.

c) Install a lower BTU/hr heater if lower BTU/hr size makes room unconned. If the actual BTU/hr

used is less than the maximum BTU/hr the space can support, the space is an unconned space.

You will need no additional fresh air ventilation.

Andere Handbücher für VFF-PH20D

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere pleasant hearth Kamin im Innenbereich Handbücher

pleasant hearth

pleasant hearth GLF-5002-50 Bedienungsanleitung

pleasant hearth

pleasant hearth VFL-CO18DT Bedienungsanleitung

pleasant hearth

pleasant hearth VFF-PH20D Bedienungsanleitung

pleasant hearth

pleasant hearth 23-700-712 Bedienungsanleitung

pleasant hearth

pleasant hearth 28-54-70 Bedienungsanleitung

pleasant hearth

pleasant hearth 24-900-001 Montageanleitung

pleasant hearth

pleasant hearth 23-68-48M Bedienungsanleitung

pleasant hearth

pleasant hearth HENSLEY 230-752-242 Bedienungsanleitung

pleasant hearth

pleasant hearth VFL2-VO24DR Bedienungsanleitung

pleasant hearth

pleasant hearth PH26D Bedienungsanleitung

pleasant hearth

pleasant hearth GLF-5002-75 Bedienungsanleitung

pleasant hearth

pleasant hearth VFL2-VO24DR Bedienungsanleitung

pleasant hearth

pleasant hearth 248-12-68M Bedienungsanleitung

pleasant hearth

pleasant hearth VL-WO18D Bedienungsanleitung

pleasant hearth

pleasant hearth 366-843-241 Bedienungsanleitung

pleasant hearth

pleasant hearth 18-600-310 Montageanleitung

pleasant hearth

pleasant hearth 23-412-17 Bedienungsanleitung

pleasant hearth

pleasant hearth 23-700-712 Installationsanleitung

pleasant hearth

pleasant hearth VFF-PH20D Bedienungsanleitung

pleasant hearth

pleasant hearth CHERRY FINISH Bedienungsanleitung

pleasant hearth

pleasant hearth VFL2-RW18DT Bedienungsanleitung

pleasant hearth

pleasant hearth 321-42-10 Bedienungsanleitung

pleasant hearth

pleasant hearth PHZC32C Bedienungsanleitung

pleasant hearth

pleasant hearth 23-29-65 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung