plottiX iXpress Classic 2 Bedienungsanleitung
English 2-11
Deutsch 12-23
2
Safety Instructions ............................................................................................................................. 2-3
In the Box & Overview ............................................................................................................................ 4
Funktion Keys ........................................................................................................................................ 5
Operating Instructions....................................................................................................................... 6-9
FAQ ................................................................................................................................................. 10-11
Safety Instructions
Please read this manual carefully before
using the device for the rst time. Remove all
packaging before using the device. The device
is intended for household use. If it is used in an
inappropriate manner or in a manner dierent
from that described in this manual, the manu-
facturer assumes no liability and the warranty is
void.
Do not pull on the power cord of the appliance
to unplug the device. Always unplug the device
from the power outlet when not in use.
The device must be used on a at, stable and
heat-resistant surface. Make sure that the heat-
resistant tray of the transfer press is also on a
stable, at and heat-resistant surface.
The device is not suitable for persons whose
physical or mental integrity or their perceptive
abilities are limited, or for persons with insui-
cient knowledge and experience.
This product is not suitable for children. Make
sure that the device is not suitable for playing.
Make sure that the device and the power plug
are out of reach for children under the age of 8
years.
Do not leave the device unattended while it is
connected to the power supply or has not cooled
down (approx. 1 hour aer use).
Do not use the device if it shows visible dama-
ge, has been dropped or does not operate as
intended.
Check the power plug and power cord for any
damage or attrition before using the device. Roll
o the power cord completely before plugging
the machine into the power outlet. The power
cord should not get in contact with sharp edges
or heat sources. Also prevent contact between
cable and pressing surface of the device. If the
power plug or power cord is damaged, it must be
repaired before use.
Index & Safety Instructions
3
Do not open the device or other components
(including the power plug and cable). Repairs
may only be carried out by authorized work-
shops.
Never immerse the device in water or other
liquids.
The pressing surface of the device can reach
very high temperatures: Do not touch it!
Let the device cool down completely before
storing it (approx. 1 hour aer use).
Please keep the user manual for future refe-
rence!
Tip: Keep the original carton. The transfer press
is optimally protected in there and allows a safe
transport in case of warranty.
This device contains raw materials that can
be recycled. Please dispose of this device in an
environmentally friendly manner at a collection
point in your town or municipality.
Safety Instructions
General
Danger
Symbol
Danger
from hot
Surfaces
Danger of
bruises
Plug out
the power
cable
WEEE-
Reg.No.
DE72497967
4
Product size: 249 x 249 x 108mm (LxWxH)
Heating plate size: 228 x 228 mm
1 x plottiX iXpress Classic 2
1 x Heat resistant tray
1 x User manual
iXpress Classic 2 Function Keys
For switching on and o and
for setting the temperature and time.
Digital Display
For the display of
temperature and time.
Non-stick press surface
Provides dry and even heat for
error-free transfers. With non-stick
coating for additional smoothness
and durability.
Heat resistant tray
Storage space for the iXpress Classic 2
heat press when you are not using it or
when the machine is heating up.
In the Box & Overview
Product power: 1000W
Product voltage: 220V-230V
iXpress Classic 2 Comfort Handle
Provides comfortable and stable grip
during use.
5
Function Keys
On/O Power Button
For switching the iXpress Classic 2 transfer press on and o.
TEMP Button
1. Press the TEMP Button to enter the temperature setting mode. The temperature
display starts to ash.
2. Press the keys to select the desired temperature for your transfer. You
can set a value between 100°C and 205°C, in increments of 5.
3. Press the TEMP Button again to save the current setting. Alternatively, the press
will save the setting aer 5 seconds of no input.
Tip: Press and hold the TEMP Button if you wish to switch the temperature scale
from Fahrenheit to Celsius
TIMER Button
1. Press the TIMER Button to enter the Countdown setting mode. The time display
will start ashing.
2. Press the keys to set the desired countdown for your transfer. You can set
a value between 1 and 600 seconds.
3. Press the TIMER Button again to save the setting. Alternatively, the press will save
the settings aer 5 seconds without input.
START Button
1. Press the START Button to start the countdown. The countdown is shown in the
display.
2. As soon as the countdown is over, a beep sounds three times.
6
Operating Instructions
Celsius
Fahrenheit
Seconds
Time display
Heat indicator
Digital Display
1Place the press on the heat resistant tray.
2Insert the power plug into the socket.
Make sure that the mains voltage of the socket corresponds to the
specied mains voltage of the iXpress Classic 2.
Note:
Unplug the device from the power outlet when not in use.
7
Operating Instructions
3Press the On/O Power Button to turn the press on. The press
starts to warm up.
4Set your desired temperatur and time with the correspond
buttons and arrow buttons as explained on page 5.
Warning:
Please note that the transfer press heats up accordingly to set
temperature. Risk of burns by touching.
5Aer setting temperature and time the transfer press starts pre-
heating. Please wait until the temperature display has reached the
set temperature.
As soon as the press has reached the desired temperature, a signal
tone sounds and the START Button lights up green.
8
Operating Instructions
6During preheating, you can already place your material on a sui-
table base, for example on a silicone mat for transfer presses, and
position your design to be transferred on the material.
Tip: If you want to press a textile, then pre-iron it for 3-5 seconds
to remove any wrinkles and moisture.
7Place the press on the design to be transferred and start the
countdown with the START Button.
8Apply pressure until the countdown ends. Once the countdown is
over, the beep sounds three times and the transfer is complete.
Warning:
Pay attention that there should be no other materials as the
design and the medium to press is between the press and the
surface. Risk of bruises if done otherwise.
9
Operating Instructions
Need help?
You can nd temperatures and pressing times for all the plottiX
iron-on foils on:
www.plottix.de/en/help/
9Place the iXpress Classic 2 back on the heat resistant tray. Press
the On/O Power Button to switch o the press.
Caution: If you are not using the iXpress Classic 2 for more than 10
minutes, it switches o automatically.
Note:
Unplug the device from the power outlet when not in use.
10
FAQ
Q: What are the tips for successful transfers with iXpress Classic 2 transfer
press?
A: Three things are important for perfect transfers that last:
1. A rm, even surface. Kitchen islands, countertops, or sturdy tables work well. Ironing boards and
plastic tables are not sturdy enough for successful transfers. We also suggest the use of our silicone
mat.
2. Use the recommended settings for the iron-on and base material you‘re using.
3. Make sure you apply rm pressure during transfer.
Q: I followed the instructions, and my iron-on didn’t stick. What happened?
How do I get it to work?
A: There are several reasons why a transfer does not work properly:
1. The press did not make full contact with the base material. This could be because of seams, zippers,
or anything else that will cause you to not have an even surface.
2. Verify that your machine is set to the recommended settings.
3. Make sure that you choose the recommended pressing time. If the settings are correct press the
front and back of material with heat for an additional 10-15 seconds.
Q: The temperature of the heat press drops when I use it. Is something wrong with my press?
A: The press temperature may uctuate briey aer heating when it is placed on the base material.
This is due to the temperature dierence between the heated plate and the base material. Do not
worry, the heat press will quickly return to the selected setting.
Q: My device keeps turning o and I have to turn it back on. Why?
A: This is the auto shut-o safety feature of iXpress Classic 2 transfer press. Aer 10 minutes of inacti-
vity, the press will automatically turn o.
Inhaltsverzeichnis
Sprachen:
