Plura PIPM-R-7-Type C Bedienungsanleitung
Re-imagine Beyond Technology sales@plurainc.com
Operating Instructions
PIPM-R-7-Type C
"Plura IP Module" for SFP-H-7 Series
SFP-317-H-7
SFP-321-H-7
SFP-324-H-7
SFP-332-H-7
SFP-347-H-7
SFP-355-H-7
SFP-324-H-7
SFP-Modules
Operating Instructions
SFP-H-7 SERIES with PIPM-R-7-TypeC
Re-imagine Beyond Technology sales@plurainc.com
REVISION HISTORY
VERSION DATE CHANGES
1.00 2022-01-06 1st official release
6
6
7
7
9
10
10
10
12
12
12
14
16
17
19
19
19
21
21
21
22
1. OVERVIEW
2. GENERAL FEATURES
3. PRODUCTION WORKFLOW AND I/O CONNECTIONS
1) PRODUCTION WORKFLOW
2) I/O & CONNECTIVITY
4. INSTALLATION OVERVIEW
1) INITIAL SETUP BY WEB BROWSER
2) CONNECTING TO THE CONTROL LAN USER INTERFACE “UI”
5. WEB CONFIGURATION & INTERFACE
1) OVERVIEW
2) EMBER+ CONTROL UPDATE
3) MONITOR FPGA AND FIRMWARE
4) EMBER+/TSL LICENSE UPDATE
5) WEB UI UPDATE
6. MEDIA LAN 2110 CONTROL (OUT-BAND)
1) OVERVIEW
2) MANAGEMENT VIA CONTROL LAN UI
3) 10G/25G SWITCH CONFIGURATION REQUIREMENTS
4) 2022-7 HITLESS SWITCHING TOGGLE ON - CONFIGURING FLOWS FOR
REDUNDANCY
5) 2022-7 HITLESS SWITCHING TOGGLE OFF - CLEAN SWITCH MODE
6) IMPORTING SDP FILES
7) SPECIFIC CONFIGURING USING REST URLS VIA REST API CLIENT 24
Operating Instructions2
SFP-H-7 SERIES with PIPM-R-7-TypeC
2
Re-imagine Beyond Technology sales@plurainc.com
•PRECAUTION
Before operating this unit, please read this manual carefully.
WARNING:
To reduce the risk of any electric shock, please do not remove the back cover. No user serviceable parts inside. Refer any service matters to
qualified service personnel. To prevent fire or shock hazard, do not expose the rear of the set to rain or moisture. Do not rub, clean or hit the
Active Matrix LCD with object that may scratch, mark, or damage the Active Matrix LCD permanently.
CAUTION:
Unauthorized tampering with the inside of the monitor invalidates the warranty.
The manufacturer shall not warrant for any damage caused by improper maintenance and/or repair or work by third parties.
Important safeguards for you and your new product:
Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or
fire hazards. Please read and observe the following safety points when installing and using your new product and save them for future
reference.
1. Read Instructions
2. Follow Instructions
All operating and use instructions should be followed.
3. Retain Instructions
The safety and operating instructions should be retained for future reference.
4. Notice Warnings
All warnings on the product and in the operating instructions should be adhered to.
5. Cleaning
Disconnect the unit from the mains before cleaning the unit. Do not use abrasive cleaners. Use a damp
cloth ONLY for cleaning.
6. Water and Moisture
Operating Instructions3
SFP-H-7 SERIES with PIPM-R-7-TypeC
3
Re-imagine Beyond Technology sales@plurainc.com
Do not use this product near water surface.
7. Transporting Product
This product should be moved with care. Quick stops, excessive force and uneven surfaces may cause the
product damages.
8. Accessories
Do not use accessories not recommended by PLURA Inc. as they may cause hazards.
9. Ventilation
Do not block any of the ventilation openings.
Install in accordance with the manufacturer’s instructions.
10. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply, consult your power supply company.
11. Power Lead Polarization
This product is equipped with a three-wire grounding-type cord. This is a safety feature. Do not use any
other type power cord.
12. Power Cord Protection
Power-supply cords should be dressed so that they are not likely to be pulled or pinched by items placed
upon or against them.
13. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet. This will prevent possible damage to the product
due to lightning and power-line surges.
14. Grounding the product
This product must be grounded properly to comply with the safety regulations in the country of use. If you
are unsure of these regulations, please consult a qualified electrician.
15. Servicing
Do not attempt to service this product by yourself as opening or removing covers may expose you to
dangerous voltages or other hazards. Refer all servicing to qualified service personnel.
16. Damage Service Required
Isolate this product from the mains and refer to qualified service personnel under the following conditions:
A. If the power-supply cord or plug is damaged.
B. If the front LCD front has been damaged.
C. If the product does not operate correctly by following the operating instructions. Use only the user
control buttons any improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to its normal operation.
D. If the product has been dropped.
Operating Instructions4
SFP-H-7 SERIES with PIPM-R-7-TypeC
4
Re-imagine Beyond Technology sales@plurainc.com
E. If the product exhibits a distinct change in performance.
17. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition and the warranty seal is provided.
18. Mounting
The product should be mounted on a wall as recommended in the instructions.
19. Power
This set operates on an AC supply; the voltage is as indicated on the label on the Manual. This appliance
must be earthed at all times through the chassis as well as through the power lead.
Operating Instructions5
SFP-H-7 SERIES with PIPM-R-7-TypeC
5
Re-imagine Beyond Technology sales@plurainc.com
1. OVERVIEW
Plura SFP-H-7 series with Type C Plura IP platform is the industry’s trusted TRUE-IP 10GbE
broadcast & media monitor solution, supporting uncompressed FHD based on SMPTE ST 2110,
ST 2022-6Ŧ & ST 2022-7 and supports up to 1920 x 1080 resolutions.
The flexibility and robustness of the SFP-H-7 platform is the ultimate solution for a wide range
of broadcast and professional media SDI to IP transition projects. The SFP-H-7 platform is a
powerful hybrid solution supporting SFP+ 10G (ST 2110, ST 2022-6Ŧ, ST 2022-7), 3G & 1.5G &
HDM I 1.4 connectivity.
2. GENERAL FEATURES
●Dual 10 GbE SFP+ interfaces as
MEDIALAN1 and MEDIALAN2
●Two generic compatible 10G-SR SFP+
850nm digital optical monitoring
LC MMF optical transceiver modules
included
●Dual 10GbE De-Encapsulation channels
are fully compatible with many MM and
SM SFP modules manufactures
●1 x 3G/1.5G loop output for MEDIALAN1
main ST 2110Ŧ support
●1 x 3G/1.5G Aux/2nd channel ST 2110Ŧ
support
●Supports ST 2110, ST 2022-6Ŧ, ST
2022-7 & PTP/ST 2059 V2
●ST 2110-10, System architecture and
synchronization: essences, RTP, SIP and
PT P
●ST 2110-20, Uncompressed video
transport, Wide / Narrow types
●ST 2110-21, Traffic shaping and network
delivery timing
●ST 2110-30, Audio transport profile level
C, 16CH, 48Khz sample rate, 1ms/.125µs
●ST 2110-40, Transport of ancillary data
●ST 2022-7 seamless protection
switching providing data loss protection
●SMPTE ST 2022-6Ŧ supported with
optional license
●Ember+, NMOS, JT-NM Interoperability
support
●Management Interface support (NMOS
& REST API In-band)
●Web UI / Ember+ Out-band control
support
●NMOS IS-04 discovery and registration
●NMOS IS-05 device connection
management
●JT-NM NMOS certification support
●JSON snippet for NMOS control support
●Ember+ monitor control support with
extensive Ember+ tree control
●Session Description Protocol “SDP” file
support
●IGMP V2 & V3 support
●Plura web user interface “UI” support
●Supports Coaxial 3G/1.5G BNC I/O
connectivity
●Supports Coaxial SFP I/O connectivity
●2xSFP+ cage supporting 10G/3G/1.5G
SDI
●1 x HDMI 1.4 input port
●Supports up to 1920 x 1080 resolutions
●RGB 12 bit Digital Signal Processing
●178 degree Viewing Angle Display
●Gamma Selectable ( 0.8 – 3.0)
●Color Temperature – User, VAR,
Adjustable (11000K TO 3200K)
●(ICAC) – Plura Intelligent Connection for
Alignment & Calibration
●Display Advanced Waveform & Vector
Scope simultaneously with line select
●Various and User defined Markers
Display & Safe Area
●Programmable 6 User Front Pushbutton
Controls & GPI
●Closed Caption (608/708) N. American
Market
●Cutting edge De-interlacing and scaling
Technology
●Fast Response Time for high motion
video
●Internal Monitor Display (IMD)
●Ethernet & RS232 Remote Control
●Ember+ compliant control system
capabilities
●Underscan / Overscan / Normal / Zoom
●Pixel to Pixel Mode, Tally, DC operation
●False Color and Peaking Filter / Focus
Assist
●Video Range test with adjustable Y & C
values
●Display LTC & DIVTC time code with line
select
●Embedded Audio input, Digital Audio
Decoding
●Internal Pattern Generator and Wall
Control System
Operating Instructions6
SFP-H-7 SERIES with PIPM-R-7-TypeC
6
佧
optional
Re-imagine Beyond Technology sales@plurainc.com
The SFP-H-7 provides comprehensive interoperability capabilities with wide range of third-party IP-FHD media platforms with a seamless end-
to-end production workflow. It can decode multiple SMPTE 2110 & 2022-7 media streams within any broadcast and professional media SDI &
IP 2110 infrastructures.
1026 ,1
Band PHGLD
Control MEDIALAN
Server
10 GigE BACKUP
MAIN Switch 10 GigE
Plura PTP Generator
IEEE 1588-2008 PTPv2 BACKUP Switch 10 GigE
10 GigE MAIN
I36WUHDP3*
IP-Stream-3G
Plura SFP-H-7 monitors are equipped with two generic compatible 10G-
SR SFP+ 850nm digital optical monitoring LC MMF optical transceiver
modules. Dual 10GbE De-Encapsulation channels are fully compatible
with MM and SM SFP modules manufactures. For further details, please
contact Plura tech support.
(PEHU Out-
Band PRQLWRU
Control
CONTROL
LAN
PLURA Out-Band
8VHUInterface Control
SFP-324-H-7 displaying
MEDIALAN Stream Main
SFP-324-H-7 Interface I/O
M(',$/$1 Main
Loop Output 3G
PBM-317-3G Monitor
displaying MEDIALAN
VWUHDP$0DLQLoop out
3G SD,from 6)3324H-7
3. Production Workflow and I/O Connections
1) Production Workflow
Operating Instructions7
SFP-H-7 SERIES with PIPM-R-7-TypeC
7
佧
optional
Re-imagine Beyond Technology sales@plurainc.com
●SFP-324-H-7 / Front Keypad
Figure 1. SFP-324-H-7 Monitor
Figure 2. Front Keypad - Select and Display the PIPM-R-7 IP Stream
(When PIPM-R-7 is installed inside SFP-H or SFP-H-7 unit)
►Select PIPM as Input channel and then select Main or SUB as Output channel.
●Front Keypad Operations
Key Name Operation
STANDBY ►Power ON/OFF Button. This button is operated after being pressed about
3 seconds.
INPUT
SFP1/SFP2/SDI/PIPM
►SFP Modules Input CH selected.
►Channels in the input signal, the key led light.
►Select PIPM as Input channel when PIPM-R-7 is installed
OUTPUT
SFP1/SFP2/SDI/AUX/
MAIN/SUB ►SFP Modules Output CH selected.
ALL ►SFP Modules ALL Output CH selected.
FUNCTION
F1/F2/F3
►Executes functions of user selected.
UNDEF, Aspect, Mono/Blue only, Audio Channel, Safety area marker, Time
code, Analog Caption, Audio mute, Still image, Zoom, Flip, Gamma select,
PIP func & Input, Sub win full, Sub win part
SEL/INPUT
►Activates OSD menu of input source selecting.
►Changes input source by selecting.
►Executes functions (by OSD help commands) in main OSD menu.
►Activates child menu.
MENU
►Activates main OSD menu.
►Navigates higher menu in main OSD menu.
►Exits OSD menu.
Adjust
►Adjust Picture Menu(Brightness -> Contrast -> Color -> Sharpness->Phase
& Tint)
►Turn Right (with „UP' button is same)
►Turn Left (with „DOWN' button is same)
Table 1. Front Keypad Operations
Operating Instructions8
SFP-H-7 SERIES with PIPM-R-7-TypeC
8
Re-imagine Beyond Technology sales@plurainc.com
2) I/O & Connectivity
Figure 3. I/O & Connectivity
PIPM-R-7 I/O Description
Ethernet Port ►Control LAN out-band
Dual SFP+ GigE Ports ►2x 10 GigE SFP+ cages for media LAN
SDI AUX O/P ►1EA Serial Digital , 3Gb/s, 1.485Gb/s, 270Mb/s, BNC Jack
Table 2: SFP-H-7 (PIPM-R-7) I/O
Operating Instructions9
SFP-H-7 SERIES with PIPM-R-7-TypeC
9
Re-imagine Beyond Technology sales@plurainc.com
4. INSTALLATION OVERVIEW
1) Initial Setup by Web Browser
All Plura monitors should be shipped with the latest versions of firmware/software at the time
of production, but in the case where an update is available, follow the appropriate steps below,
Each update is applied using the Control LAN UI. The Media LAN 2110 Control (out-band) is
also accessed via the Control LAN UI. Follow the instructions below to access this interface.
Chrome and Firefox browsers are recommended for control on Windows.
2) Connecting to the Control LAN User Interface “UI”
●Plug in the Ethernet cable to the Control LAN on the back of the monitor.
●Power on the unit and wait for the “PLEASE WAIT EMBER+ BOARD IS BOOTING”
message to go away (Figure 4)
Figure 4. Ember+ Board Booting
●On your Plura monitor, press the “Menu” button.
Select “Setup” →“Advanced” →“Network Config” to find the IP address of the Ember+
board (Figure 5).
Figure 5.
Plura Monitor
Network Config
Menu
Operating Instructions10
SFP-H-7 SERIES with PIPM-R-7-TypeC
10
Inhaltsverzeichnis
Andere Plura Steuereinheit Handbücher
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
