PMK TK100C Bedienungsanleitung
TK100C
Probe Calibrator
Instruction Manual
2
Copyright © 2014 PMK GmbH All rights reserved.
Information in this publication supersedes that in all previously published material.
Specifications are subject to change without notice.
Manufacturer
PMK Mess- und Kommunikationstechnik GmbH
Königsteiner Str. 98
65812 Bad Soden, Germany Internet: www.pmk.de
Fax: +49 (0) 6196 5927 - 939
Warranty
PMK GmbH warrants this oscilloscope accessory for normal use and operation within specifications for a peri-
od of two (2) years from date of shipment and will repair or replace any defective product which was not dama-
ged by negligence, misuse, improper installation, accident or unauthorized repair or modification by the buyer.
This warranty is applicable only to defects due to material or workmanship. PMK GmbH disclaim any other
implied warranties of merchantability or fitness for a particular purpose. PMK GmbH will not be liable for any
indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business,
loss of use or data, interruption of business and the like), even if PMK GmbH has been advised of
the possibility of such damages arising from any defect or error in this manual or product.
3
WEEE/ RoHS Directives TK100C
(EC conformity marking)
This electronic product is classified within the WEEE/ RoHS* category list as monitoring and control
equipment (category 9). Category 9 products are exempted from the restrictions under the scope of the
RoHS directive.
Your help and efforts are required to protect and keep clean our environment. Therefore return this
electronic product at the end of its life either to the manufacturer or take care of separate WEEE
collection and professional WEEE treatment yourself. Do not dispose as unsorted municipal waste!
* EC Directives:
WEEE Directive 2002/96/EC - Waste Electrical and Electronic Equipment
RoHS Directive 2002/95/EC - Restriction of the use of certain Hazardous Substances
in Electrical and Electronic Equipment
Safety Symbols
The following symbols may appear on the product or in this instruction manual:
Caution, risk of danger. Refer to manual.
Caution, risk of electric shock.
Earth (ground) TERMINAL.
4
Safety Information TK100C
To avoid personal injury and to prevent fire or damage to this product or products connected to it, review and
comply with the following safety precautions. Be aware that if you use this instrument in a manner not specified
the protection this product provides may be impaired.
Only qualified personnel should use this instrument.
Warning:
Dangerous voltages capable of causing death are present when using this instrument.
Use extreme caution when handling, testing and adjusting.
Use only grounded instruments.
Connect the generator only to equipment that is connected to earth ground. Always make sure equipment is
grounded properly.
Keep away from live circuits.
Avoid open circuitry. Do not touch connections or components when power is present.
Do not operate with suspected failures.
Refer to qualified service personnel.
Indoor use only.
Do not operate in wet/damp environment. Keep product surfaces dry and clean.
Do not operate the product in an explosive atmosphere.
Do not modify the instrument.
5
About the TK100C Probe Calibrator TK100C
The TK100C facilitates DC, LF and HF adjustment of HV-probes.
Mode of operation
The function of TK100C can be seen from the circuit principle.
A stabilized 100 V DC source loads a 1 uF capacitor. A "none chatter contact" connects the voltage to a RC
network of approx. 50 Ωand 47 pF. The rise time between 10% and 90% is approx smaller 6 ns. The duration
of the square wave pulse is 5 ms.
For optimum results the HV-probe or divider should be connected coaxial.
Picture 1: circuit principle
100 V 47 pF
„none chatter contact“
ca. 50 Ohm
1 µF
OUTPU
T
6
How to use this instrument TK100C
Setup:
1. Connect the probe calibrator to the power supply and the power supply to mains.
NOTE: The Power LED (2) is lit,
The Mode Indicator LED (3) is off.
There is no voltage applied to the BNC Output (4)
2. Connect the probe to the BNC jack of the measuring instrument and adjust the scope-to-probe
divider ratio.
4. Connect the probe to the BNC Output (4) of the TK100C
Operation:
- By pressing the Mode Button (5) once, the TK100C provides a 100 V square wave signal of 5 ms duration.
NOTE: The TK100C is in pulse mode. The Mode Indicator LED (3) blinks.
- By pressing the Mode Button (5) again the TK100C is set to DC Mode, providing 100 V DC
NOTE: The Mode Indicator LED (3) glows constantly.
- If the Mode Button (5) is pressed again the TK100C will go into Standby once again.
NOTE: The Mode Indicator LED (3) is turned off again.
Make sure to set the trigger level at the scope to a decent value for best results.
( e.g. 50% of the pulse amplitude)
1 Input Supply Voltage 15 V DC
2 Power LED
3 Mode LED
4 Output BNC Connector
5 Mode Button
6 Trimmer Potentiometer
7 IdenticationLabel
7
Calibration TK100C
The output voltage of the TK100C can be adjusted.
On the bottom side of the device is a trimmer potentiometer located under the identification label.
It is marked by the "DC Adjust" symbol.
Please note, that any previous calibration is invalidated by adjustments you make to this trimmer.
Safety Precautions & Override
The TK100C has a safety circuit inside, wich enables output voltage only if a BNC Adapter is connected.
You can override this safety feature at your own risk following these steps:
1. Disconnect the TK100C from the 15 V DC supply voltage.
2. Wait for at least 20 seconds.
3. Hold down the Mode Button (5) while reconnecting the 15 V DC supply voltage.
The safety circuit is now circumvented.
You can reenable the safety circuit by repeating the steps above, once again.
Specifications
Squarewave output voltage : +100 V ± 0.5%
Risetime : < 6 ns
Overshoot : < 3%
Repetition Rate : 100 Hz
Pulse Width: 5 ms
Dimensions: 135 x 30 x 70 mm
Weight: 120 g
Environmental Specifications
Altitude operating up to 2000 m
non-operating up to 15000 m
Temperature Range operating 0° C to +50° C
non-operating -40° C to +71° C
Maximum Relative Humidity operating 80 % relative humidity for temperatures up to +31° C,
decreasing linearly to 40 % at +50° C
Power Supply TK100C
Input: 100 - 240 V AC, 50 Hz/60 Hz
Output: 15 V DC
> 0.3 A
Connector
DC Line connector with 2.1 mm diameter hole and 5.5 mm outer diameter
Scope of Delivery
The following items are included in the scope of delivery. Please check the delivery for completeness. If any
item is missing, send a message to our sales department and we will send you this item immediately.
Item Qty
BNC Adapter 2.5 1
BNC Adapter 5.0 1
BNC Adapter 5.0-L 1
BNC Adapter 4 mm 1
Probe-Calibrator TK100C 1
Wall plug transformer 1
Set wall plug transformer primary adapters 1
(EU, US/JP, UK, AUS)
Trimmer Tool 1
Instruction Manual 1
M96-235-000 Revision F - February 2014
ø5.5
ø2.1
Inhaltsverzeichnis
Andere PMK Prüfgeräte Handbücher
PMK
PMK dataTec FireFly FF-1500 Bedienungsanleitung
PMK
PMK SONIC 4000 Bedienungsanleitung
PMK
PMK PHV Series Bedienungsanleitung
PMK
PMK KSZ 10B Bedienungsanleitung
PMK
PMK SKID eco Bedienungsanleitung
PMK
PMK HSDP Series Bedienungsanleitung
PMK
PMK SKID Bedienungsanleitung
PMK
PMK PHV 1000-O Bedienungsanleitung
PMK
PMK PML 111O Bedienungsanleitung
PMK
PMK SKID-S Bedienungsanleitung
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Hioki
Hioki 3169-20 Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung