PNI Wayfinder V2000 Bedienungsanleitung

OPERATION MANUAL

V2000

DIGITALVEHICLECOMPASS

Making Ordinary Products Extraordinary

You have purchased one of the most sophis-

ticated compasses available for use in a

vehicle. The Waynder V2000 is one of sev-

eral models using our latest technology to

make a digital compass easy and fun to

use, while still incorporating patented mag-

netic sensor technology to give you accurate

compass headings. PNI’s magnetic sensor

technology electronically measures your

vehicle’s magnetic eld and calibrates for

inaccuracies mathematically with its built-in

microprocessor. The result is unequaled com-

pass performance in a vehicle environment.

Features

• Patented magnetic sensor technology

same as the built-in compasses in GM,

Ford, and Chrysler vehicles.

• Bearing point stores one compass heading

at a time in memory to stay on desired

course.

• Inside or outside temperature in either

Fahrenheit or Celsius with temperature

sensor installed.

• ICE alert feature warns the driver to icy

road conditions when the temperature

sensor is installed outside.

CONGRATULATIONS!

• Automatic shut-off when no magnetic

eld changes have been sensed for

approximately 10 minutes.

• Programmable automatic backlight shut-

off feature.

• Photo diode light sensing feature turns

the backlight on or off depending on the

amount of ambient light when used with

12-volt adapter.

• Distortion warning when magnetic inter-

ference from outside sources is affecting

compass accuracy.

• Holographic LCD improves brightness

and contrast while removing glare.

• One-year warranty.

FEATURES

The manual is designed with procedures

organized in the order that they will be needed.

Additional information about procedures or

compass use can be found in our Frequently

Asked Questions section.

1. The LCD icons are written in capital

letters surrounded by quotes.

2. Buttons are indicated by a graphical icon

of each button, such as .

3. Procedures are organized so that the

action to perform follows the step

number and result of that action is

italicized.

4. “Press” means quickly press and release a

button in less than two seconds.

5. “Hold” means press and hold the button

for at least two seconds, or until a display

appears.

6. Indicates a warning or important

information.

7. Indicates a feature or optional equip-

ment available at additional cost.

CONVENTIONS USED IN THIS MANUAL

Display . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installing the Waynder V2000 . . . . . 7

Installing the battery . . . . . . . . . . . . .7

Installing the 12-volt adapter . . . . . .8

Installing the temperature sensor . . .8

Adjusting the mounting bracket . .10

Calibration . . . . . . . . . . . . . . . . . . . . . . 13

Bearing point mode . . . . . . . . . . . . . . 14

Temperature mode . . . . . . . . . . . . . . . 15

ICE alert feature . . . . . . . . . . . . . . . .16

Backlight mode . . . . . . . . . . . . . . . . . . 17

Photo diode feature . . . . . . . . . . . . .18

Optional accessories . . . . . . . . . . . . . 19

Frequently asked questions . . . . . . . 20

Service and replacement . . . . . . . . . . 24

Limited warranty . . . . . . . . . . . . . . . . 26

CONTENTS

DISPLAY

“DISTORTION” Cardinal Point Numeric Heading

Icon Readout Readout

Compass Rose Temperature and Buttons

Bearing Point Readout

Compass Front

Battery Photo Diode

Compartment

Temperature 12-Volt Power

Sensor Jack AdapterJack

Compass Back

When turned on, the unit displays heading in

one of 16 cardinal points (N, NNE, NE, ENE,

etc.), numeric digits with a resolution of 5°,

and a compass rose at all times. The compass

rose points in the direction displayed on the

cardinal point readout.

Buttons and icons

Light button

Press to turn the backlight on or off or

hold to set the backlight auto shut-off value.

Cal button

Press or hold to begin calibration process.

Temp button

Press to display the temperature or

hold to program the display for Fahrenheit

or Celsius values.

Point button

Press to display a stored bearing point

or hold to store a new bearing point.

Power button

Press to turn the Waynder V2000 on

or off.

“Distortion” icon

The “DISTORTION” icon displays when mag-

netic interference is compromising compass

accuracy or when a battery has been change.

DISPLAY

Step 1: Installing the battery

The unit uses a 3-volt CR123A lithium-type

battery, installed according to the diagram

on the inside of the battery compartment.

Push the battery straight down into the

compartment, not at an angle. To remove,

open the battery compartment.

Once the battery is inserted, the unit will cycle

through a quality test of two different displays.

The entire test lasts approximately 10 seconds,

then displays heading information. If any

of the two quality test screens display for

more than 30 seconds, remove the battery,

wait for approximately one minute, and then

reinsert the battery. Whenever the battery is

changed or removed, the V2000 will need to

be recalibrated.

The Waynder V2000 has an auto shut-off

feature. When no magnetic eld change has

been detected for approximately 10 minutes,

the compass automatically switches off and

saves all settings. No magnetic eld change

implies that the car is parked.

After installation, you must calibrate the

unit. As a reminder, the “DISTORTION”

icon will display in the upper left corner

until the unit is calibrated.

INSTALLING THE WAYFINDER V2000

Step 2: Installing the 12-volt adapter

Installing the 12-volt adapter is optional, but

recommended. Insert the small end into the

jack marked “POWER”, located on the back of

the compass and plug the large end into your

cigarette lighter receptacle.

Since cars do not always have constant

power supplied to the lighter receptacle,

you must keep a battery in the Waynder

V2000 at all times to allow the unit to

keep memory settings.

A 15-foot hardwire kit is available at

additional cost. See Optional Accessories

Step 3: Installing the temperature sensor

The included temperature sensor and tether

may be used outside or inside the vehicle.

Sensor placement inside the vehicle should

be somewhere out of direct sunlight and

away from your vehicle’s ventilation system,

where there is natural airow to the sensor.

Sensor placement for outside temperature

should also be away from direct sunlight and

engine heat in a place where there is natural

air ow to the sensor, such as in the grill

area or door jamb. Every vehicle is different,

making it impossible to list all possible sensor

locations.

INSTALLING THE WAYFINDER V2000

Andere Handbücher für Wayfinder V2000

Inhaltsverzeichnis

Andere PNI Kompass Handbücher

PNI

PNI Wayfinder V700 Bedienungsanleitung

PNI

PNI Corsa X441 Bedienungsanleitung

PNI

PNI V1000 Bedienungsanleitung

PNI

PNI V550 Bedienungsanleitung

PNI

PNI V6000 Bedienungsanleitung

PNI

PNI V550 Bedienungsanleitung

PNI

PNI Wayfinder Gebrauchs- und Pflegehandbuch

PNI

PNI V500 Bedienungsanleitung

PNI

PNI Wayfinder V2000 Bedienungsanleitung

Beliebte Kompass Handbücher anderer Marken

Silva

Silva EXPLORER 203 Bedienungsanleitung

Quechua

Quechua C Quechua 400 Bedienungsanleitung

Brunton

Brunton 54lu Bedienungsanleitung

Raymarine

Raymarine ST40 Bedienungsanleitung

Advanced Navigation

Advanced Navigation GNSS Compass Bedienungsanleitung

Brunton

Brunton 85R Handbuch

Brunton

Brunton 9020G Kurzanleitung zur Einrichtung

Furuno

Furuno SC-30 Bedienungsanleitung

Suunto

Suunto KB-14/360 Bedienungsanleitung

Conrad

Conrad 67 13 02 Bedienungsanleitung

Brunton

Brunton NOMAD V2 PRO Bedienungsanleitung

Bushnell

Bushnell Digital Navigation 70-0002 Bedienungsanleitung

Dakota Digital

Dakota Digital Odyssey ODY-17-1 Bedienungsanleitung

Brunton

Brunton 16B Braille Bedienungsanleitung

Freestyle

Freestyle TOUCH COMPASS Bedienungsanleitung

True North

True North Revolution Bedienungsanleitung

TECHTRAIL

TECHTRAIL Trailhead Bedienungsanleitung

Furuno

Furuno Sc 50 Bedienungsanleitung