Poly Rove R8 Bedienungsanleitung
Rove R8 REPEATER USER GUIDE
Trademarks
the combinations of its logo thereof are trademarks of Poly
Other product names used in this publication are for identification purposes and maybe the trademarks of their
respective companies.
Disclaimer
The contents of this document are provided about Poly products. Poly makes no representations with respect to
completeness or accuracy of the contents of this publication and reserves the right to make changes to product
descriptions, usage, etc., at any time without notice. No license, whether express, implied, to any intellectual property
rights are granted by this publication
Confidentiality
This document should be regarded as confidential, unauthorized copying is not allowed
Introduction:
The Rove R8 repeater user guide is designed to give a detailed overview on how to install, register and manage Poly
repeaters
Document History
REVISION AUTHOR ISSUE DATE COMMENTS
1.0 MLE 16-09-2020
What is new
What new features have been added.
VERSION
FEATURE
V
515
Main topics:
Installation
Locate automatic
Manual registration
Firmware update
LED indications
Installation of Repeater
After planning the network, next is to determine the proper places or location the repeater. The repeater should be
mounted as high as possible (2 meters or higher).
3.1 Package – Contents/Damage Inspection
Before Package Is Opened:
Examine the shipping package for evidence of physical damage or mishandling prior to opening. If there is a proof of
mishandling prior to opening, you must report it to the relevant support center of the regional representative or
operator.
Contents of Package:
Make sure all relevant components are available in the package before proceeding to the next step.
Every shipped repeater package/box contains the following items:
1 x Power supply
1 x Repeater
1 x Table stand
1 x Safetysheet
Damage Inspection:
The following are the recommended procedure for you to use for inspection:
1. Examine all relevant components for damage.
2. Make a “defective on arrival – DOA” report or RMA to the operator. Do not move the shipping carton until
the operator has examined it. If possible, send pictures of the damage. The operator/regional representative
will initiate the necessary procedure to process this RMA. They will guide the network administrator on how
to return the damaged package if necessary.
3. If no damage is found, then unwrap all the components and dispose of empty package/carton(s) in
accordance with country specific environmental regulations.
3.2 Poly Base Station Mechanics
The repeaters front end shows an LED indicator that signals different functional states of the repeater.
The indicator is off when the repeater is not powered on.
Hardware installation:
The repeater should be mounted on a wall in a height less than 2 meters.
Screws and Anchors needed (Not supplied by Poly)
2x Screws = Screw wall mount M3.5x31
2x Anchors: Length 29,6mm, OD 6,0mm, ID 4,8mm
NOTE: The repeater should be mounted on a wall not higher than 2 meters
3.4 Recommended external DC adapters
Part Nr Description Manufacturer Type
S005CAV0500100
SMPS,100-240VAC,5V 1000mA with
USB-A
Ten Pao International LTD
EU
S005CAB0500100 UK
S005CAS0500100 AU
S005CAU0500100
US
Repeater registration options:
There are 2 different ways to register Poly repeater’s “Local Automatic” and “Manually”
Local Automatic:
In this mode the repeater registers to the base station with best signal strength, this option is only recommended for
single cell systems and Multi cell systems where the repeater is only able to sync with one specific base station.
Manually:
Manual registration is used in most cases when adding repeaters to a multi cell system. Manual registration allows to
determine what base stations the repeater must connect to.
Register repeater(s) “Local Automatic”:
NOTE: Do not power on the repeaters before they have been added on the base station
NOTE: When adding first repeater the base station(s) will reboot, this is because encryption is being enabled, the
same goes if all repeaters is deleted, then the system will reboot to disable encryption.
Step 1: To register repeater(s), navigate to the Repeater page.
Screen shot
Step 2: Click” Add Repeater” and select “Local Automatic” from the dropdown
Screen shot
Step 3: Give the repeater a name and press “save”
Step 4: Power on the repeater(s) and registration will start.
When the LED is steady green the repeater is successfully registered.
Screen shot
PARAMETERS DESCRIPTION
IDX System counter
RPN
SINGLE CELL SYSTEM:
The base has always RPN00, first repeater will then be RPN01, second repeater RPN02
and third RPN03 (3 repeaters maximum per base)
MULTI CELL SYSTEM:
Bases are increment by 2^2 in hex, means first base RPN00 second base RPN04 etc., in
between RPN01, 02, 03 addressed for repeaters at Primary base and 05, 06, 07 addressed
for Secondary base (3 repeaters maximum per base)
NAME/IPIE Name and IPIE number of the repeater
DECT SYNC MODE DECT Sync mode – Manually or Automatic
STATE State of the repeater Enabled/Disabled
FW INFO Firmware version
FWU PROGRESS How many percentages of the firmware is loaded / Off if no firmware is being loaded
Register repeater(s) “Manually”:
NOTE: Do not power on the repeaters before they have been added on the base station
NOTE: When adding first repeater the base station(s) will reboot, this is because encryption is being enabled, the
same goes if all repeaters is deleted, then the system will reboot to disable encryption.
Step 1: To register repeater(s), navigate to the Repeater page.
Screen shot
Step 2: Click” Add Repeater” and select “Manually” from the dropdown
Screen shot
Step 3: Give the repeater a name and press “save”
Step 4: select what base station the repeater needs to register to “DECT sync source” drop down
In this case there are three base stations in the multicell (RPN00, RPN04 and RPN08) and three repeaters can be
connected to each base station.
Select the base station the repeater needs to register to.
E.g. RPN04
Screen shot
Step 5: Select the RPN for the repeater.
ERROR: The repeater will choose the first available slot on the selected base station.
RPN x: The repeater connects to RPN x of the chosen base station.
E.g. Base station RPN04 + RPN1 repeater, then the repeater connects to “RPN5”
Screen shot
Firmware update:
The repeaters are updated over air.
Step 1: Navigate to Firmware Update page
Step 2: Enter “Firmware Update server address”, “Firmware path” and DECT402x firmware version
Screen shot
Inhaltsverzeichnis
