Polycom VBP 7301 Handbuch

14.1.1 |March 2015 | 3725-78313-001A

HARDWARE INSTALLATION GUIDE

Polycom®Video Border Proxy

(VBP™) 7301

language or format, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the

express written permission of Polycom, Inc.

6001 America Center Drive

San Jose, CA 95002

USA

Trademarks Polycom®, the Polycom logo and the names and marks associated with Polycom products are

trademarks and/or service marks of Polycom, Inc. and are registered and/or common law marks in the United States

and various other countries.

All other trademarks are property of their respective owners. No portion hereof may be reproduced or transmitted in any

form or by any means, for any purpose other than the recipient's personal use, without the express written permission

of Polycom.

End User License Agreement By installing, copying, or otherwise using this product, you acknowledge that you

have read, understand and agree to be bound by the terms and conditions of the End User License Agreement for this

product. The EULA for this product is available on the Polycom Support page for the product.

Patent Information The accompanying product may be protected by one or more U.S. and foreign patents and/or

pending patent applications held by Polycom, Inc.

Open Source Software Used in this Product Thisproductmaycontainopensourcesoftware.Youmayreceive

the open source software from Polycom up to three (3) years after the distribution date of the applicable product or

software at a charge not greater than the cost to Polycom of shipping or distributing the software to you. To receive

software information, as well as the open source software code used in this product, contact Polycom by email at

[email protected].

Disclaimer While Polycom uses reasonable efforts to include accurate and up-to-date information in this document,

Polycom makes no warranties or representations as to its accuracy. Polycom assumes no liability or responsibility for

any typographical or other errors or omissions in the content of this document.

Limitation of Liability Polycom and/or its respective suppliers make no representations about the suitability of the

information contained in this document for any purpose. Information is provided "as is" without warranty of any kind and

is subject to change without notice. The entire risk arising out of its use remains with the recipient. In no event shall

Polycom and/or its respective suppliers be liable for any direct, consequential, incidental, special, punitive or other

damages whatsoever (including without limitation, damages for loss of business profits, business interruption, or loss

of business information), even if Polycom has been advised of the possibility of such damages.

Customer Feedback We are striving to improve our documentation quality and we appreciate your feedback. Email

your opinions and comments to [email protected].

Polycom Support Visit the Polycom Support Center for End User License Agreements, software downloads,

product documents, product licenses, troubleshooting tips, service requests, and more.

Contents

1Components

Polycom VBP 7301 Front Panel . . . . . . . . . . . . . . . . . . . . . 3

Polycom VBP 7301 Back Panel . . . . . . . . . . . . . . . . . . . . . 4

Polycom VBP 7301 Ethernet LEDs . . . . . . . . . . . . . . . . . . . 5

Serial Craft Console Port Cable Pinout . . . . . . . . . . . . . . . . 6

Specifications and Certifications . . . . . . . . . . . . . . . . . . . . 7

2Physical Installation

Polycom VBP 7301 Shipping Contents . . . . . . . . . . . . . . . . 9

Desktop, Shelf, or Tray Installation . . . . . . . . . . . . . . . . . . 9

Rack-Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting the Power and Cables . . . . . . . . . . . . . . . . . . 11

Connecting to the Polycom VBP 7301 for the First Time. . . 11

ACompliance and Certifications

USA and Canadian Notices . . . . . . . . . . . . . . . . . . . . . . . 15

Class A Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

EEA Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . 18

Restriction of Hazardous Substances Directive (RoHS). . . . 19

End of Life Products . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

BLicensing and Warranty Information

Hardware Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Components

This guide provides an overview of the Polycom®VBP™ 7301 hardware

components, instructions for installing the device, and compliance and

certification notices. It also includes the hardware warranty.

Polycom VBP 7301 Front Panel

LED Indicator Description

Power Status Green Off – No Power, the system is off

On – Power is good, the system is on

Data Status Red Off – No data access to the IDE drive

On – Data is being written to the IDE drive

Polycom VBP 7301 Hardware Installation Guide

Polycom VBP 7301 Back Panel

Component Description

Erase Button One click—No action.

Two clicks—Resets the CLI and GUI password with no

service interruption.

Three clicks—Restores to factory default settings and

reboots the system.

VGA Port Currently not used

Port 6, Port 5, Port 4 Currently not used

Port 3—Management

Interface 1 x 10/100/1000 Mbps RJ-45 Ethernet port for optional

management network connectivity. This interface must not

be on the same network as the WAN or LAN subnets. This

network cannot be within a subnet contained in a “Route”

statement.

Port 2—WAN Interface 1 x 10/100/1000 Mbps RJ-45 Ethernet port for connectivity

to the WAN or Internet network connectivity. Default IP:

None

Port 1—LAN Interface 1 x 10/100/1000 Mbps RJ-45 Ethernet port for LAN

network connectivity. Default IP: 192.168.1.1

USB Ports Currently not used

Serial Craft Console Port 1 x RJ-45 serial craft console port for management.

9600-N-8-1 NONE for flow control. An RJ-45 to DB9

console cable is included in the box with the Polycom

VBP 7301.

Input Power Socket Accepts 3-pin shroud female plug for input power.

On/Off Switch System power on/off.

Polycom VBP 7301 Hardware Installation Guide Components

Polycom VBP 7301 Ethernet LEDs

Label Color Indication Status

ACT/Link Green On Ethernet port is receiving power.

Good link between the Ethernet port and the

connected switch.

Off The adapter and switch are not receiving power.

No connection between both ends of the network

cable. Check cable, replace cable.

Green Flashing The adapter is sending and receiving network data.

The frequency of the flashing varies with the

amount of data being transferred.

Speed Yellow On ACK/LINK LED must be on. This LED will show the

system operating at 1000 Mbps.

Green On ACK/LINK LED must be on. This LED shows the

system operating at 100 Mbps.

Off ACK/LINK LED must be on. This LED shows the

system operating at 10 Mbps.

Polycom VBP 7301 Hardware Installation Guide

Serial Craft Console Port Cable Pinout

The Polycom VBP 7301 is shipped with an RJ-45 to DB-9 cable (see

example below) for connecting the RJ-45 serial craft console port to a

computer to perform advanced configuration and debugging.

The RJ45-to-DB9 cable has the following pinout.

Specifications and Certifications

PIN DB9 Signal DB9 to RJ45 RJ45 Signal PIN

1DTR Pin 1 to Pin 2 RTS 1

2TXD Pin 2 to Pin 3 DTR 2

3RXD Pin 3 to Pin 6 TXD 3

4DSR Pin 4 to Pin 7 GND 4

5GND Pin 5 to Pin 4 and Pin 5 SGND 5

6DTR Pin 6 to Pin 2 RXD 6

7CTS Pin 7 to Pin 8 DSR 7

8RTS Pin 8 to Pin 1 CTS 8

Item Description

Ethernet Ports 6 x 10/100/1000 Ethernet

Serial Ports 1 x RJ-45 serial craft console port for management

Dimensions W: 437.8mm / 17.2” x D: 445mm / 17.5” x H: 44mm / 1.73” (1U)

Weight 12.75 lbs

Polycom VBP 7301 Hardware Installation Guide Components

Power 100/240v VAC - auto-selecting, 50 to 60 Hz - 200W MAX AC

Input - BTU/h = 682

Warranty 3 Years

Environmental

Requirement Operating Temperature: 0° to 40°C

Relative Humidity 10% to 90%, non-condensing

Certifications RoHS Compliant

WEEE Compliant

Safety UL/cUL, LVD, Gost-R, Mexico CoC, UL-AR

Emissions FCC Part 15 Class A, ICES-003, VCCI Class A, KCC, CCC, C-tick,

BSMI, ANATEL

Immunity CE

MTBF 7301= 96,000 hrs

Physical Installation

The Polycom®VBP™ 7301 is designed for desktop, shelf, tray, or rack

installation. Observe the following guidelines when installing the system:

Always verify that the AC cord is disconnected from a power source prior to

installation.

Do not stack multiple units on top of each other as this can cause

overheating.

Ensure that the installation site has adequate air circulation and meets the

minimum operating conditions for the system as specified in Compliance

and Certifications.

Polycom VBP 7301 Shipping Contents

The Polycom VBP 7301 is shipped with the following components:

Polycom VBP 7301 appliance

Rack mount kit

AC Power Cord

RJ-45 to DB-9 serial craft console port cable

Desktop, Shelf, or Tray Installation

1. Remove the Polycom VBP 7301 and accessories from the shipping

container.

2. Place the Polycom VBP 7301 on a flat, dry surface such as a desktop, shelf,

or tray.

Polycom VBP 7301 Hardware Installation Guide

Rack-Mount Installation

You can install the Polycom VBP 7301 in a 19” rack using the rack mount kit

supplied with the product.

Note

Important

Before installing the device in a rack, take note of the following conditions:

Elevated Operating Ambient—If installed in a closed or multi-unit rack

assembly, the operating ambient temperature of the rack environment may be

greater than room ambient. Therefore, consideration should be given to

installing the equipment in an environment compatible with the maximum

ambient temperature specified by the manufacturer.

Reduced Air Flow—Installation of the equipment in a rack should be such

that the amount of airflow required for safe operation of the equipment is not

compromised.

Mechanical Loading—Mounting of the equipment in the rack should be such

that a hazardous condition is not achieved due to uneven mechanical loading.

Circuit Overloading—Consideration should be given to the connection of the

equipment to the supply circuit and the effect that overloading of the circuits

might have on overcurrent protection and supply wiring. Appropriate

consideration of equipment nameplate ratings should be used when addressing

this concern.

Reliable Earthing—Reliable earthing of rack-mounted equipment should be

maintained. Particular attention should be given to supply connections other

than direct connections to the branch circuit (for example, use of power

strips).

Install the Polycom VBP 7301 in a Rack

1. Attach the rack mount ears to both sides of the Polycom VBP 7301 chassis

with the supplied screws.

2. Install the chassis in the rack with rack mount screws (not included).

Inhaltsverzeichnis

Andere Polycom Konferenzsystem Handbücher

Polycom

Polycom RealPresence Trio 8500 Bedienungsanleitung

Polycom

Polycom realpresence trio 8800 Technisches Datenblatt

Polycom

Polycom RealPresence Medialign 255 Bedienungsanleitung

Polycom

Polycom ViewStation vsx7000 Bedienungsanleitung

Polycom

Polycom CX5500 Bedienungsanleitung

Polycom

Polycom SoundPoint IP 335 Bedienungsanleitung

Polycom

Polycom RealPresence Medialign 255 Bedienungsanleitung

Polycom

Polycom V500 Bedienungsanleitung

Polycom

Polycom ViaVideo Betriebshandbuch

Polycom

Polycom RealPresence RMX 4000 Montageanleitung

Polycom

Polycom G7500 Bedienungsanleitung

Polycom

Polycom QDX 6000 System Bedienungsanleitung

Polycom

Polycom V500 Bedienungsanleitung

Polycom

Polycom VIEWSTATION EX Bedienungsanleitung

Polycom

Polycom HDX Desktop Systems Bedienungsanleitung

Polycom

Polycom RealPresence Group Series Montageanleitung

Polycom

Polycom ViewStation vsx7000 Bedienungsanleitung

Polycom

Polycom SpectraLink 6000 System Bedienungsanleitung

Polycom

Polycom QDX 6000 System Service-Handbuch

Polycom

Polycom RealPresence Group 300 Gebrauchsanweisung

Polycom

Polycom 1725-22886-001/A Bedienungsanleitung

Polycom

Polycom VSX 3000 Bedienungsanleitung

Polycom

Polycom 9.0.6 Bedienungsanleitung

Polycom

Polycom HDX 4000 Series Bedienungsanleitung

Beliebte Konferenzsystem Handbücher anderer Marken

Kramer

Kramer VIA GO Bedienungsanleitung

AVT

AVT MAGIC AC1 Go Bedienungsanleitung

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung

Sony

Sony PCS-I150 Bedienungsanleitung

Middle Atlantic Products

Middle Atlantic Products VTC Series Bedienungsanleitung

Prentke Romich Company

Prentke Romich Company Vanguard Plus Leitfaden

Speakerbus

Speakerbus iD 712 Bedienungsanleitung

Trelleborg

Trelleborg SafePilot CAT PRO Bedienungsanleitung

Sennheiser

Sennheiser ADN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 7100 Bedienungsanleitung

AINA

AINA PTT Voice Responder Bedienungsanleitung

Yamaha

Yamaha ProjectPhone PJP-100H Bedienungsanleitung

vissonic

vissonic VLI Series Bedienungsanleitung

Panasonic

Panasonic KX-VC500 Bedienungsanleitung

Poly

Poly Trio 8300 Bedienungsanleitung

Crestron

Crestron Mercury CCS-UCA-SMK Maßzeichnung

Inmarsat

Inmarsat mini M Bedienungsanleitung

Tenveo

Tenveo ALL-IN-ONE Bedienungsanleitung