Porter-Cable 90546382 Bedienungsanleitung

VS Orbital Jig Saw

www.portercable.com

INSTRUCTIVO DE OPERACIÓN,

CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA.

ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL

PRODUCTO.

CATALOG NUMBER

PC600JS

Instruction manual

Manuel d'instructions

Manual de'instrucciones

Scie sauteuse orbitale à vitesse variable

Sierra caladora de acción orbital y

velocidad variable

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 1

General Safety Rules

Read all instructions. Failure to follow all instructions listed

below may result in electric shock, fire and/or serious injury. The term “power

tool” in all of the warnings listed below refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

SAVE THESE INSTRUCTIONS

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the

presence of flammable liquids, gases or dust.

Power tools create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions

can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes,

radiators, ranges and refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging

the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric

shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating

a power tool. Do not use a power tool while you are tired or under the

influence of drugs, alcohol or medication.

A moment of inattention while

operating power tool may result in serious personal injury.

b) Use safety equipment. Always wear eye protection.

Safety equipment such as

dust mask, non-skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the switch is in the off-position before

plugging in.

Carrying power tools with your finger on the switch or plugging in

power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables

better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,

clothing and gloves away from moving parts.

Loose clothes, jewelry or long hair

can be caught in moving parts. Air vents often cover moving parts and should also

be avoided.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of these devices

can reduce dust-related hazards.

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 2

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power tool,

taking into account the working conditions and the work to be performed.

Use of the power tool for operations different from those intended could result in a

hazardous situation.

5) Battery tool use and care

a) Ensure the switch is in the off position before inserting battery pack.

Inserting

the battery pack into power tools that have the switch on invites accidents.

b) Recharge only with the charger specified by the manufacturer.

A charger that is

suitable for one type of battery pack may create a risk of fire when used with

another battery pack.

c) Use power tools only with specifically designated battery packs.

Use of any

other battery packs may create a risk of injury and fire.

d) When battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that can

make a connection from one terminal to another.

Shorting the battery terminals

together may cause burns or a fire.

e) Under abusive conditions, liquid may be ejected from the battery, avoid

contact. If contact accidentally occurs, flush with water. If liquid contacts

eyes, additionally seek medical help.

Liquid ejected from the battery may cause

irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

•Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a

"live" wire will make exposed metal parts of the tool "live" and shock the operator.

•Use clamps or another practical way to secure and support the work piece to a

stable platform. Holding the work by hand or against your body leaves it unstable and

may lead to loss of control.

• Keep hands away from cutting area. Never reach underneath the material for any

reason. Hold front of saw by grasping the contoured gripping area. Do not insert fingers

or thumb into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the

saw by gripping the shoe.

• Keep blades sharp. Dull blades may cause the saw to swerve or stall under

pressure.

• When cutting pipe or conduit ensure that they are free from water, electrical wiring,

etc.

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 3

• Allow the motor to come to a complete stop before withdrawing the blade from the

kerf (the slot created by cutting). A moving blade may impact the workpiece causing a

broken blade, workpiece damage or loss of control and possible personal injury.

• Never hold work in your hand, lap or against parts of your body when sawing. The

saw may slip and the blade could contact the body causing injury.

• Keep handles dry, clean, free from oil and grease. This will enable better control of the

tool.

• Clean out your tool often, especially after heavy use. Dust and grit containing metal

particles often accumulate on interior surfaces and could create an electric shock hazard.

• Do not operate this tool for long periods of time. Vibration caused by the operating

action of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to

provide extra cushion, take frequent rest periods, and limit daily time of use.

ALWAYS

use safety glasses. Everyday eyeglasses are NOT safety

glasses. Also use face or dust mask if drilling operation is dusty. ALWAYS WEAR

CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CPA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NOSH/OSHA respiratory protection.

Some dust created by power sanding, sawing, grinding, drilling, and other

construction activities contains chemicals known to the state of California to cause

cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work.

To reduce your exposure to these chemicals: work in a well ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to filter

out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed

areas with soap and water.

Allowing dust to get into your mouth, eyes, or lay on the

skin may promote absorption of harmful chemicals.

Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury.

Always use NOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles away

from face and body.

Wear appropriate hearing protection during use. Under some

conditions and duration of use, noise from this product may contribute to hearing loss.

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Used without the safety alert symbol indicates a potentially hazardous

situation which, if not avoided, may result in property damage.

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 4

• When using an extension cord, be sure to use one heavy enough to carry the current

your product will draw. An undersized cord will cause a drop in line voltage resulting in

loss of power and overheating. The following table shows the correct size to use

depending on cord length and nameplate ampere rating. If in doubt, use the next

heavier gage. The smaller the gage number, the heavier the cord.

Symbols

• The label on your tool may include the following symbols. The symbols and their

definitions are as follows:

V..................volts A ..................amperes

Hz................hertz W..................watts

min ..............minutes ................alternating current

............direct current no ................no load speed

................Class I Construction ..................earthing terminal

(grounded) ................safety alert symbol

................Class II Construction .../min or rpm...revolutions or

(double insulated) reciprocation per minute

sfpm ............surface feet per minute

FUNCTIONAL DESCRIPTION

1. Trigger switch

2. Lock-on button

3. Saw blade locking lever

4. Saw blade

5. Shoe sleeve

6. Shoe

7. Shoe beveling lever

8. Speed control wheel

9. Cutting action lever

10. LED Light

SAVE THESE INSTRUCTIONS

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More Not more American Wire Gage

Than Than

0-6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 5

OPERATION

Before attempting any of the following operations, make sure that the

tool is switched off and unplugged and that the saw blade has stopped. Used saw blades

can be hot.

BLADE INSTALLATION (FIGURE B)

- Push the saw blade locking lever (3) upward.

- With teeth facing forward, insert the shank of the

saw blade into the blade holder as far as it will go.

- Release the lever.

- Check to ensure blade is secure before cutting.

ADJUSTING THE SHOE FOR BEVEL CUTS

(FIGURE C)

Never use the tool when the shoe is

loose or removed.

The shoe plate can be set to a left or right bevel angle

of up to 45°.

To set the bevel angle:

- Pull the shoe beveling lever (7) out and away from

the saw to unlock the shoe (6) as shown in figure C.

- Slide the shoe forward to release it from the 0°

positive stop position.

- The shoe can be beveled to the left or to the right

and has detents at 15°, 30° and 45°.

- Set the shoe to the desired bevel angle. Use a protractor to verify angle accuracy.

- Push the shoe beveling lever back towards the saw to lock the shoe.

To reset the shoe for straight cuts:

- Pull the shoe beveling lever (7) out and away from the saw to unlock the shoe (6) as

shown in figure C.

- Rotate shoe to an angle of approximately 0° and then pull shoe backwards to engage

the 0° positive stop.

- Push the shoe beveling lever back towards the saw to lock the shoe.

SWITCHING ON AND OFF

- To switch the tool on, squeeze the trigger switch (1).

- For continuous operation, squeeze the trigger switch then depress the lock-on button

(2). Once lock-on button is depressed, release the trigger switch.

- To switch the tool off, release the trigger switch. To switch the tool off, when in

continuous operation, squeeze the trigger and the lock will disengage.

VARIABLE SPEED CONTROL (FIGURE D)

A speed control wheel (8) is located on the top of the

saw. The speed increases as the wheel is turned

from a low speed setting of 1 to a high speed setting

of 7.

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 6

CUTTING ACTION – ORBITAL OR STRAIGHT

(FIGURE E)

Check that the tool is not locked ON

before connecting it to a power supply. If the trigger

switch is locked ON when the tool is connected to the

power supply, it will start immediately. Damage to your

tool or personal injury may result.

This jig saw is equipped with four cutting actions,

three orbital and one straight. Orbital action has a

more aggressive blade motion and is designed for

cutting in soft materials like wood or plastic. Orbital

action provides a faster cut, but with a less smooth

cut across the material. In orbital action, the blade

moves forward during the cutting stroke in addition to the up and down motion.

NOTE: Metal or hardwoods should never be cut in orbital action.

To adjust the cutting action:

- Move the cutting action lever (9) between the four cutting positions: 0, 1, 2, and 3.

- Position 0 is straight cutting.

- Positions 1, 2, and 3 are orbital cutting.

- The aggressiveness of the cut increases as the lever is adjusted from one to three, with

three being the most aggressive cut.

LED LIGHT

The jig saw is equipped with a light which projects on the cutting path.

- The light will come on when the trigger switch is depressed and will go off when the

trigger switch is released.

REMOVABLE SHOE SLEEVE (FIGURE F)

The non-marring shoe sleeve (5) should be used

when cutting surfaces that scratch easily, such as

laminate, veneer, or paint. It can also be used to

protect the shoe surface during transportation and

storage.

To attach shoe sleeve, place the front of the shoe

(6) into the front of the shoe sleeve (5) and lower the

jig saw as shown in figure F. The shoe sleeve will

click securely onto the rear of the shoe.

To remove shoe sleeve, grasp the sleeve from the

bottom at the two rear tabs and pull down and away

from the shoe.

Hints for optimum use

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may occur on the surface

closest to the shoe plate.

- Use a fine-tooth saw blade.

- Saw from the back surface of the workpiece.

- To minimize splintering, clamp a piece of scrap wood or hardboard to both sides of the

workpiece and saw through this sandwich.

Sawing metal

- Be aware that sawing metal takes much more time than sawing wood.

- Use a saw blade suitable for sawing metal.

- When cutting thin metal, clamp a piece of scrap wood to the back surface of the

workpiece and cut through this sandwich.

- Spread a film of oil along the intended line of cut for easier operation and longer blade

life. For cutting aluminum, kerosene is preferred.

RIP / CIRCLE CUTTING (FIGURE G, H)

Ripping and circle cutting without a pencil line are easily done with the rip fence / circle

guide (not included - available at extra cost).

Using the screw supplied with the accessory guide, position as shown in figure G and

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 7

thread the screw into the shoe to clamp the fence

securely.

When ripping, position as shown in figure G and slide

the rip fence under the screw from either side of the

saw. Set the cross bar (10) at desired distance from

blade and tighten screw. For ripping, the cross bar

should be down and against the straight edge of the

workpiece as shown.

When circle cutting, adjust rip fence so that distance

from blade to hole in fence arm (11) is at the desired

radius and tighten screw. Place saw so that hole in

fence arm is over center of circle to be cut (drill hole

for blade or cut inward from edge of material to get

blade into position). When saw is properly positioned,

drive a small nail through hole in fence arm. Using rip

fence as a pivot arm, begin cutting circle. For circle

cutting, the cross bar should be up, as shown in

figure H.

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Cord not plugged in. • Plug tool into a working outlet.

• Circuit fuse is blown. • Replace circuit fuse. (If the

product repeatedly causes the

circuit fuse to blow, discontinue

use immediately and have it

serviced at a Porter Cable

service center or authorized

servicer.)

• Circuit breaker is tripped. • Reset circuit breaker. (If the

product repeatedly causes the

circuit breaker to trip,

discontinue use immediately

and have it serviced at a Porter

Cable service center or

authorized servicer.)

• Cord or switch is damaged. • Have cord or switch replaced

at a Porter Cable Service

Center or Authorized Servicer

For assistance with your product, visit our website at www.portercable.com for a list of service

centers, or call the Porter-Cable Customer Care Center at (888) 848-5175

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 8

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the

tool; never immerse any part of the tool into a liquid.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our service website at

www.portercable.com. You can also order parts from your nearest Porter-Cable Factory Service

Center or Porter-Cable Authorized Warranty Service Center. Or, you can call our Customer Care

Center at (888) 848-5175.

SERVICE AND REPAIRS

All quality tools will eventually require servicing and/or replacement of parts. For information about

Porter-Cable, its factory service centers or authorized warranty service centers, visit our website at

www.portercable.com or call our Customer Care Center at (888) 848-5175. All repairs made by our

service centers are fully guaranteed against defective material and workmanship. We cannot

guarantee repairs made or attempted by others.

You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson,

Tennessee 38305, (888) 848-5175 - Attention: Product Service. Be sure to include all of the

information shown on the nameplate of your tool (model number, type, serial number, etc.).

ACCESSORIES

Since accessories, other than those offered by Porter-Cable, have not

been tested with this product, use of such accessories with this tool could be

hazardous. To reduce the risk of injury, only Porter-Cable recommended accessories

should be used with this product.

A complete line of accessories is available from your Porter-Cable Factory Service

Center or a Porter-Cable Authorized Warranty Service Center. Please visit our Web Site

www.portercable.com for a catalog or for the name of your nearest supplier.

THREE YEAR LIMITED WARRANTY

PORTER-CABLE will repair or replace, without charge, any defects due to faulty

materials or workmanship for three years from the date of purchase for tools (two years

for batteries). This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair information, visit

www.portercable.com or call (888) 848-5175. This warranty does not apply to

accessories or damage caused where repairs have been made or attempted by others.

This warranty gives you specific legal rights and you may have other rights which vary

in certain states or provinces.

In addition to the warranty, PORTER-CABLE tools are covered by our:

1 YEAR FREE SERVICE: PORTER-CABLE will maintain the tool and replace worn

parts caused by normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE: If you are not completely satisfied with the

performance of your PORTER-CABLE Power Tool for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For

products sold in Latin America, see country specific warranty information contained in

the packaging, call the local company or see website for warranty information.

To register your tool for warranty service visit our website at www.portercable.com.

WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call (888) 848-5175 for a free

replacement.

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 9

The following are PORTER-CABLE trademarks for one or more power tools and accessories: a

gray and black color scheme; a “four point star” design; and three contrasting/outlined longitudinal

stripes. The following are also trademarks for one or more Porter-Cable and Delta products: 2 BY

4®, 890™, Air America®, AIRBOSS™, Auto-Set®, B.O.S.S.®, Bammer®, Biesemeyer®, Builders

Saw®, Charge Air®, Charge Air Pro®, CONTRACTOR SUPERDUTY®, Contractor's Saw®,

Delta®, DELTA®, Delta Industrial®, DELTA MACHINERY & DESIGN™, Delta Shopmaster and

Design®, Delta X5®, Deltacraft®, DELTAGRAM®, Do It. Feel It.®, DUAL LASERLOC AND

DESIGN®, EASY AIR®, EASY AIR TO GO™, ENDURADIAMOND®, Ex-Cell®, Front Bevel

Lock®, Get Yours While the Sun Shines®, Grip to Fit®, GRIPVAC™, GTF®, HICKORY

WOODWORKING®, Homecraft®, HP FRAMER HIGH PRESSURE®, IMPACT SERIES™,

Innovation That Works®, Jet-Lock®, Job Boss®, Kickstand®, LASERLOC®, LONG-LASTING

WORK LIFE®, MAX FORCE™, MAX LIFE®, Micro-Set®, Midi-Lathe®, Monsoon®, MONSTER-

CARBIDE™, Network®, OLDHAM®, Omnijig®, PC EDGE®, Performance Crew™, Performance

Gear®, Pocket Cutter®, Porta-Band®, Porta-Plane®, Porter Cable®, Porter-Cable Professional

Power Tools®, Powerback®, POZI-STOP™, Pressure Wave®, PRO 4000®, Proair®, Quicksand

and Design®, Quickset II®, QUIET DRIVE TECHNOLOGY™, QUIET DRIVE TECHNOLOGY

AND DESIGN™, Quik-Change®, QUIK-TILT®, RAPID-RELEASE™, RAZOR®, Redefining

Performance®, Riptide®, Safe Guard II®, Sand Trap and Design®, Sanding Center®, Saw Boss®,

Shop Boss®, Sidekick®, Site Boss®, Speed-Bloc®, Speedmatic®, Stair Ease®, Steel Driver

Series®, SUPERDUTY®, T4 & DESIGN®, THE AMERICAN WOODSHOP®, THE

PROFESSIONAL EDGE®, Thin-Line®, Tiger Saw®, TIGERCLAW®, TIGERCLAW AND

DESIGN®, Torq-Buster®, TRU-MATCH®, T-Square®, Twinlaser®, Unifence®, Uniguard®,

UNIRIP®, UNISAW®, UNITED STATES SAW®, Veri-Set®, Versa-Feeder®, VIPER®, VT™, VT

RAZOR™, Water Driver®, WATER VROOM®, Waveform®, Whisper Series®, X5®, YOUR

ACHIEVEMENT. OUR TOOLS.®

Trademarks noted with ® are registered in the United States Patent and Trademark Office and may

also be registered in other countries. Other trademarks may apply.

4825 Highway 45 North

Jackson, Tennessee 38305

(888) 848-5175

www.portercable.com

90546382 PC600JS Jig Saw 12/10/08 9:11 AM Page 10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Porter-Cable Elektrowerkzeuge Handbücher

Porter-Cable

Porter-Cable PCC510 Bedienungsanleitung

Porter-Cable

Porter-Cable PC250MT Bedienungsanleitung

Porter-Cable

Porter-Cable 891 Bedienungsanleitung

Porter-Cable

Porter-Cable SPEEDTRONIC 518 Bedienungsanleitung

Porter-Cable

Porter-Cable PC1500HGA Bedienungsanleitung

Porter-Cable

Porter-Cable 557 Bedienungsanleitung

Porter-Cable

Porter-Cable 643 Bedienungsanleitung

Porter-Cable

Porter-Cable PCCF930 Bedienungsanleitung

Porter-Cable

Porter-Cable 513 Bedienungsanleitung

Porter-Cable

Porter-Cable RN175A Bedienungsanleitung

Porter-Cable

Porter-Cable NS150A Bedienungsanleitung

Porter-Cable

Porter-Cable 697839-8810 Bedienungsanleitung

Porter-Cable

Porter-Cable 7557 Bedienungsanleitung

Porter-Cable

Porter-Cable Tru-Match 6921 Bedienungsanleitung

Porter-Cable

Porter-Cable 630 Bedienungsanleitung

Porter-Cable

Porter-Cable 7403 Bedienungsanleitung

Porter-Cable

Porter-Cable 6602 Bedienungsanleitung

Porter-Cable

Porter-Cable PCE210 Bedienungsanleitung

Porter-Cable

Porter-Cable NS150C Bedienungsanleitung

Porter-Cable

Porter-Cable PC160JT Bedienungsanleitung

Porter-Cable

Porter-Cable PCC710 Bedienungsanleitung

Porter-Cable

Porter-Cable 7403 Bedienungsanleitung

Porter-Cable

Porter-Cable 557 Bedienungsanleitung

Porter-Cable

Porter-Cable PCE345 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch