POSIFLEX DG2000 Bedienungsanleitung
RF Dongle Installation Guide 1
INSTALLATION GUIDE FOR DONGLE
DG2000 FOR WIRELESS PRINTER
Rev. Original
KIT MODEL NUMBER: DG2000
KIT APPLICATION: This kit can be used to provide the wireless connection to a
Posiflex wireless POS printer like PP7700 series from the host Posiflex POS system.
KIT FUNCTION: With this kit connected as in the drawing Fig. 1 below, this kit
provides the convenience of wireless connection and maximum easiness for
software because this connection requires no WLAN and printer server concept as
most competitors can do. This wireless connection can be straight forwardly
considered as if the printer is directly connected to the COM port. However, please
note that such convenience is only available with Posiflex POS systems.
Fig-1 Setup and operation concept of the Dongle
INSTALLATION
1. COM port setting: Please first select a COM port in a Posiflex POS system for
the Dongle connection and set + 5 V DC support of this COM port by a
qualified technician under technical guidance from Posiflex Inc. Please reset the
power supply if later the Dongle is to be removed.
2. Dongle installation: Connect the 9 pin connector of the
Dongle to the COM port and find a place free from any
strong RF interference and metal object for setting up
the Dongle and/or the POS system. Use the double side
self adhesive tape to help holding the Dongle in place or
clip the Dongle at one of the top corners on rear of a Jiva
series POS system as in the picture to the right.
The whole Jiva series can access the Posiflex wireless thermal printer PP7700.To
do this, a wireless Dongle DG2000 for this printer must be separately purchased and
installed to one of the serial COM ports in Jiva system. Please enable the + 5 V DC
POSIFLEX
POS system
(PB, PST or TP)
COM port
DG2000
PP7700
P/N:19080900010
RF Dongle Installation Guide 2
power support for this COM port. Notice 2 hooks on rear side of the Dongle and
also 2 hooks on either top corner on rear side of main unit of the Jiva system. Match
the hooks to mount the Dongle to either corner of the Jiva system.
3. Wireless connection: Use the CDROM delivered with the wireless printer or
download from our web http://www.posiflex.com.tw and install the wireless
driver as described in the User’s Manual for the wireless printer.
SPECIFICATION
Input power : 5 V DC (combined in RS232 interface)
Operating current : 150 mA peak
Connector type : sub D 9 pin Female
RS232 protocol : 19200 bps, none parity, 8 data bits, 1 stop bit (38400 bps option)
Radio Frequency range : 2.4 ~ 2.4835 GHz
RF transmission range : 100 meters in free space
Dimensions: 69.84 mm x 39.95 mm x 25.8 mm (case)
cable length to system : 60 cm
Hooks On Rear Side Of Dongle
Hooks On Rear Side Of Jiva
Dongle Hooked On Rear Top
Corner Of Jiva System
Inhaltsverzeichnis
Andere POSIFLEX Computerhardware Handbücher
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
