POSIFLEX TM-30 Series Bedienungsanleitung

Package Contents

9.7” LM/TM-3X10E or 14” LM/TM-3X14E or

15” LM/TM-3X15E

POS Monitor……………...……….(x 1)

VGA Cable………………………..(x 1)

USB type A to B cable…………....(x 1)

(For TM-30XXE/32XXE Only)

Mounting kits …...……………..…(x 1)

User Manual………………………(x 1)

Specifications

LM-30XXE/32XXE Models

LM-3010E

LM-3014E

LM-3015E

LM-3210E

LM-3215E

Display

LCD Panel

9.7" TFT

LCD

14" TFT

LCD

15.0" TFT

LCD

9.7" TFT

LCD

15.0" TFT

LCD

Resolution

(H) x (V)

1024 x 768

1366 x 768

1024 x 768

Touch

Touch type

N/A

Interface

N/A

General Specification

Display

Interface

VGA

Power

Supply

12V from Posiflex terminal VGA port

TM-30XXE/32XXE Models

TM-3010E

TM-3014E

TM-3015E

TM-3215E

Display

LCD Panel

9.7" TFT LCD

14" TFT LCD

15.0" TFT LCD

Resolution

(H) x (V)

1024 x 768

1366 x 768

1024 x 768

Touch

Touch type

Bezel-free P-CAP touch panel

Resistive touch

panel

Interface

USB

General Specification

Display

Interface

VGA

Power

Supply

12V from Posiflex terminal VGA port

19610903010 Ver. Original

http://www.posiflex.com

LM/TM-30XXE/32XXE Monitor

User Manual

Views of LM/TM-3X10E

Front View

Rear View

I/O Ports of LM-3X10E

I/O Ports of TM-3010E

9.7” LM-3210E LCD Panel

VGA Port

DC-IN Power Jack

Power LED Indicator

9.7” LM-3010E LCD Panel

9.7” TM-3010E P-Cap Touch Panel

VGA Port

USB (Type B) Port

DC-IN Power Jack

Power LED Indicator

Mounting Bracket

for HS series Terminals

Mounting Bracket

for KS series Terminals

Mounting Bracket

for XT series Terminals

OSD button

EXT button

＋button

－button/ Power button

OSD Control Button

Views of the LM/TM-3014E

Front View

Rear View

I/O Ports

Side Mount Cover

14” LM-3014E LCD Panel

14” TM-3014E P-Cap Touch Panel

VGA Port

USB (Type B) Port

DC-IN Power Jack

USB Port

Power LED Indicator

Mounting Bracket

for KS series Terminals

Mounting Bracket

for XT series Terminals

OSD button

EXT button

＋button

－button/ Power button

OSD Control Button

Views of the LM/TM-3015E/3215E

Front View

Rear View

I/O Ports

15” LM-3215E LCD Panel

15” TM-3215E Resistive Touch Panel

15” LM-3015E LCD Panel

15” TM-3015E P-Cap Touch Panel

VGA Port

USB (Type B) Port

DC-IN Power Jack

LED Indicator

USB Port

Side Mount Cover

Mounting Bracket

for KS series Terminals

Mounting Bracket for

XT series Terminals

OSD button

EXT button

＋button

－button/ Power button

OSD Control Button

Installing LM/TM-30XXE/32XXE

According to the model type of your monitor and terminal, the relevant

instructions are provided below to help you mount your monitors onto your

Posiflex terminals. During installation, please ensure the terminal is properly

turned off and disconnected from the power sources to avoid potential hazards.

Mounting to HS series Terminals

1. Lay your POS terminal on a flat surface with

its rear facing towards you.

2. Press down the release tab of top I/O interface

cover.

3. Pull the top I/O cover in the direction shown

by the arrow in the figure to remove the cover.

4. Position the monitor on a flat surface. While

keeping it steady with one hands, pull the rear

mounting bracket upright as shown in the

figure.

5. Support your monitor to align its mounting

bracket with four screw holes at the back of

your terminal. Secure the mounting bracket

with four #6-32-10L fixing screws.

6. Connect the monitor to the terminal using VGA cable.

6.1 Connect one end of the VGA cable to

the VGA port at the bottom I/O plate

of your monitor.

6.2 Take the other end of VGA cable to

insert it into the VGA port of your

terminal.

7. For TM series users, connect the monitor to the terminal using USB

type A to B cable to enable touch function for your monitor. If the

monitor you are using isn’t TM series, please skip this step.

7.1 Grab Type-B connector of USB

cable, and then insert it into Type-B

USB port of your monitor

7.2 Properly attach Type-A connector of

USB cable to your POS terminal.

8. Break the release tab of the top I/O interface

cover for HS series terminal.

9. After tucking the extra cable into the I/O

compartment and thread the cable through the

cable exit, push the back cover into place.

10. After ensuring the monitor is well installed, tilt

your monitor up or down to your desired angle.

While setting up the tilting adjustment, be

careful not to press on the LCD panel.

Cable Exit

Mounting to KS Terminals

1. Position your terminal with its rear facing

towards you.

2. Take L type mounting bracket out of the

package. Align the four screw holes of the

mounting bracket with the hole pattern at the

back of the terminal.

3. Insert four #6-32-12L fixing screws into the

screw holes and then tighten the screws to

secure the mounting bracket.

4. Lay the monitor on a flat surface with the

screen facing downward and its I/O ports

facing toward you. While holding the monitor

steady with one hand, pull the monitor bracket

upright.

5. Lift the monitor to align three screw holes on

the monitor bracket with those on the bracket

attached to the terminal using the alignment

dots.

6. Properly attach two brackets with three #6-32-

6L fixing screws. Make sure the monitor is

well mounted onto your terminal.

Alignment Dot

7. Pull outward the locking levers and then

remove the neck cover in the direction shown

by the arrow.

8. Connect VGA cable to the terminal.

9. For TM series users, attach Type-A connector

of USB cable to your POS terminal.If the

monitor you are using isn’t TM series,

please skip this step.

10. Pass the cables through the cable exit, route them along the cable

passage, and fasten the cables with cable tie as shown in the picture.

11. Push back the neck cover into place.

12. Make sure the cables can be pulled out of the

cable exit from the base.

13. Connect VGA cable to your monitor.

Cable exit

Cable tie

14. For TM series users, grab Type-B connector of

USB cable, and then insert it into Type-B USB

port of your monitor to enable touch function.

If the monitor you are using isn’t TM series,

please skip this step.

15. The installation is completed. While tilting the

screen up or down in the direction shown by

the arrow, do not press on the LCD panel.

Mounting to XT Terminals with Gen 7E/8E Base

1. Position your terminal with its rear facing

toward you. At the edges of the base stand

bracket are located two shorter horizontal rails

(2) (3) and two longer vertical rails (1) (4),

which are used to hold your cable into place.

2. Release the rail from the base.

To run the cable through the cable passage on the left, according to

the sequence number, first remove the longer rail and then the shorter

one from the base stand by sliding them in the direction shown by the

arrow.

Or, if you prefer to thread the cable through the cable passage on the

right side, first remove the longer rail and then shorter one from the

base stand according to the sequence number.

3. After positioning your terminal with its screen

facing downwards, lift the monitor and then

align the four fixing screw holes on its

mounting bracket with the hole pattern at the

rear of the terminal as shown in the figure.

4. Insert four #6-32-10L screws into the screws

holes and then tighten them to secure the

mounting bracket.

5. Take the VGA cable out of the package, and

then connect it to your monitor.

6. For TM series users, plug Type-B connector of

USB cable into Type-B USB port of your

monitor to enable touch function. If the

monitor you are using isn’t TM series,

please skip this step.

7. While pushing the VGA cable into cable passages on the left side, also

reserve the enough cable for tilting the monitor.

8. For TM series users, tuck USB cable through the cable passage on the

right side. Reserve the enough cable needed for tilting the monitor.

Please skip this step if USB cable is not available.

Cable Exit

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere POSIFLEX Monitor Handbücher

POSIFLEX

POSIFLEX LM6112 Bedienungsanleitung

POSIFLEX

POSIFLEX PD-6807U Bedienungsanleitung

POSIFLEX

POSIFLEX LM-2010 Bedienungsanleitung

POSIFLEX

POSIFLEX PD-2500 Series Bedienungsanleitung

POSIFLEX

POSIFLEX TM4000 Series Bedienungsanleitung

POSIFLEX

POSIFLEX LM-7112 Bedienungsanleitung

POSIFLEX

POSIFLEX PD-300 Series Bedienungsanleitung

POSIFLEX

POSIFLEX LM-3315 Series Bedienungsanleitung

POSIFLEX

POSIFLEX LM-6207 Bedienungsanleitung

POSIFLEX

POSIFLEX TM-3112HDMI Bedienungsanleitung

POSIFLEX

POSIFLEX LM4115 Bedienungsanleitung

POSIFLEX

POSIFLEX LM6112 Bedienungsanleitung

POSIFLEX

POSIFLEX LM-2310 Bedienungsanleitung

POSIFLEX

POSIFLEX LM-2010 Bedienungsanleitung

POSIFLEX

POSIFLEX PD-2601 Series Bedienungsanleitung

POSIFLEX

POSIFLEX LM-7117 Bedienungsanleitung

POSIFLEX

POSIFLEX LM-31 E Series Bedienungsanleitung

POSIFLEX

POSIFLEX PD-30 UE Series Bedienungsanleitung

POSIFLEX

POSIFLEX LM-6801E Bedienungsanleitung

POSIFLEX

POSIFLEX LM-4015 Bedienungsanleitung

POSIFLEX

POSIFLEX LM-2010 Bedienungsanleitung

POSIFLEX

POSIFLEX LM-3010F/HS Bedienungsanleitung

POSIFLEX

POSIFLEX LM-4011U Bedienungsanleitung

POSIFLEX

POSIFLEX LM-4010DP Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung