Potterton Performa 24 Eco HE Bedienungsanleitung

bar

Reset Burner On

Flame Failure

Power On

User’s Guide Performa

24 Eco HE

This is a Wall Mounted Powered Flue Condensing Combination Boiler Gas Fired Central Heating Unit.

The boiler meets the requirements of Statutory Instrument “ The Boiler (Efficiency) Regulations 1993 No3083” and is

deemed to meet the requirements of Directive 92/42/EEC on the energy efficiency requirements for new hot water

boilers fired with liquid or gaseous fuels:-

Type test for purpose of Regulation 5 certified by:

Notified Body 0051.

Product/Production certified by:

Notified Body 0051.

For use in GB/IE only.

the nation’s favourite for

PLUMBING & HEATING SUPPLIES

SECURE PAYMENTS

shop online with confidence

FREE SHIPPING

on all orders over £100 to mainland UK

FINANCE AVAILABLE

spread the cost with low interest rates

PRICE MATCH

always get the best deals available

Boilers

Radiators

Heating controls



Cylinders

Fires

Renewable energy

Bathroom suites

Kitchen sinks & taps

Showers

Wet rooms

Towel warmers

Bathroom furniture

& much more

HUGE REDUCTIONS

we have

ON THOUSANDS OF ITEMS

0844 800 3460

CALL US ON

visit our website

plumbnation.co.uk

2Publication No. 5111812

Natural Gas

Potterton Performa 24 Eco HE

G.C.No47 393 11

Where fitted, user label for

optional timer to be applied here.

IMPORTANT - Installation, Commissioning, Service & Repair

This appliance must be installed in accordance with the

manufacturer’s instructions and the regulations in force. Read

the instructions fully before installing or using the appliance.

In GB, this must be carried out by a competent person as

stated in the Gas Safety (Installation & Use) Regulations.

Definition of competence: A person who works for a CORGI

registered company and holding current certificates in the

relevant ACS modules, is deemed competent.

In IE, this must be carried out by a competent person as

stated in I.S. 813 “Domestic Gas Installations”.

Lifting - This product should be lifted and handled by two

people. Stooping should be avoided and protective equipment

worn where necessary. Carrying & lifting equipment should be

used as required, e.g. when installing in a loft space.

The addition of anything that may interfere with the normal

operation of the appliance without express written permission

from the manufacturer or his agent could invalidate the

appliance warranty. In GB this could also infringe the Gas

Safety (Installation and Use) Regulations.

Warning - Check the information on the data plate is

compatible with local supply conditions.

Benchmark Commissioning Checklist

Please ensure that your installer hands you the boiler

Installation & Service Instructions with the Benchmark

Commissioning Checklist sections completed. The details in

the Checklist will be required in the event of any warranty

work. Keep the instructions in a safe place and ensure that the

Service Interval Record at the back is completed at each

service visit.

CORGI

All CORGI registered installers carry a CORGI identification

card and have a registration number. You can check your

installer is registered by telephoning 0870 4012300 or writing

to:-

1 Elmwood,

Chineham Business Park,

Crockford Lane,

Basingstoke. RG24 8WG

or check online at www.corgi-gas-safety.com

This product has an energy rating (B) on a scale of A to G.

For more information see www.boilers.org.uk. This is a certification mark.

Publication No. 5111812

In an Emergency

If a water or gas leak occurs or is suspected, the boiler

can be isolated at the inlet valves as follows;

1. Turn off the electrical supply and turn the selector

switch on the facia box to the OFF position.

2. Using a suitable open ended spanner or screwdriver

turn the square on the gas tap to the left to isolate the

gas supply at the boiler (Fig. 1).

3. The isolating valves are positioned under the boiler

and can be closed by turning their taps to the right

towards the wall (Fig. 2).

4. Call your Installer or Service Engineer as soon as

possible.

In case of gas leaks

1. If a gas leak is found or suspected, turn off the gas

supply at the meter immediately and at the isolating

valve on the boiler if possible. Contact your Gas

Supplier immediately.

Servicing your Appliance

1. For reasons of safety and economy your appliance

should be serviced annually. Servicing must be

performed by a competent person. Your Installer or

Service Engineer will be able to advise you.

2. Any purpose provided ventilation should be checked

periodically to ensure that it is free from obstruction.

Electricity Supply

1. THIS APPLIANCE MUST BE EARTHED.

2. A standard 230V ~ 50Hz supply is required. The

appliance must be protected by a 3 amp fuse.

Never Hang Flammable Items Over The Appliance

Gas Tap

Heating Flow, Heating

Return and Mains

Water Inlet

Isolating Valves

Fig. 1

Fig. 2

4Publication No. 5111812

Introduction

1. Your Potterton Performa 24 Eco HE is a gas fired,

room sealed, powered flue condensing combination

boiler, providing central heating for your home and

mains fed domestic hot water to taps and shower. It

is fully automatic and does not have a pilot light.

2. Priority is given to the hot water mode - when a hot

water tap is turned on the supply of heat to the

central heating circuit is interrupted.

3. Due to the high efficiency and resultant low flue

gas temperature when in condensing mode a white

plume of condensate will be emitted from the

terminal. This will be particularly evident during

periods of low outside temperature.

Operating the Boiler

1. Ensure that the electricity and gas supplies are

turned on. Check that the central heating pressure is

between 0.5 and 1.0 bar (Fig. 3).

2. Turn the On/Off/Reset selector switch either anti-

clockwise from the off position (Fig. 5) to both central

heating and domestic hot water or clockwise to

domestic hot water only.

3. In either position the green “power”neon ( ) will

illuminate (Fig. 4).

4. Position (i) In this position the central heating will

operate according to demand or provide domestic hot

water when a tap or shower is turned on (Fig. 6).

Priority is given to domestic hot water.

5. Position (ii) In this position hot water will be

provided when a tap or shower is turned on (Fig. 7).

6. The boiler will light automatically on demand.

7. The orange “burner”neon ( ) will illuminate

when the boiler is operating and the main burner is

on (Fig. 4).

IMPORTANT: When the selector switch is in the

‘0’ (Off) position the electrical supply to the boiler

is isolated. The boiler will not operate and the

integral timer (if fitted) will require resetting once

the selector switch is set to either Position (i) or

Position (ii).

bar

Reset Burner On

Flame Failure

Power On

Performa 24 Eco HE

Reset

Position (ii)

(Hot Water)

Fig. 6

Fig. 7

Reset

OFF Position

Fig. 5

Fig. 4

Fig. 3

1. On/Off/Reset Selector Switch

2. Burner On & Fault Indicator Neon

3. Power Neon

4. Flame Failure & Fault Indicator Neon

5. Central Heating Temperature Control

6. Hot Water Temperature Control

7. Central Heating System Pressure Gauge

8. Optional Integral Timer Position

12 34 5 6 7 8

bar

Position (i)

(Central Heating or Hot Water)

Publication No. 5111812

Fault Indication

1. Your Potterton Performa 24 Eco HE has three neon

indicators. The upper two function as boiler on and

fault indicators.

2. Depending on the nature of the fault the upper two

neons will illuminate, go off or flash.

3. There are five possible combinations, each

indicating one or more fault conditions. These are

described below.

The flue or flue terminal is blocked or obstructed in

some way, or there is an internal fault.

If there is no external blockage of the flue that can be

easily removed contact your Installer or Service

Engineer.

The circulating pump is faulty or the system pressure

has dropped. Check the system pressure (see page 7).

If the pressure is in the normal range a pump fault is

indicated. Contact your Installer or Service Engineer.

A fault on the boiler temperature sensor is indicated.

Contact your Installer or Service Engineer.

The primary system or the boiler has overheated.

Allow the boiler to cool. Turn the selector switch fully

anti-clockwise against the spring pressure to the

‘Reset’position and hold for at least 2 seconds.

If this occurs repeatedly contact your Installer or

Service Engineer.

If the boiler does not relight after resetting it is possible

that the flue has overheated. Contact your Installer or

Service Engineer.

The burner has failed to light, or incomplete lighting of

the burner has occurred. Turn the selector switch fully

anti-clockwise against the spring pressure to the

‘Reset’position and hold for at least 2 seconds.

If this occurs repeatedly contact your Installer or

Service Engineer.

If the boiler does not relight after resetting blockage of

the condensate drain or trap has occurred. Contact

your Installer or Service Engineer.

Burner On

Flame Failure

Power On

Off

Fast Flashing (2 every second)

Burner On

Flame Failure

Power On

Off

Slow Flashing (1 every 2 seconds)

Burner On

Flame Failure

Power On

Slow Flashing (1 every 2 seconds)

Burner On

Flame Failure

Power On

Slow Flashing (1 every 2 seconds)

Burner On

Flame Failure

Power On

Off

Reset

Reset Position

6Publication No. 5111812

Temperature Control

1. Central Heating: The central heating hot water

flow temperature can be adjusted between 30°C (±

5° C) minimum and 85°C (± 5°C) maximum.

2. Turn the control knob clockwise to increase the

temperature (Fig. 8).

3. In normal winter usage we recommend that the

central heating temperature be set at maximum.

4. Domestic Hot Water: The temperature of the

domestic hot water can be adjusted by turning the

control knob clockwise to increase up to a maximum

of 65°C (Fig. 9).

5. The temperature of the water is also dependent on

the water flow rate and the temperature of the mains

water coming into the house.

6. By slightly reducing the flow from the tap the

temperature will increase up to the maximum if

required.

7. The flow rate can be reduced down to as low as 2.5

litre/min. The boiler will still recognise the need to heat

the water.

Domestic Hot Water

Temperature Control

Fig. 8

Central Heating

Temperature Control

Fig. 9

Publication No. 5111812

Central Heating System Pressure

1. The water pressure in the central heating system

is indicated by the pressure gauge.

2. With the system cold and the boiler not operating

the pressure should be between 0.5 and 1.0 bar.

During operation the pressure should not exceed 2.5

bar, and will normally be between 1.0 and 2.0 (Figs.

10 & 11).

3. A pressure of 3 or greater indicates a fault. The

safety pressure relief valve will operate, at a pressure

of 3 (Fig. 12). It is important that your Installer or

Service Engineer is contacted as soon as

possible.

4. The minimum pressure for correct operation is 0.5.

If the pressure falls below 0.5, this may indicate a

leak on the central heating system (Fig. 13).

To Shut Off the Boiler

1. For short periods: Turn the selector switch to the

OFF position (Fig. 14).

2. For long periods: Turn off the selector switch

(Fig. 14), electricity and gas supplies.

If your home is to be left unoccupied for long

periods during cold weather the boiler and whole

system should be drained unless equipped with

frost protection.

3. Your installer will advise you about frost protection

and draining the system.

IMPORTANT: When the selector switch is in

the ‘0’ (Off) position the electrical supply to the

boiler is isolated. The boiler will not operate

and the integral timer (if fitted) will require

resetting once the selector switch is set to

either Position (i) or Position (ii).

bar

ON/OFF/RESET

Selector Switch

Reset

OFF Position

Fig. 14

Normal Pressure (when cold)

Normal Pressure (operating)

Fig. 10

Fault

Fig. 11

Below Minimum

Fig. 12

Fig. 13

Pressure Gauge

8Publication No. 5111812

Clearances around the Boiler

(Figs. 15 & 16)

1. The minimum clear spaces needed around the boiler

measured from the casing are as follows:

Top - 200mm

Bottom - 200mm

Left side - 5mm

Right Side - 20mm/5mm

Front - 5mm (In Operation)

- 450mm (For Servicing)

* NOTE: The boiler can be operated with a clearance

of 5mm at the right. This is also sufficient for routine

maintenance. However a clearance of 20mm is

required if it is necessary to remove the secondary

heat exchanger. This should be considered when

siting the appliance and in the event of any

subsequent alteration in the area of installation.

2. These areas must not be obstructed in any way.

Blocking the clearance spaces may result in the

boiler overheating and damage may occur.

3. The gas burning compartment of your boiler is

completely sealed from the room in which it is fitted.

Products from the combustion of gas are vented to the

outside through the flue terminal which must be kept

free from obstruction as this would interfere with the

correct operation of the boiler.

4. The boiler may be installed in a cupboard if these

minimum clearances are kept. The compartment should

be large enough to house the boiler and ancillary

equipment only.

5. IT SHOULD NOT BE USED AS A STORAGE

CUPBOARD.

Check List

1. If a fault develops, or is suspected, call your Installer

or Service Engineer as soon as possible.

2. Go through the following check list before you make

contact.

a) Is the electricity supply on ?

b) Is the selector switch on (giving a green “Power ON”

light) and set for both Central Heating and

Domestic Hot Water ?

c) Is the red “Flame Failure”indicator lit ? Turn the

On/Off/Reset selector fully anti-clockwise.

d) Is the gas supply on ?

e) Is the mains water supply turned on ?

f) Is the system pressure correct ?

g) Are the boiler temperature controls set high enough?

h) Is the time clock (if fitted) calling for central heating ?

i) Is the room thermostat (if fitted) set high enough ?

j) Are the radiator valves open ?

bar

Reset Burner On

Flame Failure

PowerOn

200mm Min

780mm

450mm

200mm Min

20mm/5mm Min

see *NOTE:

5mm Min

8mm Min

450mm Min

For Servicing

Purposes

Fig. 15

Fig. 16

In Operation

Publication No. 5111812

Cleaning the Outercase

The painted panels should be wiped with a damp

cloth and then dried completely. Do not use abrasive

cleaning agents.

Spare Parts

IMPORTANT - Only a competent person should be

used to service or repair this boiler.

1. Any repairs to the boiler will usually be the

responsibility of the Installer during the guarantee

period after which spare parts may be obtained

through approved Potterton stockists if required.

2. Quote the appliance name, model number and

where possible the part number when ordering

spares. A parts list is included in the Installation and

Servicing Instructions.

3. The name, model number, and serial number can

be found on a label on the inner face of the lower

right hand case panel (see back page).

Andere Handbücher für Performa 24 Eco HE

Inhaltsverzeichnis

Andere Potterton Kessel Handbücher

Potterton

Potterton SIRIUS THREE FS 130 Fehlerbehebungshandbuch

Potterton

Potterton Performa 30 HE Montage- und Wartungsanleitung

Potterton

Potterton Prorile Prima 30e Benutzerhandbuch

Potterton

Potterton Performa 30 HE Montage- und Wartungsanleitung

Potterton

Potterton Promax SL Range Bedienungsanleitung

Potterton

Potterton Kingfisher Mf CFL40 - 100 Montage- und Wartungsanleitung

Potterton

Potterton Paramount two Gebrauchsanweisung

Potterton

Potterton Heatmax Combi HE Range Bedienungsanleitung

Potterton

Potterton iHE 150 Versionshinweis

Potterton

Potterton Puma Flowsure+ Montage- und Wartungsanleitung

Potterton

Potterton Statesman System L Montage- und Wartungsanleitung

Potterton

Potterton Eurocondense three Betriebsanleitung

Potterton

Potterton Suprima 100 Montage- und Wartungsanleitung

Potterton

Potterton Diplomat HE Bedienungsanleitung

Potterton

Potterton Boiler Bedienungsanleitung

Potterton

Potterton Performa 28 Benutzerhandbuch

Potterton

Potterton Promax 24 Combi ErP Bedienungsanleitung

Potterton

Potterton Titanium 24 Montage- und Wartungsanleitung

Potterton

Potterton Gold HE A Range Montage- und Wartungsanleitung

Potterton

Potterton Suprima 80 HE Bedienungsanleitung

Potterton

Potterton LPG 50e Bedienungsanleitung

Potterton

Potterton Derwent Prestige plus Gebrauchsanweisung

Potterton

Potterton Gold H Range Bedienungsanleitung

Potterton

Potterton Promax System HE Betriebsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung

Radiant

Radiant R2K 55 Handbuch

Worcester

Worcester Greenstar 36LXi Bedienungsanleitung