Power Fist 9105131 Bedienungsanleitung
V1.0 9105131
Please read and understand all instructions before use. Retain this manual for
future reference.
This page is intentionally left blank.
SPECIFICATIONS
Voltage Rating 5V DC
Amperage Rating 1 Amp
Wattage 5 Watts
Lamp Type LED
Bulb Type LED
Lumens Rating 600 lm
Number of Lamps 1
Power Source 1,800 mAh Li-ion battery
Run Time 4 Hours
Rated Life 10,000 hours
Base Type Magnetic
Housing Material ABS
Output Modes High/Low/Top/O
Switch Type Dimmer
Colour/Finish Black/green
Dimensions (L x W x H) 8-5/16 x 1-7/8 x 1-5/16 in.
INTRODUCTION
Illuminate workspaces in the garage, shop or on the jobsite with this portable
LED worklight. Energy-ecient LEDs save money on power bills. The hinged
LED panel allows a range of angles for better illuminate of the workspace.
Dimmer Switch for easy operation. Lightweight yet durable aluminum housing.
SAFETY
WARNING! Read and understand all instructions before using this tool.
The operator must follow basic precautions to reduce the risk of
personal injury and/or damage to the equipment.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or death
if certain instructions are not followed.
DANGER! This notice indicates an immediate and specic hazard that will result in
severe personal injury or death if the proper precautions are not taken.
WARNING! This notice indicates a specic hazard or unsafe practice that could result in
a serious injury if the proper precautions are not taken.
V1.0 LED RECHARGEABLE WORK LIGHT 9105131
Page 3 www.princessauto.com / 1-800-665-8685
CAUTION! This notice indicates a potentially hazardous situation that may result in
minor or moderate injury if proper practices are not taken.
NOTICE! This notice indicates that a specic hazard or unsafe practice will result in
equipment or property damage, but not personal injury.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from
the work area.
3. Store unused tools properly in a dry, safe and secure location to prevent
rust, damage or misuse.
4. Do not install or use in the presence of ammable gases, dust or liquids.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the
Canadian Standards Association (CSA) or American National Standards
Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the inuence of drugs,
alcohol or medications.
2. Avoid unintentional starts. Make sure the dimmer switch is set to OFF
before connecting the work light to a power supply.
SPECIFIC SAFETY
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specic
function. Do not modify or alter this tool or use it for an unintended
purpose.
9105131 LED RECHARGEABLE WORK LIGHT V1.0
www.princessauto.com / 1-800-665-8685 Page 4
2. Do not stare into the light. The light may cause irritation and temporarily
impair your vision.
3. Do not overcharge battery (See Care & Maintenance).
BATTERY SAFETY
WARNING! Do not charge a damaged or frozen battery. Contact your
local municipality for proper disposal procedures.
Consult the Safety Data Sheet (SDS) for your battery before use or
maintenance.
1. Do not expose the battery to heat or throw it in a re. The contents are
ammable and the battery may explode. Remove any source of ignition
such as an open ame or a tool like a heater from the area.
2. Do not inhale smoke issuing from a burning battery, as it is toxic.
3. Do not disassemble or crush the battery as the contents are corrosive
and ammable. Exposure may cause an injury. There is a risk of escaping
hazardous vapors. These vapors can irritate the respiratory track. Always
ensure proper ventilation and immediately consult a doctor, if you feel
unwell.
4. Even a discharged battery may still carry a charge. To prevent a shock,
place battery terminal caps or covers over the terminal to prevent
accidental contact.
5. Leaking battery uid can cause irritation of the skin or burns. If contact
should occur, ush immediately with water. In case of accidental contact
with the eyes, seek medical aid.
6. Do not disconnect from the power source in place of using the ON/OFF
switch on the tool. This can lead to an accidental startup when the tool is
connected to the power supply.
7. Do not allow a rechargeable battery to fully discharge. This will damage
the battery. Recharge the battery as soon as possible.
8. Do not store the battery completely discharged. Charge it fully before
storing. Recharge occasionally if storing for a long time.
9. Discontinue using or charging a li-ion battery if it changes shape or is
abnormally hot. The battery may leak or ignite. Move the battery to a re
proof location and observe for 15 minutes. Safely dispose of the battery.
POWER TOOL PRECAUTIONS
1. Do not use any power tool with a malfunctioning power switch or control.
A power tool that fails to respond to the controls is dangerous and can
V1.0 LED RECHARGEABLE WORK LIGHT 9105131
Page 5 www.princessauto.com / 1-800-665-8685
cause an injury. A qualied technician must repair and verify the power
tool is operating correctly, before it can be used.
2. Shut the power o and disconnect the work light from the power supply
(if possible) before making any adjustments, cleaning, servicing or when
storing. Such preventive safety measures reduce the risk of starting the
tool accidentally.
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace
the missing part before operating. Failure to do so could result in a
malfunction and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
CONTENTS
Make sure that all items in the contents are included.
• Work Light
IDENTIFICATION KEY
A. Hinge
B. USB Port
C. Work Light Body
D. Locking Knob
E. Magnetic Base
F. Dimmer Switch
G. LED Panel
H. D-Ring
OPERATIONS
1. The battery is not fully charged out of the
carton. Charge the battery before rst use.
2. Position the work light in a location that will illuminate your workspace.
3. Place the work light on a at surface.
FIGURE 1.
9105131 LED RECHARGEABLE WORK LIGHT V1.0
www.princessauto.com / 1-800-665-8685 Page 6
4. Loosen the locking knob to change the work light body's angle to better
illuminate an area. Retighten the locking knob once the desired position is
chosen.
5. Adjust the LED panel on the hinge. It has a 180º range.
6. Turn the dimmer switch clockwise to turn the work light on. The light
intensity increases as you turn the knob. Turn counterclockwise to dim
the light and turn the work light o.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is ecient, easier to
control and will have fewer problems.
2. Inspect the tool components periodically. Repair or replace damaged or
worn components. Only use identical replacement parts when servicing.
3. Keep the tool handles or gripping surfaces clean and dry.
4. Maintain the tool’s labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualied service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
RECHARGING THE WORK LIGHT
1. Check the indicator lights to determine if you need to recharge the
battery.
• There are four small LEDs above the dimmer switch. Each represents
25% of the power level. When the power is down to 50 or 25%,
recharge the work light.
2. Lift the waterproof cover.
3. Insert the charging cable's USB-C plug into the USC-C port.
4. Plug the USB plug into a power supply's USB port.
5. The glowing LEDs will indicate the battery's charge level.
6. Battery is fully charged and overcharge function is active when all four
LEDs are illuminated.
7. Remove the charge cable and close the waterproof cover once the battery
is fully charged.
V1.0 LED RECHARGEABLE WORK LIGHT 9105131
Page 7 www.princessauto.com / 1-800-665-8685
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualied technician
service the tool.
9105131 LED RECHARGEABLE WORK LIGHT V1.0
www.princessauto.com / 1-800-665-8685 Page 8
V1,0 9105131
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.
Cette page a été laissée blanche intentionnellement.
Inhaltsverzeichnis
Sprachen:
Andere Power Fist Arbeitsleuchte Handbücher
Beliebte Arbeitsleuchte Handbücher anderer Marken
PowerSmith
PowerSmith PWLD080T Bedienungsanleitung
MaxLite
MaxLite 73683 Bedienungsanleitung
Heitronic
Heitronic Trend 27867 Bedienungsanleitung
Monzana
Monzana Gore MZCL10 Bedienungsanleitung
EINHELL
EINHELL TE-CL 18/2000 LiAC Bedienungsanleitung
Bayco
Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Bedienungsanleitung