2.5.
WARNING: MAKE SURE THE TOOLS IS TURNED OFF AND THE BATTERY IS REMOVED
BEFORE MAKING CHANGING BITS OR MAKING ANY ADJUSTMENTS TO THE TOOL
1.(SEE FIGURE 1)Turn the tool OFF and remove the battery.
2.Press and hold the spindle lock button (1)
3.Use the wrench supplied, rotate the collet nut (2) counter clock
wise to loosen the collet and remove the cutting bit.
Note: you will feel some resistance as the bits slides in the collet.
Select and insert the correct collet (1/8" or 1/4") for the size bit to
be installed. To change collet sizes the collet nut must be
completely removed, the old collet removed from the tool shaft
and the appropriate size collet inserted and the collet nut replaced.
Note: The collets are symmetrical and have no "UP" or "DOWN".
5. Insert the shank end of the selected bit through the opening in the
collet nut a minimum of 3/4" (19mm) into the collet.
6. Press and hold the spindle lock button.
7. Use the wrench, rotate the collet nut clock wise to tighten the collet and secure the cutting bit.
Note: Tighten firmly but do not over tighten.
12. DISCONNECT THE TOOL FROM THE POWER SUPPLY.
When not in use, prior to maintenance and during the tool change, e.g. saw blade, drill bit and
machine tools of all kinds disconnect from the power supply.
13. DO NOT LEAVE ANY TOOL KEYS INSERTED.
Before switching on, check that keys, adjustment or setting tools have been removed from the
power tool.
14. AVOID ANY UNINTENTIONAL OPERATION OR STARTING-UP OF THE DEVICE.
Do not place your finger on the switch when carrying tools connected to the power supply. Make
sure that the switch is off when connecting the device to the power supply.
15. POWER EXTENSION CABLES.
Use only those extension cables that have been manufactured for this purpose and are marked as
appropriately tested and approved.
16. BE ALERT.
Observe your work. Proceed sensibly. Do not use the tool if you are physically or mentally
impaired in any manner. Do not operate tools under the influence of drugs, alcohol or medication.
17. CHECK YOUR TOOL FOR DAMAGE.
Before using the tool, carefully check the protective devices for problem-free operation and
intended function. Verify there are no damaged parts. Check whether the function of moving parts
is in order, whether they stick and whether parts are damaged.
DAMAGED PROTECTIVE DEVICES AND PARTS MUST BE PROPERLY REPAIRED
OR REPLACED BY A CUSTOMER-SERVICE WORKSHOP PRIOR TO "TOOL USE".
NEVER USE TOOLS AND SWITCHES THAT CANNOT BE SWITCHED ON AND OFF.
18. REPAIRS ONLY BY AN ELECTRICAL SPECIALIST.
This power tool complies with all known safety regulations. Only an electrical specialist may carry
out repairs.
19. USE ONLY ACCESSORIES AND ADDITIONAL DEVICES RECOMMENDED BY THE
TOOL MANUFACTURER.
The use of any insert tools or accessories other than those recommended in the operating
instructions increase risk of injury.
INSTALLING BITS
1. Do not overload the tool. If the speed drops dramatically, decrease the pressure immediately.
2. Do not apply excessive pressure to the tool while cutting.
3. Always use sharp bits. If the bit becomes dull, stops abruptly or becomes blocked, turn off
immediately.
4. Use the power switch properly. Be aware the tool will continue to operate while the power switch is
ON. It must be switch manually to OFF to stop the motor.
5. Do not attempt to start the tool with the bit in contact with the material. Allow the motor to reach full
speed before engaging the work piece.
6. Never touch the bit, collet nut or any moving parts while the tool is in operation.
7. Hold the tool firmly during start-up and while cutting. Install and use the adjustable side handle to
improve you grip when needed. Maintain control of the tool at all times while the blade is rotating.
8. Wear safety glasses at all times when using this tool.
9. Do not touch the cutting bit immediately after use, it may be very hot.
10. Make sure the bit is properly installed and secure before using the tool.
11. Make sure the are to be cut is free of nails, staples or other debris that could damage the blade or
cause loss of tool control.
WARNING:This tool can cause serious injury if not used properly. Read this entire manual
before using. Before each use, verify that the tool bit is securely tightened
1.Select and install the proper cutting bit for the material you will
be cutting.
Note: The High Speed Steel spiral bits supplied with this tool are
suitable for wood, drywall, plastic, fiberglass and other soft
materials. They are not intended for use on metal, stone,
concrete, ceramic tile or other hard materials.
2.Mark the desired path of the blade and ensure that the area
around, above and below is clear of obstructions.
3.(SEE FIGURE 4) Start the tool by sliding the power switch (1) to
the on position and allow the tool to reach full speed.
4.Using both hands, carefully plunge the bit through the material
and maneuver the blade to the desired path. Move slowly and at
a steady rate of speed.
Note: Due to the rotation direction of the bit, a clockwise
"left-to-right" motion generally produces the best results.
5.After the completion of the cut, remove the tool and turn the power switch to the off position.
6.Maintain control of the tool until the bit has stopped turning.
SPECIAL WARNINGS WHEN USING THIS CUTOUT TOOL
USING THE CUTOUT TOOL
IF YOU HAVE ANY PROBLEMS OR QUESTIONS CONCERNING THIS PRODUCT,
DO NOT RETURN IT TO YOUR RETAILER. CONTACT CUSTOMER SERVICE AT
1-888-422-7800.
(FIGURE 3)
1
2
(FIGURE 4) 1
