Poweramp PowerHold Installationsanleitung

IO PH PR 12/13

For comprehensive installation instructions of the PowerHold

read and understand the Installation and Operation Manual.

PowerHold Installation Overview

POWERPACK LOCATION OPTIONS

POWERHOLD REMOTE MOUNT POWERPACK

Inside Building (Remote Mount)

Locate powerpack to minimize

obstruction potential. Hydraulic and

electrical lines from the powerpack

to the restraint are best placed

through min. 3” PVC (hydraulic)

and 3/4” (electrical) chase during pit

construction.

Under The Dock Leveler

When combined with hydraulic leveler pump or

remotely mounting under leveler, make certain

to locate the powerpack where leveler will not

interfere in below dock conditions. The routing

of hydraulic and electrical lines from the

powerpack to the restraint are best placed

through min. 3” PVC (hydraulic) and 3/4”

conduit (electrical)

chase during pit

construction.

Allow

Enough

Clearance

for Possible

Seal or

Shelter

Dock Face (Self Contained)

Appropriate location when the likelihood of

flooding, snow removal and damage from

trailer/trucks is minimal. Also recommended

for use with non-hydraulically powered dock

levelers.

Coordinate powerpack location and hose

length for proper placement.

Poweramp • Division of Systems, LLC • W194 N11481 McCormick Dr. • Germantown, WI 53022

800.643.5424 • fax: 262.255.4199 • www.LoadingDockSystems.com

For comprehensive installation instructions read and understand the

Installation and Operation Manual.

PowerHold Installation Overview

A continuing product improvement process is in effect at Systems, LLC. We reserve the right to make product changes without prior notice.

Concrete Dock Face (Standard installation)

Driveway Mount (Recommended when dock face is unsuitable for PowerHold Mounting)

Cantilevered Dock (For bumper projection >4” or cantilevered dock or Edge-of-Dock leveler)

48”

8” Min.

Driveway mount requires attachment to

a concrete drive greater than 8” thick.

For asphalt drive, pour 48”x48”x8”

(min.) concrete pad and include six (6)

3/4” dowels into foundation wall. Then

proceed with adhesive anchors or weld

plate embed.

Determine offset

then proceed with

“Driveway Mount”

instructions below.

20”

Weld three sides of PowerHold back plate to the

optional embed mounting plate (Part #7953-0119)

with continuous 1/4” fillet weld.

5 1/4” minimum

To determine size offset required, take total effective

bumper projection (bumper size plus any cantilever) and

subtract 4”.

48”

8” Min.

Using back plate as a guide, drill six (6) holes

for wedge anchors (3/4”x 5 1/4” min.) (Kit

#2103-0003)

Wedge Anchors Method Drive Embed Method

Wedge Anchors Method Weld Plate Embed Method

36”

14”

Embed

Plate

located 2”

above grade 3/8”

Driveway Mount Wall Mount

Dim. A

Offset Formula

Dim. A Dim. B Offset

Bumper Projection Cantelever

4" + Dim B

6" + Dim B -4" = Offset

10" + Dim B

15" + Dim B

Dim. B

Dim. A

Dim. B

Weld method

Properly locate and level the drive embed weld

plate (Part#7953-0132) in the drive approach.

Observe Cantilever conditions for proper

positioning. Weld restraint to embed plate with a

continuous ¼” filet weld.

(Kit #2103-0003)

Install six (6) 3/4” Dia. x 5 1/4”

min. wedge anchors at the base

of the PowerHold.

Dim. B

48”

For filler requirements from 1 ½”to

7 ½” use cantilever bracket #9414-

0054

weld to

embedded mounting plate (Part

#7953-0119)

For filler requirements for 8 3/4” to

13 3/4” use cantilever bracket

#9414-0055 and anchor cantilever

bracket to the dock face (3/4” Dia.

X 5 1/4” min.) (Kit #2103-0003) or

weld to embedded mounting

Plate (Part #7953-0119).

and anchor cantilever bracket

to the dock face or

Andere Poweramp Hebesystem Handbücher

Poweramp

Poweramp LMP Series Bedienungsanleitung

Poweramp

Poweramp PowerHook Installationsanleitung

Poweramp

Poweramp Bar Lift Bedienungsanleitung

Poweramp

Poweramp RCR Series Bedienungsanleitung

Poweramp

Poweramp PowerLift Bedienungsanleitung

Poweramp

Poweramp LHP Series Bedienungsanleitung

Poweramp

Poweramp EH Series Bedienungsanleitung

Poweramp

Poweramp CentraAir Bedienungsanleitung

Poweramp

Poweramp CM Series Bedienungsanleitung

Poweramp

Poweramp CentraAir Bedienungsanleitung

Poweramp

Poweramp PR Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung