PowerFleet Vista Bedienungsanleitung
PowerFleet V-AI12
Quick Installation Guide
Thank you!
We are excited to introduce you to your new V-AI12 Connected Dashcam.
With Vista you can harness the power of video to connect your fleet vehicles, help protect your drivers on the
road and save lives.
Have a safe trip,
Vista team
Explore Vista
• CAPTURE THE DRIVE - Simultaneously capture the road and cabin to detect distracted driving and risky
driving events.
• LIVE VIDEO - View live video from your camera using any device.
• AI DRIVER ALERTS - Provide visual and audio alerts of distracted and risky driving events.
• CLOUD MANAGEMENT - Instant access to view and download live video, events, and recordings. *
*_Subject to available cellular network coverage.
What’s in the box
V-AI12 features
ROAD-FACING CAMERA
Install V-AI12
Before you start, make sure that the vehicle is parked on a level surface and that the windshield is clean and
dry.
• Unscrew the safety screws that lock the tamper proof case using the specialty screwdriver.
• Insert the SIM and SD cards.
• Attach the mounting bracket onto the camera.
• Place the camera as high as possible on the driver side of the vehicle.
• Remove the 3M adhesive tape cover, and mount the camera to the windshield.
WARNING: Prior to installation, please review safety warnings and guidelines at powerfleet.com/disclaimers
Hardwire to the vehicle fuse box
Hardwiring a dashcam to the vehicle’s fuse box is one of the most common installation methods to power on
your dashcam. In order to utilize the V-AI12 full features such as active standby, the camera must be
connected to a constant 12V power source.
NOTE: The hardwiring kit includes 2 wires; one RED wire that connects to a constant 12V source and a BLK
ground wire that will go to a metal ground bolt.
Essential Install Package
WARNING: This type of installation should only be performed by a qualified technician. Working with your
vehicle’s power system can be dangerous for you and your vehicle. If you have any concerns, consult a
professional.
Hardwire to the vehicle fuse box
STEP 1: LOCATE YOUR FUSE BOX
Check the car owner’s manual for the fuse box location. It may vary depending on the vehicle model. Remove
the plastic panel to access the fuse box. It may open simply by lifting a tab, pulling it with your fingers, or using
a flat tool to insert and separate the cover.
STEP 2: WHICH SLOT SHOULD I USE?
Use a circuit tester to test which fuse is constant (typically red) and provides 12V of power. A fuse that is
constant will stay active when the car is off. The camera will automatically enter standby mode when the car
has not moved for 10 minutes.
STEP 3: INSTRUCTIONS TO ADD-A-FUSE KIT
We recommend using the add-a-fuse kit included in our Essential Install
Package, for a more secure, long lasting installation. The add-a-fuse kit
provides a fuse slot for the existing OEM circuit (constant or ignition
switched, #2 in picture right) and another fuse slot for the new circuit for
the dashcam device (#1 in picture right).
Hardwire to the vehicle fuse box
1. Insert the new fuse tap provided in the kit into “slot 1”, and the fuse from the fuse box into “slot 2”
(Constant or Ignition Switch). If you place them in the wrong order, it will not feed power to the hardwire kit.
2. Connect the hardwiring cable with the terminal crimp connector from the add-a-fuse kit. Trim off some of
the rubber tubing to expose the wiring on your hardwiring cable. Then crimp them down together. You should
be able to crimp the fuse kit with a standard needle nose pliers. We recommend using electrical tape to
further secure the wire.
Hardwire to the vehicle fuse box
3. Connect your add-a-fuse kit to the vehicle fuse slot that you have chosen.
STEP 4: GROUND THE HARDWIRE KIT
4. The ground wire is usually in a C shape or a ring. To connect the ground wire, slip it under a metal bolt or
screw in your vehicle.
5. Loosen the bolt enough to slip the wire in and tighten (you might need a socket wrench set). A loose
ground can result in power issues for your dashcam. We recommend grounding your wire to an unpainted
bare metal bolt.
STEP 5: TEST YOUR DASHCAM
6. Plug the power cable to the dashcam. Start your vehicle to test if the dashcam powers up. Once you tested
your dashcam, run the power cable along the headliner of the car along the A-Pillar to the power source for a
clean installation.
That’s it. You’ve successfully installed your dashcam!
Adjusting the viewing angle of the V-AI12
• Dismount the V-AI12 camera from the mounting bracket on the windshield. Make sure that the mounting
bracket is not attached, as it locks the camera into position.
• Use the screwdriver to loosen the three security screws on the round side of the camera. Do not remove
the screws fully.
• Adjust the viewing angle by rotating the body of the V-AI12 and lock the three side screws when finished.
• Mount the camera back onto the windshield.
• Connect the camera to a power source (page 12).
• The camera will turn on automatically.
• To unlock the camera touch screen, enter a default PIN number 3333 (page 13).
Adjusting the viewing angle of the V-AI12
• On the main screen enter the ‘Live View’ mode.
• Use the ‘Live View’ to direct the road-facing camera and the cabin-facing camera to the proper direction.
You can use the arrow keys to switch between the views.
• Dismount the camera from the windshield and tighten the security screws. Mount the camera back on the
windshield.
Hardwire to the vehicle fuse box
• The V-AI12 may only be connected to a power source using the supplied cables.
• The camera’s cylinder side is where the input power connector is located.
• If using the USB cable as the power source, it must provide 5V DC and at least 2A.
• In order to utilize the V-AI12 full features such as active standby, the camera must be connected to a
constant 12V power source (see page 8).
Access the V-AI12 Settings menu
• Press the camera touchscreen.
• Enter the default PIN number 3333.
• The camera is now unlocked, and the Settings menu is now accessible.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
