Powerplus POWX354 Bedienungsanleitung

 POWX354 EN 
Copyright © 2021 VARO P a g e | 1www.varo.com 
1DESCRIPTION (FIG. A) ...................................................................2 
2PACKAGE CONTENT LIST.............................................................2 
3SYMBOLS ........................................................................................2 
4GENERAL POWER TOOL SAFETY WARNINGS ..........................3 
4.1 Working area...........................................................................................................3 
4.2 Electrical safety.......................................................................................................3 
4.3 Personal safety .......................................................................................................3 
4.4 Power tool use and care.........................................................................................4 
4.5 Service.....................................................................................................................4 
5ADDITIONAL SAFETY INSTRUCTIONS ........................................4 
5.1 Immediately switch off the spray gun when:.........................................................5 
5.2 Coating materials suitable for use.........................................................................5 
5.3 Coating materials not suitable for use...................................................................5 
5.4 Preparation of the coating material .......................................................................5 
6START-UP........................................................................................5 
6.1 Thinning...................................................................................................................5 
6.2 Adjusting the desired Spray Setting (Fig. 4) .........................................................6 
6.3 Adjusting the Material Volume (Fig. 5)...................................................................6 
6.4 Spray Technique.....................................................................................................7 
6.5 Interruption of work up till 4 hours max................................................................7 
7TAKING OUT OF OPERATION AND CLEANING ..........................7 
8MAINTENANCE ...............................................................................8 
8.1 Correction of Malfunctions.....................................................................................8 
9TECHNICAL SPECIFICATIONS......................................................9 
10 NOISE...............................................................................................9 
11 WARRANTY...................................................................................10 
12 ENVIRONMENT .............................................................................10 
13 DECLARATION OF CONFORMITY ..............................................11 

POWX354 EN

PAINT SPRAY GUN 500W

POWX354

WARNING! For your own safety, read this manual and the general safety

instructions carefully before using the appliance. Your power tool should

only be given to other users together with these instructions.

1 DESCRIPTION (FIG. A)

1. Air cap

2. Nozzle

3. Union nut

4. Spray gun front part

5. Trigger guard

6. Unlock button

7. Spray gun rear part

8. Air filter cover

9. Material volume adjustment

10. Mains lead

11. Container

2 PACKAGE CONTENT LIST

▪Remove all packaging materials.

▪Remove remaining packaging and packing inserts (if included).

▪Check that the package contents are complete.

▪Check the appliance, the power cord, the power plug and all accessories for transportation

damage.

▪Keep the packaging materials as far as possible until the end of the warranty period. Then

take it to your local waste disposal system.

WARNING Packaging materials are not toys! Children must not play with

plastic bags! There is a danger of suffocation!

1x manual

1x viscosity cup 1x spare nozzle (1.8 mm)

1x nozzle on pistol (2.6 mm)

If any parts are missing or damaged, please contact your dealer.

3 SYMBOLS

The following symbols are used in this manual and/or on the machine:

Denotes risk of personal injury or

damage to the tool.

Read manual before use.

In accordance with essential

safety standards of applicable

European directives.

Wear a mask In dusty

conditions.

Mandatory use of eye protection.

Wear noise protection.

POWX354 EN

4 GENERAL POWER TOOL SAFETY WARNINGS

Read all safety warnings and instructions. Failure to heed warnings and follow instructions

may result in electric shock, fire and/or serious injury. Keep safety warnings and instructions

for future reference. The term "power tool" in the safety warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless) power tool.

4.1 Working area

▪Keep working area clean and well lit. Untidy and dark areas can lead to accidents.

▪Do not operate power tools in potentially explosive surroundings, for example, in the

presence of inflammable liquids, gases or dust. Power tools create sparks which may

ignite the dust or fumes.

▪Keep children and bystanders at a distance when operating a power tool. Distractions can

cause you to lose control of it.

4.2 Electrical safety

Always check that the power supply corresponds to the voltage on the

rating plate.

▪Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

adapter plugs with earthed power tools. Unmodified plugs and matching outlets will reduce

the risk of a lethal electric shock.

▪Avoid body contact with earthed surfaces such as pipes, radiators, kitchen ranges and

refrigerators. There is an increased risk of a lethal electric shock if your body is earthed.

▪Do not expose power tools to rain or wet conditions. If water gets inside a power tool, it will

increase the risk of a lethal electric shock.

▪Do not damage the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of a lethal electric shock.

▪When operating a power tool outdoors, use an extension cable suitable for outdoor use.

Using a cord suitable for outdoor use reduces the risk of a lethal electric shock.

▪If operating a power tool in a damp location is unavoidable, use a power supply protected

by a residual current device (RCD). Using an RCD reduces the risk of a lethal electric

shock.

4.3 Personal safety

▪Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool when you are tired or under the influence of drugs, alcohol or

medication. A moment of inattention when operating a power tool may result in serious

personal injury.

▪Use safety equipment. Always wear eye protection. Using safety equipment such as a

dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed

will reduce the risk of personal injury.

▪Avoid accidental starts. Ensure the switch is in the off position before inserting the plug.

Carrying power tools with your finger on the switch or plugging in power tools when the

switch is in the on position makes accidents more likely.

▪Remove any adjusting keys or spanners before turning on the power tool. A spanner or

key left attached to a rotating part of the power tool may result in personal injury.

▪Do not reach out too far. Keep your feet firmly on the ground at all times. This will enable

you retain control over the power tool in unexpected situations.

▪Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and

gloves away from the power tool. Loose clothes, jewellery or long hair can become

entangled in the moving parts.

POWX354 EN

▪If there are devices for connecting dust extraction and collection facilities, please ensure

that they are attached and used correctly. Using such devices can reduce dust-related

hazards.

4.4 Power tool use and care

▪Do not expect the power tool to do more than it can. Use the correct power tool for what

you want to do. A power tool will achieve better results and be safer if used in the context

for which it was designed.

▪Do not use the power tool if the switch cannot turn it on and off. A power tool with a broken

switch is dangerous and must be repaired.

▪Disconnect the plug from the power source before making adjustments, changing

accessories, or storing power tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

▪Store power tools, when not in use, out of the reach of children and do not allow people

who are not familiar with the power tool or these instructions to operate it. Power tools are

potentially dangerous in the hands of untrained users.

▪Maintenance. Check for misalignment or jammed moving parts, breakages or any other

feature that might affect the operation of the power tool. If it is damaged, the power tool

must be repaired. Many accidents are caused by using poorly maintained power tools.

▪Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to jam and are easier to control.

▪Use the power tool, accessories and cutting tools, etc., in accordance with these

instructions and in the manner intended for the particular type of power tool, taking into

account the working conditions and the work which needs to be done. Using a power tool

in ways for which it was not intended can lead to potentially hazardous situations.

4.5 Service

▪Your power tool should be serviced by a qualified specialist using only standard spare

parts. This will ensure that it meets the required safety standards.

5 ADDITIONAL SAFETY INSTRUCTIONS

▪NEVER SPRAY AT PERSONS - NEVER aim the nozzle at another person or animal.

Never allow the spray to come into direct contact with the skin.

▪FLASH POINT - This spray gun must not be used for spraying flammable paints and

solvents with a flash point of less than 32 °C

▪VENTILATION - Always make sure that there is adequate ventilation in the work area

when spraying.

▪BASKET NOZZLE - Always keep the spray basket nozzle in place during use.

▪CONSIDER WORK AREA ENVIRONMENT –Do not use spray guns where there is a risk

of fire or explosion.

▪BEWARE OF ANY HAZARD - Beware of any Hazard by the material being sprayed and

consult the markings on the container or the information sup- plied by the manufacturer.

▪DO NOT SPRAY - Do not spray any material where the hazard is not known.

▪USE EYE PROTECTION - Always use appropriate eye protection to keep hazardous

vapours or fumes out of the eyes.

▪WEAR A MASK - Never operate a spray gun without wearing a face mask

▪PROTECT YOUR EARS - Wear ear protectors if the sound pressure exceeds 85 dB(A).

▪MAINTAIN YOUR TOOLS - Keep your spray gun，paint container and nozzles clean. Do

not clean with flammable liquids with a flash point less than 32 °C。Inspect the mains lead

periodically and if damaged have it replaced by a qualified person.

▪NAKED FLAMES - Never spray near a naked flame or appliance pilot flame.

▪SMOKING - Never smoke whilst spraying.

POWX354 EN

▪THINNING - Always read the paint manufacturers thinning recommendations or

instructions before using paint or other materials.

▪DISCONNECT FROM THE MAINS SUPPLY - Always disconnect from the mains supply

when filling the paint container or cleaning the spray gun.

▪SWITCH OFF WHEN NOT SPRAYING –Avoid running the unit with the flow rate knob

fully closed for any length of time.

We accept no responsibility for damage caused by the use of unsuitable

substances, or paints that have not been thinned correctly, and any health

hazards that arise from lack of adequate ventilation.

5.1 Immediately switch off the spray gun when:

▪Interruption in the mains plug, mains lead or mains lead damage.

▪Defect switch.

▪Smoke or stench of scorched isolation.

5.2 Coating materials suitable for use

Water- and solvent-based paints, finishes, primers, 2-component paints, clear finishes,

automotive finishes, staining sealers and wood sealer-preservatives.

5.3 Coating materials not suitable for use

Wall paints (emulsion paints) etc., alkali and acidic paints. Coating materials with a flash point

below 21 °C.

5.4 Preparation of the coating material

The enclosed spray attachment can be used to spray paints, varnishes and glazes that are

undiluted or slightly diluted.

▪Stir the material up and put the required amount into the paint container.

Thinning recommendation

Sprayed material

Glazes

undiluted

Wood preservatives, mordants, oils, disinfection

agents, plant protective agents

undiluted

Paints containing solvents and water-soluble

paints, primers, vehicle coating paints,

hick-flm glazes

dilute by 5 - 10%

▪If the convey capacity is too low, add 5 - 10% dilution step-by-step until the convey

capacity fulfils your requirements.

6 START-UP

6.1 Thinning

Always remember to disconnect from the mains supply before filling the

paint container with sprayable material.

Most paints are supplied ready for brush application and will need to be thinned before they

are suitable to be sprayed. Follow the manufacturer’s advice on thinning. The paint when

used with a spray gun. The viscosity cup will help you to determine the correct viscosity of

paint to be used. To determine the correct viscosity, fill the cup to the brim with the paint.

Measure the amount of time it takes for the cup to empty back into the can.

The table below shows recommended times for different types of material.

POWX354 EN

If the paint takes longer than the recommended time to empty, then further thinning is required.

Mix in a small quantity of the appropriate thinner and use the viscosity test until the correct

thickness is achieved. Some sprayable materials contain particles and lumps. These materials

should be strained before filling the paint container.

Before connecting to the mains supply, be sure that the supply voltage is identical with the

value given on the rating plate.

▪Unscrew the container from the spray gun.

▪Aligning suction tube (Fig. 2).

If the suction tube is positioned correctly, the container contents can be sprayed without

almost any residue.

When working on lying objects: Turn the suction tube forwards (Fig. 2 A).

Spraying work when working on overhead objects: Turn the suction tube rearwards (Fig. 2 B).

▪Set the container on a sheet of paper, pour in the prepared coating material and screw the

container tightly onto the spray gun.

▪Put the machine down only on a level, clean surface. Otherwise the machine could tip

over!

▪Adjust the spray setting on the spray gun.

Three different spray jet settings can be chosen on the spray gun, depending on the

application and target object.

Selecting the Spray Setting

Fig. 3 A = horizontal fat jet

Fig. 3 B = circular jet

Fig. 3 C = vertical fat jet

The spray pattern indication can be found on the front part of the sprayer (Fig.3D, A). With the

arrowhead towards the boss on the tip (Fig.3D, B).

6.2 Adjusting the desired Spray Setting (Fig. 4)

With the union nut (2) slightly unscrewed, turn the air cap (1) to the desired spray setting

position. Then tighten the union nut.

WARNING! Danger of injury! Never pull the trigger guard while adjusting the

air cap.

6.3 Adjusting the Material Volume (Fig. 5)

Set the material volume by turning the regulator on the trigger guard of the spray gun.

- turn to downside lower material volume.

+ turn to upside higher material volume.

Viscosity Table

Spray material

Runout Time in Seconds

Oil enamel

25-45

Oil based primer

30-50

Varnish

20-55

Lacquer / lacquer sanding sealer

25-40

Oil stain

No thinning required

Clear sealer

No thinning required

Polyurethane

No thinning required

POWX354 EN

6.4 Spray Technique

▪The spray result depends heavily on the smoothness and cleanliness of the surface to be

sprayed. Therefore the surface should be carefully prepared and kept free of dust.

▪Cover all surfaces not to be sprayed.

▪Cover screw threads or similar parts of the target object.

▪It is advisable to test the spray gun on cardboard or a similar surface to find the correct

setting.

Important: Begin spraying outside of the target area and avoid interruptions

inside the target area.

▪Correct (Fig. 6a): Be sure to hold the spray gun at an even distance of approx. 10 –30 cm

to the target object.

▪Incorrect (Fig. 6b): Heavy spray fog build-up, uneven surface quality.

▪Move the spray gun evenly cross-wise or up-and-down, depending on the spray pattern

setting.

▪An even movement of the spray gun results in an even surface quality.

▪When coating material builds up on the nozzle (A) and air cap (B) (Fig. 7), clean both parts

with a solvent or water.

6.5 Interruption of work up till 4 hours max.

▪Turn the machine off.

▪When processing 2-component varnishes, clean the device immediately.

7 TAKING OUT OF OPERATION AND CLEANING

Proper cleaning is the prerequisite for problem-free operation of the paint application device.

No warranty claims are accepted in case of improper or no cleaning.

▪Unplug the power plug. Vent the container in case of longer breaks and after the work has

been terminated. This can be done by briefly turning open and then closing the container

or by pulling the trigger guard and letting the paint into the original paint container.

▪Divide the spray gun. Press the unlock button (Fig. 8 A) downwards.

▪Unscrew the container. Empty any remaining coating material back into the material tin.

▪Preclean the container and suction tube with a brush.

▪Pour solvent or water into the container. Screw the container back on. Use only solvents

with a flashpoint over 21 °C .

▪Assemble the gun again.

▪Insert the power plug, turn on the machine and spray the solvent or water into a container

or a cloth.

▪Repeat the above procedure until the solvent or water emerging from the nozzle is clear.

▪Turn of the machine and remove the plug.

CAUTION! Never clean seals, diaphragm and nozzle or air holes of the

spray gun with metal objects.

The ventilation hose and diaphragm are only solvent-resistant to a limited

extent. Do not immerse in solvent, only wipe.

WARNING! Never hold the spray gun rear part under water or immerse it

into liquids. Clean the housing only with a moistened cloth.

POWX354 EN

▪Clean the outside of the spray gun and container with a cloth soaked in solvent or water.

▪Unscrew the union nut and remove the air cap and nozzle. Clean the air cap and nozzle

with a brush and solvent or water.

8 MAINTENANCE

Change the air filter if it is soiled (Fig. 9, item 7).

WARNING! Never operate the machine without the air filter; dirt could be

sucked in and interfere with the function of the machine.

8.1 Correction of Malfunctions

Problem

Cause

Remedy

No coating material

emerges from the

nozzle

Nozzle clogged

Feed tube clogged

Material volume setting turned too far

to the left (-)

Feed tube loose

No pressure build-up in container

Clean

Turn to the right (+)

Insert

Tighten container

Coating material drips

from the nozzle

Nozzle loose

Nozzle worn

Nozzle seal worn

Coating material assembly at air cap,

nozzle or needle

Tighten

Change

Clean

Atomization too

coarse

Viscosity of coating material too high

Material volume too large

Material volume adjusting screw

turned too far to the right (+)

Nozzle contaminated

Air filter heavily soiled

Too little pressure build-up in

container

Thin

Turn material volume

adjusting screw to the

left (-)

Clean

Change

Tighten container

Spray jet pulsates

Coating material in container running

out

Air filter heavily soiled

Refill

Change

Coating material

causes "paint tears"

Too much coating material applied.

Turn material volume

adjusting screw to the

left (-)

Too much fog of

coating material

(Overspray)

Distance to the object too large

Too much coating material applied

Reduce distance Turn

material volume

adjusting screw to the

left (-)

Paint in the

ventilating hose

Diaphragm soiled

Diaphragm defective

Clean the diaphragm

Replace the diaphragm

POWX354 EN

9 TECHNICAL SPECIFICATIONS

Rated Power

500 W

Rated voltage

220-240 V

Rated frequency

50 Hz

Carbon brush motor

Yes

Diameter nozzle

2.6 mm

Adjustable nozzle

Yes

Flow speed

900g/min

Max viscosity

100 din/sec

Cable length

2 m

Tank capacity

0.8 l

Adjustable paint flow control

Yes

Easy cleaning

Yes

Spray patterns

Round spray pattern

Yes

Horizontal spray pattern

yes

Vertical spray pattern

Yes

Quick change filter

Yes

Quick release

Yes

Soft grip

Yes

10 NOISE

Noise emission values measured according to relevant standard. (K=3)

Acoustic pressure level LpA

82 dB(A)

Acoustic power level LwA

93 dB(A)

ATTENTION! Wear hearing protection when sound pressure is over 85

dB(A).

aw (Vibration)

<2.5 m/s²

K = 1.5 m/s²

POWX354 EN

11 WARRANTY

▪This product is warranted as provided by law for a 36 -month period effective from the

date of purchase by the first user.

▪This warranty covers all material or production flaws excluding : batteries, chargers,

defective parts subject to normal wear & tear such as bearings, brushes, cables, and

plugs, or accessories such as drills, drill bits, saw blades, etc. ; damage or defects

resulting from maltreatment, accidents or alterations; nor the cost of transportation.

▪Damage and/or defects resulting from inappropriate use also do not fall under the

warranty provisions.

▪We also disclaim all liability for any bodily injury resulting from inappropriate use of the

tool.

▪Repairs may only be carried out by an authorised customer service centre for Powerplus

tools.

▪You can always obtain more information at the number 00 32 3 292 92 90.

▪Any transportation costs shall always be borne by the customer, unless agreed otherwise

in writing.

▪At the same time, no claim can be made on the warranty if the damage of the device is the

result of negligent maintenance or overload.

▪Definitely excluded from the warranty is damage resulting from fluid permeation, excessive

dust penetration, intentional damage (on purpose or by gross carelessness), inappropriate

usage (use for purposes for which the device is not suitable), incompetent usage (e.g. not

following the instructions given in the manual), inexpert assembly, lightning strike,

erroneous net voltage. This list is not exhaustive.

▪Acceptance of claims under warranty can never lead to the prolongation of the warranty

period nor commencement of a new warranty period in case of a device replacement.

▪Devices or parts which are replaced under the warranty therefore remain the property of

Varo NV.

▪We reserve the right to reject a claim whenever the purchase cannot be verified or when it

is clear that the product has not been properly maintained. (Clean ventilation slots, carbon

brushes serviced regularly, etc.).

▪Your purchase receipt must be kept as proof of date of purchase.

▪Your appliance must be returned undismantled to your dealer in an acceptably clean state,

(in its original blow-moulded case if applicable to the unit), accompanied by proof of

purchase.

12 ENVIRONMENT

Should your appliance need replacement after extended use, do not discard it

with the household rubbish but dispose of it in an environmentally safe way.

Waste produced by electrical machine items should not be handled like normal

household rubbish. Please recycle where recycle facilities exist. Check with your

Local Authority or retailer for recycling advice.

Inhaltsverzeichnis

Andere Powerplus Spritzpistole Handbücher

Powerplus

Powerplus POWX350 Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Graco

Graco 246737 Gebrauchs- und Pflegehandbuch

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

Graco

Graco EM 390 Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung