PowerShield 1100 VA Bedienungsanleitung

Uninterruptible Power Supply System

www.powershield.com.au

Commander RT

1100/2000/3000 VA

Line Interactive Sinewave UPS

IMPORTANT

Download latest software

www.powershield.com.au/downloads

NetGuard®

User Manual

www.powershield.com.au 1

Introduction

Thank you for choosing PowerShield.

PowerShield Commander RT UPS series are designed to provide the highest level of protection

against disturbances found on electrical power supply lines. It is suitable for most applications

including IT, security, telephone, broadcasting, medical etc.

The Commander UPS series are designed to provide the most comprehensive protection for your

valuable electronic equipment, hardware, software and data from harmful disturbances found on

AC power lines including blackouts, power sags, power surges, under voltage, over voltage, line

noise, frequency variation, switching transients and harmonic distortions. The Commander RTs

will continuously protect your equipment by internally isolating your equipment from the utility

power ensuring that all your equipment always receives clean, uninterrupted and stable power.

Very Important !! : WARRANTY REGISTRATION

In order to validate product warranty, it is essential that you register your UPS on line.

Please Visit PowerShield on line product warranty web page

www.powershield.com.au/product-registration.php

This user manual contains instructions relating to safety, installation, operation, maintenance and

warranty of this product.

Please keep this manual in a safe place for future references.

www.powershield.com.au 2

Special Symbols

The following are examples of symbols used on the UPS to alert you the important

information.

RISK OF ELECTRIC SHOCK -

Indicates that a risk of electric shock is present and the associated

warning should be observed

CAUTION; REFER TO OPERATOR’S MANUAL -

Refer to your operator’s manual for additional information, such as

important operating and maintenance.

SAFETY EARTHING TERMINAL -

Indicates the primary safety ground.

This symbol indicates that you should not discard the UPS or the UPS

batteries in the trash. The UPS may contain sealed, lead-acid

batteries. Batteries must be recycled.

www.powershield.com.au 3

Table of Contents

1. Important Safety Warning..........................................................................................4

1-1. Transportation..........................................................................................................4

1-2. Preparation ..............................................................................................................4

1-3. Installation...............................................................................................................4

1-4. Operation.................................................................................................................5

1-5. Maintenance, service and faults.................................................................................5

2. Installation And Setup ........................................................................................................6

2-1. Rear Panel View .......................................................................................................6

2-2. Installation of the UPS ..............................................................................................7

2-3. Setup the UPS..........................................................................................................7

3. Operations....................................................................................................................... 10

3-1. Button Operation.................................................................................................... 10

3-2. LCD Panel .............................................................................................................. 10

3-3. Audible Alarm......................................................................................................... 11

3-4. LCD Display Wordings Index.................................................................................... 12

3-5. UPS Setting............................................................................................................ 12

3-6. Operating Mode Description.................................................................................... 15

3-7. Faults Reference Code............................................................................................. 16

3-8. Warning Indicator................................................................................................... 16

4. Troubleshooting ............................................................................................................... 17

4-1. Battery Replacement............................................................................................... 18

4-2. Battery Kit Assembly (option).................................................................................. 19

5. Service ............................................................................................................................ 21

6. Storage and Maintenance ................................................................................................. 22

6-1. Operation............................................................................................................... 22

6-2. Storage.................................................................................................................. 22

7. Contacting PowerShield..................................................................................................... 22

8. Specifications................................................................................................................... 23

www.powershield.com.au 4

1. Important Safety Warning

Please comply with all warnings and operating instructions in this manual. Save this manual

properly and read carefully the following instructions before installing the unit. Do not operate

this unit before reading through all safety information and operating instructions carefully

1-1. Transportation

Please transport the UPS system only in the original package to protect against shock

and impact.

Handling Safety

Do not lift heavy loads without assistance.

This equipment is intended for installation in a controlled temperature indoor area free

from conductive contaminants.

1-2. Preparation

Condensation may occur if the UPS system is moved directly from cold to warm

environment. The UPS system must be absolutely dry before being installed. Please

allow at least two hours for the UPS system to acclimate to the environment.

Do not install the UPS system near water or in moist environments.

Do not install the UPS system where it would be exposed to direct sunlight or near

heater.

Do not block ventilation holes in the UPS housing.

1-3. Installation

Do not connect appliances or devices which would overload the UPS system (e.g. laser

printers) to the UPS output sockets.

Place cables in such a way that no one can step on or trip over them.

Do not connect domestic appliances such as hair dryers to UPS output sockets.

The UPS can be operated by any individuals with no previous experience.

Connect the UPS system only to an earthed shockproof outlet which must be easily

accessible and close to the UPS system.

Please use only VDE-tested, CE-marked mains cable (e.g. the mains cable of your

computer) to connect the UPS system to the building wiring outlet (shockproof outlet).

Please use only VDE-tested, CE-marked power cables to connect the loads to the UPS

system.

Pluggable equipment includes a protective earth conductor that carries the leakage

current from the load devices ( computer equipment ). Total leakage current must not

exceed 3.5mA.

www.powershield.com.au 5

1-4. Operation

Do not disconnect the mains cable on the UPS system or the building wiring outlet

(shockproof socket outlet) during operations since this would cancel the protective

earthing of the UPS system and of all connected loads.

The UPS system features its own, internal current source (batteries). The UPS output

sockets or output terminals block may be electrically live even if the UPS system is not

connected to the building wiring outlet.

In order to fully disconnect the UPS system, first press the OFF/Enter button to

disconnect the mains.

Prevent no fluids or other foreign objects from inside of the UPS system.

1-5. Maintenance, service and faults

The UPS system operates with hazardous voltages. Repairs may be carried out only by

qualified maintenance personnel.

Caution - risk of electric shock. Even after the unit is disconnected from the mains

(building wiring outlet), components inside the UPS system are still connected to the

battery and electrically live and dangerous.

Before carrying out any kind of service and/or maintenance, disconnect the batteries

and verify that no current is present and no hazardous voltage exists in the terminals of

high capability capacitor such as BUS-capacitors.

Only persons are adequately familiar with batteries and with the required precautionary

measures may replace batteries and supervise operations. Unauthorized persons must

be kept well away from the batteries.

Caution - risk of electric shock. The battery circuit is not isolated from the input

voltage. Hazardous voltages may occur between the battery terminals and the ground.

Before touching, please verify that no voltage is present!

Batteries may cause electric shock and have a high short-circuit current. Please take the

precautionary measures specified below and any other measures necessary when

working with batteries:

－remove wristwatches, rings and other metal objects

－use only tools with insulated grips and handles.

When changing batteries, install the same number and same type of batteries.

Do not attempt to dispose of batteries by burning them. This could cause battery

explosion.

Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and

eyes. It is toxic.

Please replace the fuse only with the same type and amperage in order to avoid fire

hazards.

Do not dismantle the UPS system.

www.powershield.com.au 6

2. Installation And Setup

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is

damaged. Please keep the original package in a safe place for future use.

2-1. Rear Panel View

PSCRT1100

PSCRT2000

PSCRT3000

1. Programmable outlets: connect to non-critical loads.

2. Output receptacles: connect to mission-critical loads.

3. AC input

4. Input circuit breaker

5. Emergency power off function connector (EPO)

6. USB communication port

7. RS-232 communication port

8. SNMP intelligent slot

9. External battery connector (only available for 2000/3000 models)

10. External battery pack numbers detection port

www.powershield.com.au 7

2-2. Installation of the UPS

COMMANDER RT Series can be mounted vertically and horizontally. Please installation below for

tower and rack mount installation steps.

Rack-mount Installation

Step 1 Step 2

Tower Installation

Step 1

Step 2

Step 3

2-3. Setup the UPS

Step 1: UPS input connection

Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension cords.

Step 2: UPS output connection

There two kinds of outputs: programmable outlets( white coloured outlets )and general

outlets ( black coloured outlets ).

Please connect non-critical devices to the programmable outlets and critical devices to

the general outlets.

During power failure, you may extend the backup time to critical devices by setting shorter

backup time for non-critical devices.

www.powershield.com.au 8

Step 3: Communication connection

Interface ports:

USB port RS-232 port Intelligent slot

To allow for unattended UPS shutdown/start-up and status monitoring, connect the

communication cable one end to the USB/RS-232 port and the other to the communication port

of your PC. With the monitoring software installed, you can schedule UPS shutdown/start-up and

monitor UPS status through PC.

The Commander RT series are equipped with intelligent slot perfect for either SNMP or AS400

card. When installing either SNMP or AS400 card in the UPS, it will provide advanced

communication and monitoring options.

NOTE : USB port and RS-232 port cannot work at the same time.

Step 5: EPO ( Emergency Power OFF ) function

Keep the pin 1 and pin 2 closed for UPS normal operation. To activate EPO function, cut the wire

between pin 1 and pin 2.

Step 6: External battery connection (for Commander RT 2000 and 3000)

Connect one end of external battery cable to UPS unit and the other end to battery box. Use

supplied battery detection wire in detection port of UPS unit and plug the other end to battery

bank. See below chart for detailed connection.

Models : PSCRT2000,PSCRT3000

PSRTBB8(2K only)/PSRTBB12(3K only)

NOTE: Maximum connected external battery boxes up to 2 units.

It’s in closed status for UPS

normal operation.

www.powershield.com.au 9

Step 7: Turn on the UPS

Press the ON/Mute button on the front panel for two seconds to power on the UPS.

Note: The battery charges fully during the first five hours of normal operation. Do not

expect full battery run capability during this initial charge period.

Step 8: Install software

Install NetGuard UPS monitoring software to fully configure UPS shutdown. Please follow steps

below to download and install monitoring software:

1. Go to the website http://www.powershield.com.au/downloads

2. Click NetGuard software icon and then choose your required OS to download the software.

3. Follow the on-screen instructions to install the software.

4. When your computer restarts, the monitoring software will appear as an orange plug icon

located in the system tray, near the clock.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere PowerShield UPS Handbücher

PowerShield

PowerShield defender PSD 650 Bedienungsanleitung

PowerShield

PowerShield Centurion Series Bedienungsanleitung

PowerShield

PowerShield Centurion PSCER6000 Bedienungsanleitung

PowerShield

PowerShield Centurion RT 6000VA Bedienungsanleitung

PowerShield

PowerShield Defender 1200 Bedienungsanleitung

PowerShield

PowerShield Centurion 10000 VA Bedienungsanleitung

PowerShield

PowerShield Pilot DC 50 Bedienungsanleitung

PowerShield

PowerShield PSCM1100 Bedienungsanleitung

PowerShield

PowerShield SAFEGUARD PSG750 Bedienungsanleitung

PowerShield

PowerShield DC Pilot 50 Bedienungsanleitung

PowerShield

PowerShield Centurion Pro Series Bedienungsanleitung

PowerShield

PowerShield AS400 Bedienungsanleitung

PowerShield

PowerShield GLADIATOR Bedienungsanleitung

PowerShield

PowerShield 8 Bedienungsanleitung

PowerShield

PowerShield Centurion PSCE1000 Bedienungsanleitung

PowerShield

PowerShield Centurion RT Series Bedienungsanleitung

PowerShield

PowerShield Defender Series Bedienungsanleitung

PowerShield

PowerShield PSDCMin12 Bedienungsanleitung

PowerShield

PowerShield Ninja Slimline PSLN600 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung