PowerTech MP-4554 Bedienungsanleitung

45 WATT SOLAR KIT

INSTRUCTION MANUAL

MP-4554

Distributed by:

Electus Distributio Pty. Ltd.

320 Victoria Road

Rydalmere NSW 2116 Australia

Pho e: 1300 738 555

Facsimile: 1300 738 500

www.electusdistributio .com.au

Made i Chi a

Specifications

Pa el Dime sio s 315mm W x 925mm L x 22mm Thick

Pa el 15 watts per pa el, 14.5 volts output (worki g)

Peak Voltage 23.5 Voc (Ope Circuit Volts)

Nomi al Voltage 14.5 volts battery output

Adaptor Outlets from regulator 3 VDC, 6 VDC, 12 VDC, 12 VDC

USB output

12VDC female CLA output

I verter female CLA output (for 12V i verter)

Accessory 2 pcs of 5W 12VDC e ergy savi g lamp

Multi purpose wire

Battery clamp wire

Save This Manual

You will eed the ma ual for the safety war i gs a d precautio s, assembly i structio s, operati g a d mai te a ce

procedures, parts list a d diagram. Keep your i voice with this ma ual. Write the i voice umber o the i side of the fro t

cover. Keep the ma ual a d i voice i a safe a d dry place for future refere ce.

Safety Warnings and recautions

WARNING: When using product, basic safety precautions should always be followed to reduce the risk of

personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean. Cluttered areas i vite i juries.

2. Observe work area conditions.Do ot use the Regulator i damp or wet locatio s. Do ’t expose Regulator to rai .

Do ot use electrically powered products i the prese ce of flammable gases or liquids.

3. Keep children away. Childre must ever be allowed i the work area. Do ot let them ha dle product, accessories, or

cords.

4. Store idle equipment.Whe ot i use, products must be stored i a dry locatio to i hibit rust. Always lock up

products a d keep out of reach of childre .

5. Use the right product for the job. Do ot attempt to force a small product to do the work of a larger i dustrial

product. There are certai applicatio s for which this product was desig ed. It will do the job better a d more safely at the

rate for which it was i te ded. Do ot modify this product a d do ot use this product for a purpose for which it was ot

i te ded.

6. Dress properly. Do ot wear loose clothi g or jewelry as they ca be caught i parts duri g i stallatio . Protective,

electrically o co ductive clothes a d o skid footwear are recomme ded whe worki g. Wear restrictive hair coveri g to

co tai lo g hair.

7. Use eye protection. Always wear ANSI-approved impact safety goggles duri g assembly a d whe worki g with tools

a d equipme t.

8. Do not overreach. Keep proper footi g a d bala ce at all times. Do ot reach over or across wires or cables.

9. Maintain products with care. Keep products clea for better a d safer performa ce. Follow i structio s for cha gi g

accessories. I spect product cords periodically, a d if damaged, have them repaired by a authorized tech icia . The pa els

must be kept clea , dry, a d free from oil a d grease at all times.

10. Disconnect power. U plug from accessories or batteries whe ot i use a d disco ect the

Solar Pa els from the Regulator at ight.

11. Stay alert. Watch what you are doi g, use commo se se. Do ot operate a y product whe you are tired.

12. Check for damaged parts. Before usi g a y product, a y part that appears damaged should be carefully checked to

determi e that it will operate properly a d perform its i te ded fu ctio . Check for alig me t a d bi di g of parts; a y

broke parts or mou ti g fixtures; a d a y other co ditio that may affect proper operatio . A y part that is damaged should

be properly repaired or replaced by a qualified tech icia . Do ot use the product if a y switch does ot tur O a d Off

properly.

13. Guard against electric shock. Preve t body co tact with grou ded surfaces such as pipes, radiators, ra ges, a d

refrigerator e closures.

14. Replacement parts and accessories. Whe servici g, use o ly ide tical replaceme t parts. Use of a y other parts will

void the warra ty. O ly use accessories i te ded for use with this tool. Approved accessories are available from Harbor

Freight Tools.

15. Do not operate product if under the influence of alcohol or drugs. Read war i g labels if taki g prescriptio

medici e to determi e if your judgme t or reflexes are impaired while taki g drugs. If there is a y doubt, do ot operate the

product.

16. Maintenance. For your safety, service a d mai te a ce should be performed regularly by a qualified tech icia .

Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all

possible conditions and situations that may occur. It must be understood by the operator that common sense

and caution are factors which cannot be built into this product, but must be supplied by the operator.

Unpacking

Whe u packi g, check to make sure the parts listed o page 7 are i cluded. If a y parts are missi g or broke , please call

Harbor Freight Tools at the umber o the cover of this ma ual as soo as possible.

Assembly

1. Slide the Left a d Right Tria gle Frame (6a a d 6b) i to

slot 1 a d slot 3 o both e ds of the Top Li k Bar (6d) a d

Bottom Li k Bar (6C) (to form the frame assembly). See to

right.

2. Push the Top Li k Bar (6d) dow to slot 2 (to lock the

frame assembly).

See to right.

3. Determi e where you wa t to positio the Frame

Assembly (6a-6d) maki g sure it is faci g south (for

maximum su exposure) with o obstructio s i fro t of

it. The Regulator (2) must be i a dry, well ve tilated

locatio earby. If ecessary, build a small structure that

guara tees the u it will stay dry duri g rai or s ow, a d,

provide e ough ve tilatio to allow the u it to ve t a d

cool properly.

4. Secure the Frame Assembly (6a-6d) to its mou ti g locatio usi g hardware ( ot supplied) through the four holes o

the bottom of the Left a d Right Triangle Frames (6a & 6b).

5. Carefully place each Solar anel (1) o the fro t of the Frame Assembly (6a-6d) so that the bottom of each pa el fits

i to the slot o the bottom of the Frame Assembly (6a-6d).

6. Lock the two eye hooks o the back-ce ter frame i to the two protrudi g bolts o the Top Link Bar (6d).

Caution: If the u it is to be mou ted o a rooftop, always be especially careful whe climbi g ladders a d walki g o sloped

roofs. Additio al hardware may have to be purchased if perma e tly mou ti g the Solar pa els o a rooftop.

7. Co ect the two ri g co ectors at the e d of the lead wires comi g from the Solar anels (1) to the Solar Termi als

o the Regulator (2). See FIGURE 1. Be sure to co ect by matchi g polarities o the wires a d the Regulator (2). Black

(-) is egative a d red (+) is positive. The , co ect the wire leads so that all of the Solar anels (1) are co ected to each

other a d the Regulator (2) (agai , maki g sure you are hooki g up to the right polarity o the Regulator).

See Hook-Up Diagram, right.

Figure 1.

Operation

Note: Performa ce of the Solar Pa els will vary depe de t o site locatio , a gle of the pa els i relatio to the arc of the

su , a d available su light.

Recharging a Battery ( ot i cluded).

1. To recharge a 12 volt battery ( ot i cluded), payi g atte tio to the proper polarity (black (-) is egative a d red (+) is

positive), co ect the two ri g termi als o the Battery Clamp wire (3) to the Battery Termi als o the back of the

Regulator (2). See FIGURE 1. The , co ect the black clamp to the black or egative (-) termi al o the battery ( ot

i cluded). Fi ally, co ect the red clamp to the red or positive (+) termi al o the battery. Always avoid accide tal co tact of

the red a d black battery clamps to each other.

Note: Do ot cha ge the order explai ed i umber 1 above or electric shock resulti g i serious i jury or death may occur.

2. Tur o the Regulator. See the O /Off switch i FIGURE 2.

3. Never leave the battery ( ot i cluded) u atte ded while chargi g. Whe the battery ( ot i cluded) is fully charged, the

readi g o the voltage display will show “13” or above. Note: the voltage display will have to be tur ed o i order to

mo itor the batter voltage. (It is recomme ded to leave the voltage display off whe ot mo itori g the battery voltage si ce

it co sumes e ergy.) Twelve (12) Volt batteries should charge to 13 Volts for a full charge. If the i te t is to stop chargi g the

battery, disco ect the solar pa els from the charge regulator. Note: The charge regulator provides “over charge”

protectio . If the battery voltage is higher tha 14.5 V, the regulator will shut off charge from solar pa el.

Figure 2.

Operation (continued)

The Regulator (2) provides the followi g protectio while chargi g:

A. Over-discharge rotection: Whe the electricity level of the battery ( ot i cluded) goes too low (below 11 volts) the

Regulator (2) will automatically shut off the power output to preve t damage to the battery ( ot i cluded). If this occurs,

stop usi g the battery ( ot i cluded) a d charge it u til the Voltage display shows 13 volts.

B. Overcharge rotection: If the electricity level o the battery ( ot i cluded) goes too high (above 14.5 volts) the

Regulator (2) will automatically shut off power i put to preve t damage to the battery ( ot i cluded).

C. Overload rotection: If the output curre t exceeds 4 amps the fuse (See FIGURE 1) will blow to preve t damage to

the co troller i the Regulator (2). If this occurs, have a authorized service tech icia replace the fuse.

Note: The On/Off switch of the charge regulator must be in the “On” position to activate the three

protection functions mentioned above.

4. Inverter female CLA output (See Figure 2) ca be co ected to Car inverters ( ot i cluded) to power small AC

applicatio s like TV. This output draw power directly from Rechargeable battery. A d is ot bei g regulated by this solar

charge regulator.

Using the 12 Volt Lights and Accessories.

Note: The Charge Regulator must be i “ON” positio at all times.

1. If the 12 Volt Lights (4) are ’t already attached to the sockets o the e d of each Light Wire (7), ge tly s ap them i .

2. Plug the other e d of the Light Wire (7) i to a y o e of the 12 Volt DC outlets o the Regulator (2) as show i

FIGURE 2 a d switch o the light. You may plug i the other 12 Volt Light (4) to either 12 Volt DC outlet.

3. To tur off the lights, switch off or u plug the Light Wire (7) from the 12 Volt DC outlet o the Regulator (2).

Note: This system ca also be used to power other small 3 Volt DC, 6 Volt DC small applia ces.

4. Plug the appropriate plug o the Multi urpose Adaptor (5) i to the applia ce. The adaptor has 3 Volt DC, 6 Volt DC

output.

5. I sert the plug o the other e d of the wire attached to the Multi urpose Adaptor (5) i to the appropriate DC Outlet

o the Regulator (2). For your refere ce, FIGURE 2 shows the adaptor wire plugged i to the 3 Volt DC outlet.

6. Operate your applia ce.

7. Whe fi ished, u plug the Multi urpose Adaptor (5) wire plug from the Regulator (2) a d the u plug the Multi

urpose Adaptor (5) from the applia ce.

Maintenance

When servicing the Solar anels, Regulator, or Accessories, first disconnect the cable from the Regulator to

the Solar anels.

1. Periodically, ge tly clea the surface of the Solar Pa els with a wet, soft cloth.

2. Check the cable co ectio s before each use.

Assembly Drawing

(7) lamp wire

(4) 12Volt light

(2) regulator

(5) multi-purpose wire

(1) solar panel

(3) Battery clamp

Inhaltsverzeichnis

Andere PowerTech Solarpanel Handbücher

PowerTech

PowerTech ZM9157 Bedienungsanleitung

PowerTech

PowerTech ZM9124 Bedienungsanleitung

PowerTech

PowerTech ZM9178 Bedienungsanleitung

PowerTech

PowerTech ZM9124 Bedienungsanleitung

PowerTech

PowerTech ZM9137 Bedienungsanleitung

PowerTech

PowerTech ZM9158 Bedienungsanleitung

PowerTech

PowerTech ZM9159 Bedienungsanleitung

Beliebte Solarpanel Handbücher anderer Marken

Navitron

Navitron HFC-2 Bedienungsanleitung

AXITEC

AXITEC 60-CELL Bedienungsanleitung

thermital

thermital TSOL 20 N BLU Bedienungsanleitung

AZO Digital

AZO Digital MPPT-3000 Bedienungsanleitung

Clenergy

Clenergy PV-ezRack SolarTripod Bedienungsanleitung

Beretta

Beretta SCF-20N Bedienungsanleitung

moovo

moovo KSM001 Produkthandbuch

solarwatt

solarwatt EasyIn 60M Series Bedienungsanleitung

Solarland

Solarland Portable Series Handbuch

Ubiquiti

Ubiquiti sunMAX Bedienungsanleitung

Lippert

Lippert Furrion FSFP37MW-BL Bedienungsanleitung

Sonnenkraft

Sonnenkraft GK5-HP Bedienungsanleitung

REC

REC TwinPeak 2S Mono 72 Series Bedienungsanleitung

Sunforce

Sunforce 50039 Bedienungsanleitung

Flexsolar

Flexsolar C100 Leitfaden

Süd Solar

Süd Solar 03005 Bedienungsanleitung

Kodak

Kodak SP21 Bedienungsanleitung

Carmanah

Carmanah Go Power! Solar Flex GP-FLEX-30 Bedienungsanleitung