Powervar GTS Series Bedienungsanleitung

GTS Series

User Manual

2 A01-00030 Rev D

1.0 - Introduction ...................................................................... 5

2.0 - Safety Instructions............................................................ 8

3.0 - Installation.........................................................................11

4.0 - Operation .........................................................................15

5.0 - Maintenance ...................................................................20

6.0 - Specications ................................................................. 24

7.0 - Troubleshooting ..............................................................30

8.0 - Warranty .........................................................................31

TABLE OF CONTENTS

3A01-00030 Rev D

IMPORTANT NOTICE ON BATTERY WARRANTY

The warranty policies stated in Sections 1 and 8 are not valid

for applications in which the UPM is regularly and intentionally

disconnected from AC mains power. POWERVAR’s two year battery

warranty applies only to products that are properly installed and

consistently connected to AC mains power, except during utility

outages.

Products regularly and intentionally disconnected from AC

mains power will experience substantially reduced battery life.

Notwithstanding the stated warranty in Sections 1 and 8.

POWERVAR’s standard warranty term does not apply in these cases

and is supplanted by a 90 day warranty from time of shipment from

POWERVAR. The warranty provided by POWERVAR provides for

the replacement of the battery or battery systems in the event that

the batteries do not meet performance specications as determined

by POWERVAR exclusively.

4A01-00030 Rev D

Danger- The danger symbol is used to indicate

imminently hazardous situations, locations, and

conditions which, if not avoided, WILL result in death,

serious injury, and/or severe property damage.

Attention- The attention warning symbol is used

to indicate situations and conditions that can cause

operator injury and/or equipment damage.

Caution- The caution symbol is used to indicate

potentially hazardous situations and conditions which,

if not avoided, may result in injury. Equipment damage

may also occur.

Warning- The warning symbol is used to indicate

potentially hazardous situations and conditions which,

if not avoided, COULD result in serious injury or death.

Severe property damage COULD also occur.

Other warning symbols may appear along with the

Danger and Caution symbol and are used to specify

special hazards. These warnings describe particular

areas where special care and/or procedures are

required in order to prevent serious injury and possible

death

Electrical warnings- The electrical warning symbol

is a lightning bolt mark enclosed in a triangle. The

electrical warning symbol is used to indicate high

voltage locations and conditions may cause serious

injury or death.

Explosion warnings- The explosion warning symbol

is an explosion mark enclosed in a triangle. The

explosion warning symbol is used to indicate locations

and conditions where molten, exploding parts may

cause serious injury or death if the proper precautions

are not observed.

DANGER

CAUTION

WARNING

ATTENTION

5A01-00030 Rev D

1.0 INTRODUCTION

Thank You

Thank you for your purchase of this power conditioning solution. Our

broad family of power quality solutions are designed to protect sensitive

electronic systems from the destruction, degradation, and disruption

caused by electrical power disturbances.

This product you have purchased is the most advanced solution

available today. It protects and provides clean power to your system.

We’ve prepared this document to help familiarize you with the functions

and controls of this product. If, after reviewing this manual, you have any

questions at all, please feel free to contact our technical support team by

phone (1-800-369-7179) or email us at servicerma@powervar.com.

Registering your POWERVAR Product

Please take a few moments to register your product purchase.

Registration is easy and quick via the product registration page found on

our website at www.powervar.com.

6 A01-00030 Rev D

General

The POWERVAR GTS UPM systems are the most advanced, line

interactive, true sinewave UPS products available for your application.

Each model is designed to provide total protection for your system from

a complete range of power quality problems. GTS UPM systems will

protect your installation from normal mode voltage impulses, electrical

noise, sags and surges, brownouts, and blackouts. Each GTS UPM

contains a low impedance isolation transformer, it completely eliminates

common-mode (neutral-to-ground) voltages that are a constant threat

to the reliable operation of microprocessor-based systems. When AC

power is present, GTS constantly lters and conditions the power supply.

When AC power fails, the GTS uses its internal, maintenance-free

battery to supply reserved power to your computer system. Regardless

of whether or not commercial power is present, the GTS is constantly on

the job, ensuring a fully conditioned, safely managed interface between

your computer system and its electrical power supply. Figure 1 illustrates

the basic operation of the GTS UPM.

Figure 1

7A01-00030 Rev D

Sinewave Output

The output voltage of all GTS UPM models is a true, low distortion

sinewave – the kind that the utility company provides to the wall

outlet and the kind that your equipment is designed to work with.

This provides guaranteed compatibility even with the most sensitive

electronic loads.

Voltage Manager

The voltage of the AC power source can often uctuate from its nominal

rating. These deviations in line voltage are tolerated quite well by most

switch mode power supplies (the type used in your computer system).

However, some UPS products may misinterpret these transient changes

in line voltage as a power outage and erroneous battery operation

may occur. This type of activity results in unnecessary strain on the

battery and may eventually shorten its life. POWERVAR’s GTS UPM

products feature Voltage Manager – a circuit that constantly monitors

the AC power source. If minor changes in AC voltage occur, the Voltage

Manager adjusts the input voltage to the UPM circuitry so that erroneous

inverter operations are avoided. Ensuring that the UPM switches to

its batteries only in the event of a true power outage, results in longer

battery life and a lower cost for both maintenance and ownership.

Start Manager

Start Manager is special circuitry that enables the internal batteries and

allows you to start the GTS UPM from either the main AC supply or from

its own internal battery. On occasion, AC power may not be available –

such as when installing a system in a location where the electrical wiring

has not been completed. Start Manager allows you to start the UPM and

its connected system to perform nal tests on both the UPM and the

computer systems it’s powering.

MopUPS Express

Many uninterruptible power systems provide only a basic software

interface with the computer system they protect. MopUPS Express

8 A01-00030 Rev D

combines the signaling capabilities of the GTS rear panel communication

port with the management capabilities of POWERVAR’s communication

software suite. Using your computer’s monitor, MopUPS Express

conveniently displays input and output voltage, output current, power line

frequency, battery voltage, load percentage, and temperature. MopUPS

Express even initiates user dened automatic system shutdowns during

extended power outages. MopUPS Express allows a system operator

to locally or remotely control the shutdown and startup of equipment

connected to the GTS and provides this control either directly or through

the operation of a customized schedule that can be developed to meet

specic operating requirements.

User Replaceable Battery

Eventually every UPM requires a new battery. POWERVAR expects

the battery in your GTS UPM to last a minimum of two years – perhaps

longer if power outages are short and infrequent. The GTS makes

battery replacement by the user fast and easy. It is not necessary to turn

off the UPM or the connected system. The GTS allows the battery to be

“hot-swapped” while the system is running.

2.0 SAFETY INSTRUCTIONS

IMPORTANT - SAVE THESE INSTRUCTIONS

THIS MANUAL CONTAINS IMPORTANT SAFETY INSTRUCTIONS.

KEEP THIS MANUAL HANDY FOR REFERENCE.

CAUTION

A battery can present a risk of electrical shock. Short-circuit currents

can be extremely high and can create severe burns as well as the risk of

re or explosion from vented gases. Always observe proper precautions.

When replacing batteries, use the same quantity, rating and type of

batteries used by POWERVAR. The batteries used in this UPM are

9A01-00030 Rev D

sealed lead-acid and are maintenance free. Proper disposal of batteries

is required. Refer to your local codes for disposal of batteries.

CAUTION

• This UPM contains voltages which are potentially hazardous. All

repairs should be performed by qualied service personnel.

• To reduce the risk of re, connect only to a circuit provided with

20 amperes maximum branch circuit over-current protection in

accordance with the National Electric Code, ANSI/NFPA 70. T

• The UPM has its own internal energy source (battery). The output

receptacles of the UPM may be live even when the UPM is not

connected to an AC Supply.

Safe and continuous operation of the UPM depends partially on the care

taken by users. Please observe the following precautions. (Not following

these could result in warranty being voided).

NOTE:

• Do not disassemble the UPM.

• Do not attempt to power the UPM from any receptacle except a

properly grounded receptacle that matches the input plug provided

with the UPM.

• Do not place the UPM near water or in environments of excessive

humidity.

• Do not allow liquid or any foreign object to get inside the UPM.

• Do not block air vents on the side of the UPM.

• Do not plug appliances such as hair dryers, fans, heaters, etc. into

the UPM.

• Do not place the UPM under direct sunshine or close to heat emitting

sources (excessively warm temperatures will shorten battery life).

• This UPM is intended for installation in a temperature controlled,

indoor area free of conductive contaminants.

10 A01-00030 Rev D

• The AC power supply for the UPM should be conveniently near the

UPM and easily accessible – avoid extension cords or temporary

power strips to power the UPM.

• The total leakage current of the UPM and consumer connected

equipment should not exceed 3.5 mA.

• Not for use in a computer room as dened in the Standard for the

Protection of Electronic Computer/Data Processing Equipment,

ANSI/NFPA 75.

• The socket-outlet shall be installed near the equipment and shall

be easily accessible.

• The battery should be disconnected from the UPM by unplugging

at its quick connectors when maintenance or service work inside

the UPM is necessary.

• Do not dispose of batteries in a re – batteries may explode.

• Do not open or mutilate batteries. Doing so may release electrolyte

or other toxic substances, which may be harmful to the skin, eyes,

or the environment. A battery can present a risk of electric shock

and high short circuit current. The following precautions should be

observed when working with batteries:

• Remove watches, rings, or any other metal jewelry or objects

which may make contact with the battery.

• Use tools with insulated handles.

CAUTION

Risk of Energy Hazard, 12 V, 8.5 Ampere-hour battery for ABCEG251

and ABCEG401. Before replacing batteries, remove conductive

jewelry such as chains, wrist watches, and rings. High energy through

conductive materials could cause severe burns.

CAUTION

Risk of Energy Hazard, 24 V, 8.5 Ampere-hour battery for

ABCEG601. Before replacing batteries, remove conductive

jewelry such as chains, wrist watches, and rings. High energy

through conductive materials could cause severe burns.

Inhaltsverzeichnis

Sprachen:

Andere Powervar UPS Handbücher

Powervar

Powervar 600-1000-1500-2000 VA Bedienungsanleitung

Powervar

Powervar AMETEK 3300 Series Bedienungsanleitung

Powervar

Powervar Ace Plus Series Bedienungsanleitung

Powervar

Powervar 3200 Series Bedienungsanleitung

Powervar

Powervar ACE Series Bedienungsanleitung

Powervar

Powervar ABCEG251 Bedienungsanleitung

Powervar

Powervar Security Plus Bedienerhandbuch

Powervar

Powervar ACE400 Bedienungsanleitung

Powervar

Powervar SG3K-2TXI Bedienungsanleitung

Powervar

Powervar ACDEF6000-22 Bedienungsanleitung

Powervar

Powervar ACDEF700-11 Bedienerhandbuch

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung