Poynting MIMO-3-V2 Bedienungsanleitung

Version: 1.0

Making wireless happen

MIMO-3-V2

User Guide

2 A-MIMO-0003-V2_PCL

Index

1. Packing Check List 3

2. Tools Required 5

3. Optional Accessories 5

4. Introduction 6

5. Installation Instructions 6

6. Antenna Mounting 10

Precautions

7. Cable Routing 11

8. Safety 11

Version: 1.0 3

Packing Check List

Item Description Quantity

1. A-MIMO-0003-V2

Antenna only 1

2. Adhesive Foam

Discs 1

3. M4 x 12mm Stainless

Steel Screws 6

4. Grip Extenders 5*

5. SMA(f) to RP-

SMA(m) Adapter 2*

6. 10mm Threaded

Spigot 1

7. 50mm Threaded

Spigot 1

8. Plastic Nut 1

9. Cable Clips 2

10. Spigot Seal 1

*Quantity will differ with different versions

4 A-MIMO-0003-V2_PCL

Packing Check List

The appearance of each component

Antenna Unit

Adhesive Foam Discs 10mm Threaded Spigot

6x (M4 x 12mm)

Stainless Steel Screws

Plastic Nut

*SMA(f) to RP-SMA(m)

Adapter

50mm Threaded Spigot

Grip Extenders Cable Clips

Spigot Seal

*Antenna with Wi-Fi only

Version: 1.0 5

Tools Required

Item

Safety goggles Drills (Pilot drill (3mm)

and Hole saw (22mm)

or step drill (4 - 22mm))

Masking tape Hand drilling machine

Centre punch Hammer

27mm spanner/

wrench

Drilling template

(Available on www.poynting.

tech/downloads)

Optional Accessories

1. Various Cable extensions are

available

2. Magnetic Base Kit

165

Scale 1:1

Installation Drill Hole Template

6 A-MIMO-0003-V2_PCL

Introduction

This User Guide provides information on the installation

instructions of the MIMO-3-V2 antenna.

Threaded Spigot Mounting

Download the 1:1 drill template from

http://www.poynting.tech/downloads

• Choose the mounting location carefully and a

position at least 50cm from heat sources, with a

clear line of sight to the sky. It is recommended

that the antenna be installed at the highest

possible location on the vehicle’s roof so that

a signal can be received in a 360° radius, clear

of obstacles including parts of the vehicle’s

body and that the mounting surface is as at

as possible. The selected location must have

a conductive metallic surface area which is a

minimum of ±400x400mm to achieve optimal

performance.

• Once you have decided on the location and

checked that there are no obstructions such as

cables or channels below the mounting surface,

for the fastening nut and cables to pass through,

use the downloaded 1:1 drill template to mark

the mounting location.

• To prevent the marking tool or drill sliding off

course, use masking tape over the drilling point

to help hold the drill point in place. The masking

tape also prevents hot shavings from the drill or

hole saw which could penetrate and damage

the painted surface.

• Set the drilling machine to low speed and

carefully drill a pilot hole (Ø3mm drilling bit works

well). Use a Ø22mm metal hole saw or step drill to

open the hole to the required size.

Note: The recommended drill hole diameter for

MIMO-3-V2 is Ø22mm

• Clean the entire surface on which you plan to

mount the antenna. Cleaning is done so as not to

damage the vehicle’s paint and to ensure good

contact of the foam surface to the mounting

Installation Instructions

Version: 1.0 7

Installation Instructions

area.

• Alcohol wipes can be used to remove oil and dirt

from the surface.

• Remove the wax protection paper from the

adhesive foam seal at the base of the antenna.

• Insert the antenna cables and threaded spigot

through the drilled hole.

• Push the antenna down onto the mounting

surface and make sure the antenna is placed

straight and correctly.

• Fit the plastic nut from the inside of the mounting

platform.

• Be careful not to over tighten the nut.

• You may use the 6 x (M4 x 10mm) brass threaded

inserts to further secure the antenna. Please refer

to the drilling template for hole locations. The use

of M4 threaded rod is the preferred fastening

method.

• The 10mm Threaded Spigot should be used

to secure the antenna to a surface structure

of 10mm thickness or less. Likewise, the 50mm

Threaded Spigot should be used to secure the

antenna to a surface structure of 50mm thickness

or less.

Download the Drilling template as shown in image below

165

Scale 1:1

Installation Drill Hole Template

8 A-MIMO-0003-V2_PCL

Installation Instructions

adhesive foam seal

M4 x 12 Stainless

steelscrews

50mm or 10mm

Threaded Spigot

Plastic Nut

Spigot seal

6x (M4 x 10mm )

Threaded Brass Inserts

Threaded Spigot Mounting

Antenna

Adhesive

foam seal

Plastic Threaded Spigot

M4x12mm

Stainless Steel Screws

Spigot Seal

Plastic Nut

Metallic Surface

RF Cable

Ø22

Recommended

Drilling hole Size

Version: 1.0 9

Installation Instructions

Surface mounting

Adhesive surface mounting

• Clean the entire surface on which you plan to

stick the antenna

• Remove Nut, spigot seal and Short spigot from

antenna

• Push the Rf cable into the groove in the plastic

base

• Secure cable with the 2 x cable clips and

4 x (M4 x 12mm) stainless steel screws

• Pull off the one side of the adhesive wax paper of

each of the 6 x adhesive foam discs

Double sided

Adhesive foam discs

Magnets

Non-slip rubber

adhesive discs

M4 x 12 Stainless steel

screws

Adhesive surface mount

M4 x 12 Stainless steel

screws

Cable clips

RF Cable

Optional magnetic base kit

10 A-MIMO-0003-V2_PCL

Installation Instructions

• Place the antenna at the highest point possible

and ensure that there aren’t any surrounding

obstructions to the antenna.

• In order to avoid communication interference,

ensure that the antenna is placed at least 0.5m

away from other antennas and metal objects.

• Avoid installing the antenna near a chimney,

as the smoke and soot emitted by the chimney

can obstruct the signal level achieved by the

antenna.

• Install the antenna away from heat sources and

ammable gases.

Antenna Mounting Precautions

Optional magnetic base kit

Antenna

Adhesive

foam seal for

Adhesive

installation

Metallic Surface or Magnetic

surface for Optional Magnet

Base kit installation

RF Cable

6 x Magnetic Discs

6 x M4 x8mm

Stainless Steel screws

Non scratch rubber

Adhesive discs

Inhaltsverzeichnis

Andere Poynting Antenne Handbücher

Poynting

Poynting XPOL-1 Bedienungsanleitung

Poynting

Poynting RIPPLE Bedienungsanleitung

Poynting

Poynting PUCK-V1 Bedienungsanleitung

Poynting

Poynting PUCK-V1-W Bedienungsanleitung

Poynting

Poynting OMNI 291 Bedienungsanleitung

Poynting

Poynting OMNI-704 Bedienungsanleitung

Poynting

Poynting OMNI-293 Bedienungsanleitung

Poynting

Poynting XPOL-1-5G Bedienungsanleitung

Poynting

Poynting OMNI-493 Bedienungsanleitung

Poynting

Poynting OMNI-402 Bedienungsanleitung

Poynting

Poynting OMNI-702 Bedienungsanleitung

Poynting

Poynting WLAN-61 Bedienungsanleitung

Poynting

Poynting XPOL-24 Bedienungsanleitung

Poynting

Poynting XPOL-2-5G Bedienungsanleitung

Poynting

Poynting A-PUCK-0002-V1-01 Bedienungsanleitung

Poynting

Poynting PUCK-5 Bedienungsanleitung

Poynting

Poynting A-OMNI-0902-V1-02 Bedienungsanleitung

Poynting

Poynting PUCK-V1 Bedienungsanleitung

Poynting

Poynting OMNI-700 Series Bedienungsanleitung

Poynting

Poynting Moray Series Bedienungsanleitung

Poynting

Poynting OMNI-404 Bedienungsanleitung

Poynting

Poynting EPOYNT Bedienungsanleitung

Poynting

Poynting OMNI-403 Bedienungsanleitung

Poynting

Poynting OMNI-706 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung