PR Lighting XR440 BWS Bedienungsanleitung

1/34

XR440 BWS

PR-2462

The user manual contains important information about the safe installation and use of a projector Please read

and follow these instructions carefully and keep the manual in a safe place for future reference

PR LIGHTING LTD

http://www pr-lighting com

2/34

INDEX

SAFETY AND WARNINGS

INSTUCTIONS

●

CLEANING AND MAINTENANCE

●

LUBRICATION

●

TROUBLESHOOTING

3 APPEARANCE

4 INSTALLATION

●

RIGGING

●

POWER CONNECTIONS

●

DMX CONTROL CONNECTIONs

●

DMX TERMINATOR

●

ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP

●

GOBO/COLOR FILTER REPLACEMENT

5 SETUP AND CONFIGURATION

●

FRONT PANEL OPERATION

●

DMX START ADDRESS

●

DMX WIRELSESS CONTROL

●

STAND-ALONE MODE

●

MASTER/SLAVE MODE

6 OPERATION MENU

7 DMX PROTOCOL

8 LED INDICATION

ERROR MESSAGES

TECHNICAL DATA

11 CIRCUIT DIAGRAM AND PCB CONNECTIONS

●

CIRCUIT DIAGRAM

●

PCB CONNECTIONS

12 COMPONENT ORDER CODES

ACCESSORIES

The following items are supplied with the projector and please check:

Name Quantity Unit Remark

G clamps 2 Pcs

XLR Signal Cable 1 Set With Male and female sockets

Safety cord 1 Pc

User manual 1 Pc

Ω clamps 2 Pcs Optional

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without notice Whilst

every care is taken in the preparation of the manual we reserve the right to change specifications in the course of product improvement The

publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from them

Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and / or the unit are in good condition

before installation and use Should there be any damage caused by transportation, consult your dealer and do not use the unit Any damage caused

by improper use will not be assumed by the manufacturer and / or dealer

3/34

1. SAFETY AND WARNINGS

NOTE

Before a projector’s i stallatio , power-o , operatio a d mai te a ce, please carefully read

the safety i formatio herei after!

The followi g safety sig s are used i the user ma ual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

●

Whe u packi g , check if there is tra sportatio damage before usi g the projector. Should there be a y

damage caused by tra sportatio , co sult your dealer a d do ot use it

●

The manufacture is not responsible for loss caused by the user not following the manual or changing the projector

as he/she likes

●

Please be noted that the damage caused by changing the projector at will is not warranted

●

Do not hesitate to contact the dealer or the manufacturer if any questions or advice

●

The projector is for indoor use only, IP20

●

Use only in dry locations Keep this unit away from rain and moisture, excessive heat, humidity and dust Do not

allow contact with water or any other liquids

●

The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

being operated

●

The projector is only intended for installation, operation and maintenance by qualified personnel And the

operation must strictly follow the procedures in the manual

●

No repairable parts in the projector and do not open covers for maintenance by yourself

●

Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned

●

Do not connect this device to any type of dimmer pack

●

After lamp switched on, the minimum distance between the projector and illuminated surface is 10m

●

lens and other optical parts shall be replaced immediately if they have deformed or been damaged, otherwise

the light output will be compromised

●

Before operation, please confirm that all covers(housing) are on and screws tightened It’s forbidden to use a

projector while covers(housing)are off

●

Keep the lamp clean and do not touch it with bare hands

●

While operating it, wear protective items

●

Any electrical connection must be carried out by a qualified person

●

Before installation, please confirm the voltage supplied matches what is required for the projector

●

Each projector must be properly earthed and installed as per related electrical standards

●

Do not use power cord with its insulator damaged and connect the power cord with other cables

●

If the projector is not used or under cleaning,, please hold the plug and unplug it Do not unplug it forcefully

or by pulling the power cable

●

All power cords must conform to related safety and regulations

●

While being operated, the projector should not be under rains or in humidity

●

Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electrical parts’ life will be shortened

4/34

●

There are safety cord holes at the bottom of the base of a projector In view of safety, please run the safety

cord supplied through the safety cord holes for safety support

●

Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

power mains

●

After running for 30minutes, the temperature of the housing of the projector is

℃.After stable

operation , its temperature is

℃.

●

While the lamp is stricken for the first time, there will be smoke and strange smell It’s normal and does

not mean the projector has some defects

●

Do not mount the projector directly on inflammable surface

●

Do not project the beam straightly on combustible items and the minimum distance between the projector

and illuminated items is 10m

●

A projector should be installed with good ventilation and the minimum distance between the projector and

walls is 50cm At the same time, please ensure the fans and air inlets and outlets are workable

INSTRUCTIONS

●

CLEANING AND MAINTENANCE

If a projector can’t start Please check if the fuse is blown up If it does, replace it with a new fuse with same ratings And the

projector has over-temperature protective device If the temperature is too high, the protective device will be triggered to shut the

projector off When it happens, please check if the fans run normally or fan shield is blocked by dust After the issue is solved,

restart the projector

The accumulation of oil, smoke and dust on the lens will compromise the light output Cleaning a projector is very necessary to

ensure a reliable use of it Cooling fans need to be cleaned every 15days Internal lens, reflector and hot mirror need to be cleaned

periodically to optimize light output

Cleaning frequency is to be decided by operations and its environment Use soft cloth and normal detergent for glass for cleaning

work It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days Keep lens clean

and do not touch optical parts with bare hands

●

Before any maintenance and cleaning, please ensure the project is off the power

●

Only qualified person is allowed to do maintenance

●

During maintenance and before maintenance, the projector must be off power

●

To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether it runs or not

●

Do not use alcohol or other organic solvent to clean the housing to avoid damage

●

Do not use any solvent with chemical elements to clean color filters or hot mirror

●

LUBRICATION

To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and

focus lens be lubricated every 2 months High quality and high temperature lubricant/grease is advised

●

TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on  Check the fuse on the power socket

 Check the lamp

The lamp is on but the projector doesn’t respond

to the controller

 Make sure that the fixture’s start address is right

 Replace or repair the XLR signal cable

The projector functions intermittently  Make sure the fan is working well or fans and their shields are not blocked

Beam appears dim, Low in brightness  Make sure the lamp is within its lifespan

 Remove dust or grease from the lenses

The project image appears to have a halo  Carefully clean the lamp, optical lenses and other components

Heavily Defective Beam  Check if lens are in good condition(not cracked)

 Clean dust or grease on the lens

5/34

3. APPEARANCE

The projector’s Structure

1 Front Lens

2 Lens Cover

3 Head Cover

4 Tilt Lock

5 Handle

6 Pan Lock

7 Arm Cover

While transportation, the head should be locked-Tilt Lock(4) and Pan Lock(6) should be at locking positions

Before the use of the projector, unlock both

Rear Pa el of the Base

1 Power Switch

2 Fuse Holder

3 Power Socket

4 3-Pin XLR Socket(Male)

5 Wireless Antenna

6 3-Pin XLR Socket(Female)

7 5-Pin XLR Socket(Male)

8 5-Pin XLR Socket(Female)

Fro t Pa el of the Base

1 XLR Signal Indication

2 Key Func

3 Key UP

4 Key Down

5 Key Enter

6 Wireless Signal Indication

4. INSTALLATION

●

RIGGING

Before moving a projector, Please lock Pan and Tilt Before its operation, please unlock them It’s forbidden to run a

projector with power while it is locked

W-DMXDMX

6/34

Warning

please run the safety cord

through the two holes for safety

Safety cord

Handle

Clamp

Control menu

Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached

to each clamp Hang the fixture on the structure and fasten the screws attached to each clamp (See the WARNING on the

underside of the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the

projector is firmly anchored to avoid vibration and slipping whilst functioning Always ensure that the structure that you are going

to mount the projector to is secure and strong enough to support the weight of a XR 1000 Framing

WARNING:

●

The projector MUST be lifted or carried by the HANDLES instead of clamps

●

For safety the safety cord should afford 10 times the Projector’s weight

●

POWER CONNECTION

Connect the power cord as follows:

L (live) =brown

E (earth) =yellow/green

N (neutral) =blue

Before power connection, please ensure the power supplied must match what the nameplate says It is recommended that each

projector be connected with power separately so that they may be individually switched on and off

●

The earth wire(yellow/green) must be connected to the ground And electrical connection must be in accordance with the

standards concerned

●

If any questions about the electrical installation, do not continue but consult a qualified electrician

7/34

●

DMX CONTROL CONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0 5mm in diameter Connection to and from the projector is via cannon 5 pin (which are included with the

projector) or 5 pin XLR plugs and sockets The XLR's are connected as shown in the figure above

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other XLR plugs and sockets

mustn’t be connected in any way other than mentioned in the above figure The XR330BWS accepts digital control signals in protocol

DMX512 (1990)

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way Eventually connect the last fixture’s DMX output to a DMX

terminator as shown in the figure below

●

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator This prevents

electrical noise from disturbing and corrupting the DMX control signals

The DMX terminator is simply an XLR connector with a 120Ω (ohm) resistor connected across pins 2 and 3, which is then plugged

into the output socket on the last projector in the chain The connections are illustrated below

DMX

Controller

DMX512

Input Output Input Output Input

DMX

Terminator

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain.

PIN 3

PIN 2

8/34

●

ALIGNMENT/INSTALLATION/REPLACEMENT OF A LAMP

Lock the yoke before fitting/replacingthe lamp Just as Shown by Figure 1, after Opening the cover at the rear of the projector by

loosening 8 fastfit screws, you can open the head To adjust the lamp as per Figure 2 Take out the lamp as per the figure 3

Before lamp installation, tighten its power wires well Lamp in and out are opposite orders

●

Don’t touch the internal surface of the reflector and the burner of the lamp with bare hands so as not to

impair the beam output While lamp’s installation, do not damage the metal wire around the burner

●

Please read "Instructions " enclosed with the lamp

●

Do operate the projector while adjusting the lamp

4. After the lamp is aligned well, use cross

screwdriver to tighten the tightening screws at

one side of the lamp to avoid it being loosened

based on procedure 2

Loosen a tightening screw by a

cross screw driver at the lamp's side

Figure1:Loosen 8pcs of fastfit

screws

To adjust the two screws by a cross

screw driver to change the lamp's position

Loosen 4 screws at the fan's two sides

Figure2

：

Lamp adjustment

9/34

●

GOBO REPLACEMENT

DANGER!

Before replaceme t of gobos, the projector must be off the power.

2 Remove the lamp's two wires and push

it obliquely for the removal

2 Remove the cover after its 4 screws are

loosened by a cross screwdriver

4 Connect the lamp wires after a new lamp is in place,

and align and tighten the lamp as per figure2

Figure3

：

Removal of lamp

1 Loosen a tightening screw at the lamp's side

Figure 2

Rotating gobo wheel

Rotator

Gobo

Tightening

spring

Gobo replacement

1 As shown in figure1, disconnect a projector from power Unfasten

the 4 fastfit screws of the cover to remove the cover, and unfasten

the 2 screws of the fan assembly and remove the assembly

2 Pull out the rotator from the rotating gobo wheel forcefully by

fingers as shown in figure2 After replacing the gobo or the rotator,

put the rotator back to the holder

unfasten 2

screws using a

cross screw

driver

remove the fan

component

Figure 1

10/34

5. SETUP AND CONFIGURATION

●

Front Panel Operation

W-DMXDMX

Projector configuration can be set conveniently via push button and LCD display

Launch the projector and press button ENTER for more than 2 seconds to unlock the panel, the LCD will show the function menu of

the projector, each main menu has its submenus and each submenu has a specific function For details, please see the

“OPERATION MENU” section

Press button UP or DOWN if you want to browse through the various Setup Options

Press button ENTER to save your settings or enter the submenu

Press button UP or DOWN to change values(plus or minus)

Press button FUNC, it will return to the upper menu If button FUNC not pressed, the default will show display status automatically

●

DMX START ADDRESS

Each XR 440 BWS must be given a DMX start address so that the correct projector responds to the correct control signals This

DMX start address is the channel number from which the projector starts to “listen” to the digital control information being sent out

from the controller The XR 440 BWS has 4 DMX modes There are standard mode ,short mode extended mode and compatible

mode For example standard mode has 26 channels, so set the No 1 projector’s address 001, No 2 projector’s address 027, No 3

projector’s address 053, No 4 projector’s address079, and so on

Launch the projector Press button ENTER more than 2seconds to unlock panel

Press button ENTER to display DMX address;

Press button UP and DOWN, you can set the address;

Press button ENTER to confirm; after powered on next time, the default will be last value saved

Press button FUNC, it will return to the upper menu

●

DMX WIRELESS CONTROL (If the projector has the function)

The projector has wireless control function with wireless receiver module and antenna for remote control

The setup of it is below:

1 Enter into the projector’s menu Select the menu “Wireless Options” via the bottoms of UP

and

DOWN

Select DMX co trol Mode---- Wireless First or Wireless O ly (Note: do not select XLR ONLY)

Press FUNC to enter into the upper level menu ,select” Unlink Wireless” and press ENTER to confirm the

disconnection

Let “Wireless Transmitter” send out signals and the “W-DMX” indication in the front panel of the base will be on,

which means the wireless control is activated Only after the unit is connected with the wireless transmitter, can it

receive the wireless control signal

●

STAND-ALONE MODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically

Inhaltsverzeichnis

Andere PR Lighting Leuchte Handbücher

PR Lighting

PR Lighting ARC LED 1572 Bedienungsanleitung

PR Lighting

PR Lighting XRLED 700-WBWS Bedienungsanleitung

PR Lighting

PR Lighting XLED 2007 BEAM PR-8123 Bedienungsanleitung

PR Lighting

PR Lighting XL WASH 1200 PR-2905 Bedienungsanleitung

PR Lighting

PR Lighting XR330 BWS Bedienungsanleitung

PR Lighting

PR Lighting XRLED 2500-WFraming Bedienungsanleitung

PR Lighting

PR Lighting AQUA MARINE 580 BEAM Bedienungsanleitung

PR Lighting

PR Lighting THEATRE COLOUR LT Bedienungsanleitung

PR Lighting

PR Lighting JNR-8154B Bedienungsanleitung

PR Lighting

PR Lighting PR-2735 Bedienungsanleitung

PR Lighting

PR Lighting AQUA 350E BWS Bedienungsanleitung

PR Lighting

PR Lighting XR 1700 Wash Bedienungsanleitung

PR Lighting

PR Lighting LS 90 Logo Bedienungsanleitung

PR Lighting

PR Lighting LS 150 Water Bedienungsanleitung

PR Lighting

PR Lighting AQUA LED 1700 FRAMING Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung