Precision FireLight Bedienungsanleitung

FIRELIGHT USER INSTRUCTIONS

Description:

The FireLight is a compact, lightweight low-voltage powered moving pattern projector. The unit is

designed to project a moving pattern of light with an irregular character strongly resembling the appearance

of flames or fire.

The patented refractive optical system is very efficient, using two pattern wheels rotated by gear reduction

motors to produce a bright and dynamic effect pattern using a 35 watt MR-11 incandescent light source. The

motor speed may be adjusted to obtain the desired projection appearance. The projection lens mount slides

to provide easy adjustment of effect focus, allowing further variations in the appearance of the projected

pattern. An internal color filter slot allows for easy installation of gel or dichroic color filters or aperture

plates, which will allow the designer to create anything from highly realistic projections of flame images to

flames with unnatural speed, color, or other characteristics.

Recommended Use

The FireLight fixture is intended for use in applications where the appearance or illusion of fire or flames is

desired, without the hazard or heat of actual flames. The fixture is provided with a 12 volt AC ballast which

will operate from a 120 volt AC power source, or a 120 volt AC lighting dimmer circuit or channel.

PRECISION PROJECTION SYSTEMS INCORPORATED

17508 STUDEBAKER ROAD, CERRITOS, CA 90703-3638

TELEPHONE: 562 865-8552 FACSIMILE: 562 924-7133

WEBSITE www.ppsfx.com EMAIL: [email protected]

General Precautions

The Firelight fixture is intended for indoor special effect applications in theme parks, themed attractions,

themed restaurants or scenic displays, and for any other specialized lighting application where the

appearance of fire or flames is desired, without any of the hazards or difficulties associated with real fire.

The user should be aware that the projector output produces an extremely realistic flame effect, which can

easily be mistaken for an actual fire under the right circumstances. Accordingly, the user is advised to be

careful when installing the unit, and to inform others in areas close to the intended effect or display in order

to avoid “false alarm” calls to local fire departments.

CAUTION

The fixture is intended only for indoor use in dry locations. The unit is not intended for outdoor use,

or for indoor use in close proximity to water or water spray. The fixture is not rated for, nor protected

against water splash, droplets, or mist.

Mounting Precautions

When the fixture is operating, there must be at least 3 inches of free air space clearance around the top and

bottom ventilation slots on the unit case. Do not allow any flammable material to block the fixture output,

contact the fixture case, or obstruct the ventilation slots.

WARNING

Never operate the FireLight fixture with the case in contact with flammable materials. Do not direct

the fixture output onto any flammable materials at distances of less than twelve inches. Flammable

material in contact with, or in close proximity to the fixture case may be ignited by the lamp output,

increasing the risk of fire which may result in serious injury or death. Do not attempt to operate the

unit without all covers closed and secured in place

Electrical Precautions

The FireLight projector is equipped with a 6 inch cord ending in a two pin power connector. The ballast

transformer usually supplied with the unit has a 7 foot output cord with a matching two pin connector. To

connect the FireLight to the transformer, first make sure that the transformer unit is disconnected or turned

off, then align the two connectors and slide them together. The connectors will only fit one way. If they do

not connect, turn one of the connectors over and try again. Once the connector is attached, the transformer

may be plugged in.

WARNING

The FireLight is designed to operate on 12 volt AC or DC electrical power, not 120 volt line voltage.

Application of AC or DC voltages greater than 12 volts, or 120 volt AC line voltage to the FireLight

fixture may cause serious damage to the fixture, and may cause increased risk of electrical shock or

fire, potentially resulting in serious injury or death. Do not attempt to operate the unit with incorrect

or unknown supply voltages, or with substitute power supplies of unknown voltage or DC polarity.

The standard 120 volt AC ballast transformer is compatible with lighting dimmer circuits, and allow the

output of the FireLight fixture to be dimmed like an ordinary lighting fixture. FireLight fixtures for export

applications may be provided with a “Universal Voltage” 12 volt DC power supply or ballast. These units

are not compatible with lighting dimmer circuits, as the voltage agility of the power supply will attempt to

compensate for the drop in line voltage caused by the dimmer.

Mounting

The unit can be mounted in any orientation, keeping in mind that the ventilation areas at the top and bottom

of the unit must remain unobstructed for proper cooling. The unit should also be positioned for easy access

to the door provided for lamp replacement, typically at the rear when mounted in an overhead location.

The FireLight incorporates a mounting yoke with a 1/2" hole at the center for hanging the instrument. The

FireLight is normally attached to a mounting “C-clamp” or other stable means of support using the yoke

mounting hole and an appropriate bolt and washer. The user is responsible for mounting the instrument in a

safe and secure manner. Please consult with local public or workplace safety authorities to determine if any

additional safety restraints, such as safety wires or cables may be required.

Operation

Once connected to the ballast transformer, the FireLight unit will operate as soon as AC power is applied to

the ballast. The lamp and internal motors will begin to operate immediately, and the unit will project a

moving pattern of light with an irregular character resembling the appearance of fire or flames. The fixture is

rated for continuous operation, and in normal use the unit will continue to display the output pattern until

power is removed.

Aiming

The instrument can be pointed using the mounting hole on the yoke as a directional pivot, typically in the

horizontal or lateral direction. Tightening the mounting fastener will lock the instrument in that axis. The

mounting yoke attaches to the sides of the instrument with two thumbscrews. Loosening the thumbscrews

allows for adjustment of the instrument in the second axis, typically in the vertical or elevation direction.

Tightening the yoke thumbscrews will lock the elevation axis.

Effect Adjustments

All controls which vary the appearance of the effect for focus, speed and direction are accessible at the

bottom of the unit, as is the slot for installing a color filter or gel. The screw which secures the color filter is

accessible at the front of the unit near the lens aperture.

The adjustment screws for effect focus and the gel retainer are small thumbscrews, which can be adjusted

manually without tools. The controls for motor speed are multi-turn potentiometers accessible through holes

in the case bottom.. The motor direction controls are slide switches also accessible through slots in the

bottom. These controls can be adjusted using a small slot-blade screwdriver without opening the unit case.

Focus Adjustment

The effect focus can be varied by moving the projection lens. This may be accomplished without opening

the unit case. Two small thumb screws on the lower surface of the unit secure the lens mount. Loosen both

screws slightly, (but do not remove either screw) and use one of them as a handle to slide the lens mount

forward or back until the desired focus is achieved, then tighten both thumb screws securely.

Filter or Gel Installation

A slot for a filter or color gel is provided at the front of the FireLight. A thumbscrew at the front of the unit

retains the filter or gel. Deep color gels may fade or bleach with time, and may require periodic replacement

to maintain the desired color. Color filters or gels should be cut to two inches by two inches or 50mm square

in size, and be no thicker than 1/16 inch, or 1.5mm.

To install a color filter, disconnect power to the unit, remove the thumbscrew next to the output port, and

slide the filter into the slot in the case bottom nearest the thumbscrew. The filter or gel should be pushed into

the slot until it stops, or at least until the edge of the filter or mount is clear of the thumbscrew hole.

Reinsert the thumbscrew and gently tighten it to retain the filter. If it is possible to invert the FireLight unit

when installing a filter or gel, the filter can be simply dropped in or out of the slot after removing the

thumbscrew. Be sure to replace the thumbscrew before turning the FireLight right side up to hold the filter

in place. Reconnect power, then aim and focus the unit as needed for normal operation.

Changing Motor Speed

The two motor speed controls are used to adjust the rate of motion in the output pattern. The motor speed

controls are accessible through small holes in the bottom of the fixture using a small slot blade screwdriver.

Rotating the controls clockwise increases the speed setting, and counterclockwise adjustment will decrease

the setting. The controls are very precise, and several turns may be required to produce a significant change.

The controls do not stop or tighten at the end of their adjustment range, but will continue to spin without

causing any further speed change at minimum or maximum settings.

The adjustment ranges from slow enough to be barely perceptible, to very rapid and turbulent. For the most

natural appearance, both controls should be set from 5 to 7 turns from minimum. Higher or lower settings

may be used depending upon the display requirements. It is normal for the noise level from the effect motors

to increase at higher speed settings, but the motors will not be damaged by prolonged operation even at

maximum speed settings.

Changing Motor Direction

Two switches control the direction of the two effect motors. Each switch controls one of the motors. The

switches can be adjusted using a small slot-blade screwdriver or probe without opening the unit case. The

switches are accessible through slots adjacent to the holes for motor speed adjustment on the bottom panel of

the fixture. The switches are recessed to prevent accidental motor direction changes. Motor direction can be

changed by using a small screwdriver or probe to gently engage the switches, and move the switch slide to

the opposite position. Avoid applying excessive force to the switches.

The motion of the projected effect can be significantly altered by changing the direction that the pattern

wheels rotate. FireLight units are shipped with both motors turning in opposite directions. Due to the side

by side arrangement of the effect wheels, this produces overlapping motion in one direction. With the

motors at nearly equal speeds, the motion adds up to appear like rising and swirling flames. Changing the

direction of one motor will alter the pattern so that some of the effect motion will be upward and some

downward. Reversing both motors will result in flames which flow down, or backwards. If the resulting

motion is not in the desired direction, i.e. down when you want up, such as when the fixture is mounted

inverted, then changing the direction of both motors will correct the pattern motion. To obtain more

swirling, or interaction in the effect, one of the motors should be operated at a slightly faster or slower speed

than the other.

Dimming

The FireLight is compatible with any dimming system that can accept an electronic ballast, and the small

inductive component from the ballast as a load. If you are not certain that your dimmer can accept this type

of load, consult the dimmer specifications or the manufacturer. The effect motor speeds will remain

generally constant, and should not vary as the lamp is dimmed over a large range. The effect drive motors

will not operate, and may not start, at the lowest dimmer settings. Some lamp glow may occur at the

minimum dimmer settings which will permit the motors to operate normally. FireLight units equipped with

“Universal Voltage” DC power supplies cannot be used with dimming circuits

Lamp Replacement

The installation of correct replacement lamps is essential to maintaining the correct appearance of the effect,

and to continued safe operation of the fixture. Replacement lamps with incorrect properties, such as wide

angle or flood output patterns, will result in a dim and badly focused image. Replacement lamps with

incorrect wattage or voltage ratings may cause damage to the fixture.

To change the lamp in the FireLight, first remove power from the unit by unplugging the power cord from

the unit, or at the AC power source. If the unit is mounted close to high wattage fixtures, or if the lamp has

recently failed, the housing, lamp door, lamp, and other internal components will be hot. Allow the unit to

cool for a while before attempting to change the lamp.

WARNING

The direct lamp output is very intense, and when powered, the lamp will become hot very rapidly and

may cause burns if touched. Flammable material in contact with or in close proximity to the lamp

may be ignited by lamp output, causing risk of fire which can potentially result in serious injury or

death. For your safety, never attempt to change the lamp unless you are certain that power is not

applied, and do not attempt to operate the unit with the lamp door, or the unit cover open.

The lamp is accessible through a hinged door located at the rear of the fixture. It is usually not necessary to

disturb the fixture alignment to change the lamp. Unlatch the door by pulling outward on the two snap latch

knobs at the top of the door. The latches operate in a pull/push manner, not by rotating the latch pins. After

both latches are in the out and unlatched position, use the latch knobs to gently pull the hinged panel open.

The access panel will swing open more than 180 degrees, and should not be forced further.

The lamp and lamp socket are attached to the lamp door and will be exposed as the door opens. Be sure the

lamp is cool before touching or attempting to remove it. Support the lamp door and remove the lamp by

grasping the reflector and gently rocking and pulling it straight out of the lamp socket.

CAUTION

Use of the proper type of lamp is essential to the safe and proper operation of the FireLight. Do not

install any replacement lamps greater than 35 watts at 12 volts, or any lamps rated for other than 12

volt use. For general replacement purposes, use only the recommended 35 watt narrow beam MR-11

lamps meeting ANSI specification FTE, or 20 watt narrow beam MR-11 lamps meeting ANSI

specification FTB. Other lamp types, such as colored lamps may be acceptable, but for best results use

only narrow beam lamps. Never exceed the maximum lamp wattage of 35 watts.

Make certain the unit is not powered before installing a replacement lamp. Remove the replacement lamp

from its packaging, and confirm that it is a 12 volt FTE, FTB, or other suitable replacement type. Handle

only the outer edges of the reflector, do not touch the lamp capsule inside the reflector. Install the new

replacement lamp by aligning the body of the lamp to face straight away from the face of the socket, and the

lamp pins to align with the holes in the ceramic lamp socket. Press the lamp straight into the socket until it is

fully seated and centered to point straight away from the face of the socket and the lamp door. Do not twist

the lamp during installation or the lamp and socket could be damaged.

Before closing the lamp door, make sure that both latch knobs remain pulled out in the unlatched position.

The lamp door will not close if either of the latches is in the latched position. Some resistance may be felt as

the latches dock into the socket holes on the fixture, but if the door fails to close fully, check that both latch

pins are pulled out to the unlatched position. After the door is closed flush with the housing, push in on the

latch pins until they snap to the inner and locked position to secure the door. Reconnect the power cord if

disconnected, and apply power to the unit. Observe the fixture for normal operation, and make any aim or

focus adjustments needed for best operation.

Maintenance

The primary maintenance required by the fixture will be lamp replacement. Typical lamp life should be in

the range of 2000 hours with the standard 35 watt FTE lamps recommended. Longer lifetimes may be

obtained with specialty or lower wattage lamps, but the fixture output may be reduced when lower wattage

lamps are used. Colored lamps typically have shorter lifetimes than standard white replacements.

The two DC effect drive gearmotors installed in the unit are sealed and permanently lubricated, and should

not require maintenance over the lifetime of the fixture. Some minor leakage of oil from the motors may be

expected over time, but this is not an indication of motor failure, and is objectionable mainly because of the

dust it tends to capture inside the fixture. After prolonged operation, typically 15 to 20 thousand hours, the

gearmotors may fail to operate due to brush wear or contamination. Temporarily running an inoperative

motor at a high speed setting may clear off contaminated brushes and restore a motor to normal operation.

Worn out brushes will eventually require the installation of replacement effect drive motors.

Aside from lamp replacement, the only maintenance recommended is a periodic cleaning to remove dust

accumulation from the fixture. Convection heat will draw air through the fixture, and dust will eventually

build up outside and inside the fixture over time. Heavy accumulations of dust will reduce the fixture output,

and may eventually obstruct the airflow through the unit, resulting in increased temperatures and reduced

lamp lifetimes. Periodic cleaning with compressed air will remove most light dust contamination. Heavy

dust contamination may require removal of the fixture outer cover for more thorough cleaning using

compressed air, aided by a soft dry brush or tissue paper. Severe contamination by dust in combination with

water mist, fog, and oil or smoke fluid residue may require the use of a cleaning cloth or tissue dampened

with water, or a water based cleaner to thoroughly remove dirt from the interior and optical surfaces of the

fixture. Proper cleaning and a fresh lamp will generally restore the fixture to its original performance.

Troubleshooting

Problem Probable Cause

Fixture completely inoperative No line voltage power, or dimmer setting at minimum

AC circuit fuse or circuit breaker blown

Fixture power cord or ballast power cord unplugged

Defective 12 volt ballast or DC power supply

Motors operate normally, Defective lamp, lamp not properly installed, or

but no lamp output wrong voltage lamp

Lamp operates normally, Incorrect DC polarity when operating the fixture

but no effect motion with a DC power supply

Weak or uneven output pattern Fixture focus set incorrectly

Incorrect lamp type (wide angle) installed

Defective lamp with poor pattern uniformity

Fixture optics dirty or damaged

Jerky pattern motion, or directional motion. Motor speed set too low for reliable motor operation

Fixture effect wheel loose or jammed

Defective effect wheel gearmotor

Fixture buzz or excessive noise Some hum and quiet buzzing sound is normal

Worn or defective effect wheel gearmotor

Replacement lamp cannot be installed Lamp or lamp socket damaged or defective

Incorrect Lamp type

Fixture is excessively hot High ambient temperature at fixture location

Ventilation slots blocked or obstructed

Schematic Diagram

Inhaltsverzeichnis

Andere Precision Projektor Handbücher

Precision

Precision Precision VS11856 Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung