Precor P94 Bedienungsanleitung

P94 (22”) and P84 (16”) Touchscreen Consoles

Installation Guide

WARNING Before you connect any cables to the console, make sure that

the equipment is not connected to any external power source.

1. Ensure all cables feed up through the console mount on the lower equipment.

NOTE (JAPAN ONLY) If using a tuner, install the BCAS card into the lower brackets of the cradle

board before next step (see Figure 5).

2. Place the cradle over and onto the console mount (Figure 1) and feed cables upward. Ensure cables

are not pinched. Cables pinched or damaged during install are not covered under warranty.

3. Secure the console to the console mount on the lower equipment with the four fasteners included

with the lower equipment (Figure 2).

4. Gently seat the display onto the cradle so it rests against the frame (Figure 3).

5. Secure the display to the cradle frame with the four fasteners included with the console (Figure 4).

Install console cradle and display

Figure 1. Cradle onto console mount

Figure 3. Display onto cradle

Before you begin

The P94 22” console ts treadmills and StairClimbers only.

Match the correct number of paddles on the touchscreen to the appropriate lower equipment.

• Single paddle touchscreens = Upright Bike, Recumbent Bike, and StairClimber™ (SCL).

• Dual paddle touchscreens = Treadmill, Adaptive Motion Trainer™ (AMT), and Elliptical (EFX).

Figure 4. Secure display to cradle

Figure 2. Secure

console to mount

Connection Type

BCAS Card (Japan Only)

Power

Set top box/media (used with HDMI-2)

Safety key stop (Treadmill only)

Manual stop (Stairclimber only)

Tuner power

Heart rate sensor

Lower LPCA*

Handle controls (Stairclimber only)

MPA to CPA

TV, coaxial cable

Casting puck (optional) power

CPA to MPA

Ethernet/network

USB-C (from cradle)

Audio

HDMI-1 to tuner/lower cradle

HDMI-2 to set top box/media

HDMI-3 to casting puck (optional)

Casting puck holder 1

Casting puck holder 2

Headphone jack

USB-C port

Display reset button

Console reset button

1010

1111

1212

1313

1414

1515

1616

1717

1818

1919

2020

2121

2222

2323

2424

Connect cables

NOTE Before your begin, plug the CPA to MPA cable to the display and unplug it from the cradle . This will allow better access for the other connection points.

Make the connections as you need them in the order below to allow easy access to connection points. Once nished with other connections, plug it back into the cradle.

1313

1010

1111

1212

1313

1414

1515

1616

1717

1818

1919

2020

2121

2222

2323

2424

Figure 5

2525

Connect the cables that are appropriate for the lower exercise equipment and media conguration (Figure 5). Not all connections are used in any conguration. Review your cable kit.

IMPORTANT A new power supply for the lower exercise equipment is provided in the cable kit and must be installed before connecting cables to the console. Not adding or

replacing the power supply will invalidate the warranty.

P94 22” Touchscreen P84 16” Touchscreen

Figure 5A

*For EFX, bikes, and AMT, clamp the ferrite on to the LPCA cable near end before connecting

(Figure 5A).

Install casting puck and connect cables (optional)

NOTE Casting requires installation of the casting puck and PrecorCast™ server. Refer to

the server installation and conguration guide for casting and server set up. Casting is not

available in China.

1. Plug the HDMI cable from the puck into HDMI-3 connector (Figure 6).

2. Slide puck with holder into holder connectors ( and in Figure 6).

3. Connect the power cable (Figure 6).

Install back cover and power on

1. Ensure cables are routed correctly and not pinched anywhere.

2. Snap back cover into place (Figure 7).

3. Connect unit to power source, turn on, and allow console to

power on.

Connect to a network

Once powered on, connect the console to the network:

1. On the console, press and hold the Stop button for seven seconds to bring up the code entry screen to access

the system settings.

2. Enter code and tap OK.

3. Go to Settings > System Settings > Connectivity.

4. Go to Network Type > Wired (or Wi-Fi) > Go.

5. Tap Congure. From the list, select appropriate network and enter the credentials.

6. Tap Back to return to the Connectivity screen. Your settings will automatically be saved.

Final Checklist

Complete the installation by following this checklist in order below to test performance, function, and network set up.

1 Ensure the new power supply is installed.

2 Install the console as instructed in this document.

3 Ensure that the CPA to MPA cable is reconnected at both ends.

4Verify that any cables from the oor or wall cannot become caught in the moving components of the equipment.

5 Verify equipment has power and is turned on.

6 Verify the motion controls work:

1. Step on the equipment as shown on the labels and place your hands in the correct positions, if applicable.

2. Tap Home on the console. For all equipment except treadmills, manually move on the equipment to wake up the console.

3. Tap QuickStart to begin a workout.

4. Verify the speed and elevation work.

5. Verify the resistance works (bikes, EFX, AMT, SCL).

6. Ensure paddle or paddles work and validate on the cradle display above the paddles.

7. Test the STOP button on the console for (Treadmill and SCL), STOP button on handle of SCL, and emergency stop lanyard (Treadmill only) work.

7 Verify network connectivity:

• Go to Settings > System Settings > Connectivity.

• The IP address eld should be populated (10.15.80.90, for example). If it does not, repeat the Connect to a network section earlier in this document.

8 Set up Live TV option:

• Set PlutoTV (in select markets) or for tuner, scan for channels, or for set-top-box/media refer to https://broadcastvision.com/precorcab/ to congure for your

provider before adding channels.

• For tuner or set-top box/media adapters:

1. Verify channels available match the channel list.

2. Rename channels if necessary.

3. Set the default channel, if applicable.

9 Tap the Home button on the screen and verify:

• For TV option, check navigation for channels (select from channel guide or channel up/down) and volume (up/down)

• Headphone jack and volume controls

• Bluetooth pairing for headset or heart rate chest strap (tap Add Bluetooth icon on screen and follow instructions; for heart rate strap, ensure contact with skin

and allow 7-14 seconds to appear as option on screen)

• USB-C connection (for charging a device and updating software)

10 Verify the heart rate display works:

Begin exercising on the equipment and grasp both touch-sensitive handlebars. The heart icon ashes while the heart rate is read. You must maintain contact with

both metal plates to ensure an accurate reading. Within ten seconds, your heart rate number appears in the HEART RATE (HR) display. Perform the following checks

if a number does not appear:

1. Verify that the HR cable is properly connected in the console.

2. Repeat the test with a different person. In rare instances, it may not work.

9If using PrecorCast, verify casting by selecting option on screen and following prompts. Refer to the PrecorCast™ install guide and online conguration guide.

Figure 6

Figure 7

1919

2020

2121

1212

1919

2020

2121

1212

Dieses Handbuch passt für folgende Modelle