Premier Mounts EST150 Bedienungsanleitung

Single-Stud Short-Throw Projector Wall Mount

Model: EST150

9530-011-021-01

INSTALLATION INSTRUCTIONS

NORTH AMERICA

3130 East Miraloma Avenue

Anaheim, CA 92806 USA

USA and Canada

Phone: 1-800-368-9700

Fax: 1-800-832-4888

Other Locations

Phone: (001) 714-632-7100

Fax: (001) 714-632-1044

EUROPE

Unit 3, The Moorings Business Park, Channel Way

Longford, Coventry, CV6 6RH, UK

Phone: +44 (0)24 7664 4105

Fax: +44 (0)24 7664 4165

EST150

Page 2 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions

Table of Contents

PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR

PURPOSES OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS OR

MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR CAUSES OF ACTION

OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO ANY SUCH USE, ATTACHMENTS OR

MODIFICATIONS.

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE PROPER

SAFETY GEAR AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.

At least two qualied people should perform the assembly procedure. Injury and/or damage can result from dropping or mishandling the

projector.

If mounting to studs, make sure that the mounting screws are anchored into the center of the studs. Use of an edge-to-edge stud nder is

recommended.

Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there are no electrical wires in

wall. Cutting/drilling into an electrical line may cause serious injury.

This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.

Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of impact

Contact Premier Mounts with any questions

(800) 368-9700

[email protected]

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS SHOULD BE READ AND COMPLETELY UN-

DERSTOOD. THE INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP

THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.

Make sure there are no water lines inside the wall where the mount is to be located. Cutting/drilling into a water line may cause severe water

damage to the mounting surface.

Weight Capacity

Maximum projector weight: 25 lbs. THE WALL STRUCTURE MUST BE CAPABLE OF HOLDING FIVE

(5) TIMES THE WEIGHT OF THE PROJECTOR. IF NOT, THEN THE

WALL STRUCTURE MUST BE REINFORCED.

Warning Statements

Heading 1

Weight Capacity 2

Warning Statements 2

Installation Tools 3

Parts List 3

Features 4

Determining the Installation Height 5

Wood Stud Installation 6

Throw Distance Calculation 8

Projector Installation 8

Attaching the Mount Carriage 9

Multiple Mounting Point Installation 10

Single Mounting Point Installation 12

Attaching the Mount Carriage to the Projector Arm 13

Cable Routing (Optional) 14

Securing the Projector (Optional) 14

Mount Adjustment 15

Technical Specications 15

Warranty 16

Disclaimer 16

EST150

Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 3

Projector Arm

(Qty 1)

Mount Carriage

(Qty 1)

Phillips Screwdriver

⅛˝ Drill Bit Electronic Stud Finder

Drill Level

Parts List

Installation Tools

The following tools may be required depending upon your particular installation. They are not included.

Make sure your Premier Mounts product has the following hardware and components before beginning installation. If

there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.

EST150 Hardware

M2.5 x 8mm

Security Screw (Qty 4)

M2.5 x 10mm

Security Screw (Qty 4)

M3 x 16mm

Security Screw (Qty 4)

M3 Flat Washer

(Qty 4)

M4 x 12mm

Security Screw (Qty 4)

M5 x 10mm

Security Screw (Qty 3)

M5 x 12mm

Security Screw (Qty 4)

M6 x 12mm Security

Screw (Qty 4)

#14 x 2” Wood Screw

(Qty 2)

¼-20 x 5/16″ Security

Screw (Qty 1)

M5 Security Wrench

(Qty 1)

Barrel Cap

(Qty 4)

Projector Arm

Cover Plate (Qty 1)

EST150

Page 4 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions

Features

The Single-Stud Short-Throw Projector Wall Mount (EST150) is a simple and elegant tool for mounting a wide variety

of short-throw projectors. Its design allows you to use the same mount even if you need to replace the projector with a

different model. Unique features include a mount carriage that easily slides along the projector arm for quick screen size

adjustments, integrated cable management, and Lock-It™ security screws and barrel for enhanced security.

EST-WP (Optional)

The optional EST-WP wall plate

allows for mounting to 12” or 16”

dual studs. The back plate also

allows lateral shift after installation.

Radial Glide®

Up to 6°of smooth adjustment

in any direction.

Projector Adjustment

Position the projector anywhere along

the projector arm.

Cable Routing

Discreetly manage signal

and power cables through

the projector arm.

Single Stud

Mounts rmly to a

single wood stud.

EST150

Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 5

1) Measure distance from center of lens to the top of the mount carriage (C).

2) Add the distance from the ground to the top of the screen (A). Add the projector manufacturers recommended

offset from the projector manual (B). Add the measurement from Step 1 (C), and then add the mounting screw

offset (D) to the total.

(Example: A + B + C + D = ?)

3) Add the measurements to determine the mounting height mark. Place a mark at the top of the total calculated

height measurement starting from the ground up. This height mark will determine your mounting points.

Refer to the projectors User’s Manual to determine the offset of the projector lens to the top of the

screen/whiteboard (B).

Lens

Mount Carriage

Projector

In order to determine the installation height and throw distance, the mount carriage must be mounted

to the projector.

Top of Screen

Mark

Legend

A - Distance from ground to the top of the

screen/whiteboard (viewable area).

B - Manufacturers recommended offset

measurement. This measurement will

be listed in the Users Manual.

C - Center of the lens to the top of the

projector bracket.

D - If single-stud EST150, add 5.14˝ to

the calculated total.

This total distance will be the location for the

lower mounting point.

Proceed to the “Wood Stud Installation”

section.

Ground

Determining the Installation Height

EST150

Page 6 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions

THE EXACT CENTER OF THE STUD MUST BE LOCATED FOR CORRECT AND SAFE INSTALLATION.

Use an electronic stud nder (not supplied) to

locate the center of the stud that is in the wall.

Wood Stud

Stud nder

Height

Mark

(from page 5)

Wood Stud

Marking

Projector

Arm

Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal

injury or damage to property.

Wood Stud Installation

Mounting Point

Mark

Step 1

Step 2

Use a pencil to mark the rst mounting point, just

above your height mark (from page 5).

Step 3

1) Use the level to make sure the projector arm is level

from side to side.

2) Place the projector arm’s second mounting hole over

the rst mounting point mark, then use a pencil to

mark the upper mounting point.

Two (2) mounting points must be used.

EST150 Installation

EST150

Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 7

After the pilot holes have been drilled, use

two (2) #14 x 2˝ wood screws to mount the projector

arm to the wooden stud.

Step 5

Once the mounting points have been marked, use a

⅛˝ drill bit and portable drill to drill the pilot holes.

Drill Marking

Step 4

Wood Stud

Marking

Projector

Arm

#14 x 2” Wood Screw

Step 6

Use two (2) M5 x 10mm security screws to attach the

projector arm cover plate to the projector arm.

Wood stud not shown

Go to the “Throw Distance Calculation” section on

page 10.

EST150

Page 8 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions

Please review the Operator’s Manual that came packaged with your projector before attaching the upper

mounting bracket. The correct throw distance (the distance from the projector to the screen) must be

determined prior to mounting the projector.

1) Refer to the projectors User’s Manual to

determine the distance from the lens to

the front of the screen (X).

2) Measure the distance from the front of

the lens to the center of the projector (Y).

3) Measure the distance from the wall to the

face of the whiteboard/screen (Z).

4) Add all measurements (X + Y + Z) to

determine projector placement on the

arm assembly. This measurement

will determine where the center of the

mount bracket will be located on the

arm assembly. Please make note of this

measurement.

Front Lens

Rear Lens

Calculations

X = Manufacturers recommended

throw distance

Z = Distance from wall to face of

whiteboard/screen

Front Lens Throw Distance =

(X + Y + Z)

Rear Lens Throw Distance =

(X - Y + Z)

Throw Distance Calculation

The EST150 can be also used as

a wall-mounted standard projector mount as

well as a short throw projector mount. Align

the projector facing the opposite direction

from the wall plate to project the image

across the room. Please take into account

the projectors throw capabilities prior to

mounting in the projector opposite direction.

Proceed to the “Projector Installation” section.

Projector Installation

Locate the mounting points on the bottom of the projector

(see arrows).

Proceed to the “Attaching the Mount Carriage” section.

Attaching the Projector to the Mount Carriage

EST150

Installation Instructions Visit the Premier Mounts website at http://www.premiermounts.com Page 9

Attaching the Mount Carriage

Selecting the Mounting Hardware

1) Insert a small straw or toothpick into the threaded inserts

found on the bottom or top of the projector.

2) Use a pencil to mark the depth of the threaded insert on the

small straw or toothpick.

3) Mark the straw or toothpick 1/8” above the depth of the

threaded insert, as shown in Figure 1.

4) Insert the small straw or toothpick into the remaining

threaded inserts to compare and verify their depth using the

straw or toothpick’s 1/8” allowance mark.

5) Locate the correct diameter screw for the threaded insert.

If the screw you selected is longer than the 1/8”

allowance mark on the small straw or toothpick, as shown

in Figure 2 and Figure 3, do not use this screw. The

screw length must not bypass the mark.

6) Test each size of the screws provided. The correct screws

should thread easily into the mounting point and not pull out

when tension is applied.

Does your projector have multiple mounting points or a

single mounting point?

If your projector has multiple mounting points,

proceed to the “Multiple Mounting Point

Installation” section.

If your projector has a single mounting point, skip to

the “Single Mounting Point Installation” section

on page 14.

Small Straw or Toothpick

Small Straw

or Toothpick

Small Straw

or Toothpick

Marking the 1/8”

Allowance

Depth Plus 1/8” Allowance

Mark

Depth Plus 1/8” Allowance

Mark

EST150

Page 10 Visit the Premier Mounts website at http://www.premiermounts.com Installation Instructions

Step 2

1) Attach the mounting legs to the projector using the

corresponding mounting hardware.

Do not tighten the mounting hardware at this time.

Multiple Mounting Point Installation

Step 1

1) Locate the projector’s mounting points.

2) Position the mounting legs on the projector.

The mounting legs are pre-installed. Depending on the

requirements of your projector, you may remove one of

the mounting legs.

The number and placement of mounting

points on projectors varies between projector

manufacturers. Refer to you projector’s technical

specications for the number and location of the

mounting points on your specic projector.

Step 3

1) If the mounting legs need to be leveled, rotate the

leveling barrels to level the mounting bracket.

2) To raise the mounting legs, rotate the leveling barrel

clock-wise. To lower the mounting leg, rotate the

leveling barrel counter clock-wise.

Raise or lower each of the mounting legs, by

rotating the leveling barrels, until all of the mounting

legs are at an equal height.

• Lower the mounting leg by rotating the leveling

barrel counter-clockwise.

• Raise the mounting legs by rotating the leveling

barrel clockwise.

3) When the desired position is achieved, tighten the

mounting screws to the projector and then tighten the

hex head leg screws with the M5 Allen wrench.

Screws shown for illustration

purposes only.

Mount carriage not shown.

Inhaltsverzeichnis

Andere Premier Mounts Projektorzubehör Handbücher

Premier Mounts

Premier Mounts PDS-004 Bedienungsanleitung

Premier Mounts

Premier Mounts FTP Bedienungsanleitung

Premier Mounts

Premier Mounts Universal Short-Throw Projector Arm UNI-STB Bedienungsanleitung

Premier Mounts

Premier Mounts PDS-URPM Bedienungsanleitung

Premier Mounts

Premier Mounts MAG-Ext Bedienungsanleitung

Premier Mounts

Premier Mounts PBM-070L Bedienungsanleitung

Premier Mounts

Premier Mounts Polaris MAG Bedienungsanleitung

Premier Mounts

Premier Mounts Polaris MAG Bedienungsanleitung

Premier Mounts

Premier Mounts PP-STKR Bedienungsanleitung

Premier Mounts

Premier Mounts PDS-017 Bedienungsanleitung

Premier Mounts

Premier Mounts Universal Projector Mount PBL-UMS Bedienungsanleitung

Premier Mounts

Premier Mounts Low-Profile Dedicated Projector Mount... Bedienungsanleitung

Premier Mounts

Premier Mounts Low-Profile Universal Projector Mount... Bedienungsanleitung

Premier Mounts

Premier Mounts GearBox GB-SEC1B Bedienungsanleitung

Premier Mounts

Premier Mounts POLARIS MAG Bedienungsanleitung

Premier Mounts

Premier Mounts PCS-5000 Bedienungsanleitung

Premier Mounts

Premier Mounts PDS-010 Bedienungsanleitung

Premier Mounts

Premier Mounts Polaris Universal Projector Mount MAG Bedienungsanleitung

Premier Mounts

Premier Mounts SpiroLock SPI-EXT Bedienungsanleitung

Premier Mounts

Premier Mounts Nova-EXT Bedienungsanleitung

Premier Mounts

Premier Mounts PBC-UMS Bedienungsanleitung

Premier Mounts

Premier Mounts PDS-009 Bedienungsanleitung

Premier Mounts

Premier Mounts PBC-FCTA Bedienungsanleitung

Premier Mounts

Premier Mounts PBM-UNI Bedienungsanleitung

Beliebte Projektorzubehör Handbücher anderer Marken

Optoma

Optoma BX-AL133B Bedienungsanleitung

PEERLESS

PEERLESS PE 1120 Leitfaden

Osram

Osram SIRIUS HRI Series Handbuch

Presentation Switchers

Presentation Switchers PS111 Bedienungsanleitung

Kramer

Kramer VIA GO Bedienungsanleitung

Yamaha

Yamaha PJL-112 Stücklistenhandbuch

Swedstyle

Swedstyle CL23AA02ZA25E Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric 236CB Betriebsanleitung

Epson

Epson BrightLink 475Wi Bedienungsanleitung

Acer

Acer WP100 Bedienungsanleitung

i3 i3board Bedienungsanleitung

CHIEF

CHIEF HB-43E Bedienungsanleitung

Biamp

Biamp Modena Hub Service-Handbuch

NEC

NEC MP10RX Bedienungsanleitung

Panamorph

Panamorph DCR-S3 Bedienungsanleitung

Exact solutions

Exact solutions FRAME-EVO-P10 Bedienungsanleitung

CHIEF

CHIEF VCM103S Bedienungsanleitung

InFocus

InFocus LP70+ Leitfaden