Pro's Kit SS-979 Bedienungsanleitung

SS-979 2 In 1 SMD Hot Air Rework Station

User’s Manual

1st Edition,2020

SAFETY INSTRUCTIONS

WARNING

Warnings and cautions are placed at critical points in this manual to direct the

operator’s attention to significant items. They are defined as follows:

WARNING

Failure to comply with a WARNING may result in serious injury or death.

CAUTION

Failure to comply with a CAUTION may result in injury to the operator, or damage

to the items involved.

NOTE: A NOTE indicates a procedure or point that is important to the process

being described.

EXAMPLE: AN EXAMPLE is given to demonstrate a particular procedure, point

or process.

Be sure to comply with following WARNINGS and CAUTIONS for your safety.

WARNING

Do not change or disassemble any components related to this product, it may

cause product damaged.

When replacing the fuse, be sure to turn off the power before operating.

During working period, do not turn off the power suddenly, the heat gun should be

placed on the bracket until cool off, otherwise it will damage the product。

CAUTION

When the power is ON, the temperature of the hot air and the nozzle ranges from

100 to 500℃(212 to 932℉); the temperature of soldering iron ranges from 200 to

480℃(392-896℉).

To avoid injury to personnel or damage to items in the work area, observe the

following:

** Do not aim the hot air toward personnel or touch the metal parts near the

nozzle.

** Do not use the product near combustible gases or flammable materials.

** Avoid potentially dangerous work condition involving high temperature area.

** After use, the power should be off

** Change the components or tip after cutting off power and waiting to cool it.

** Do not touch the metallic parts near the tip.

** Do not strike the hand piece against hard surfaces.

** Be sure the unit is grounded. Always connect power to a grounded receptacle.

** Do not disassemble the machine.

** Do not modify the unit.

** Use Pro’sKit replacement parts only.

** Do not wet the unit or use the unit with wet hands.

** Remove power cord by holding the plug –not the wires.

** Make sure the work area is well ventilated.

** Keep away from children.

Function diagram:

1. Hot air nozzle

2. Heat gun bracket

3. LED screen

4. Set key

5. Airflow knob

6-1 Heat gun power switch

6-2 Soldering iron power switch

7. Station power switch / Power

socket

8. UP ▲key

9. Down ▼key

10. Solder iron stand

11. Cleaning sponge

12. Soldering iron socket

Packing List：

SS-979 2 In 1 SMD Hot Air Rework Station (include bracket) x1

Heat gun x1

Air nozzle x 3

Soldering iron x1

Iron stand（with cleaning sponge, copper cleaner）x1

Power cord x1

User’s manual x1

Features:

Microprocessor-controlled, closed circuit sensor design, high power and quick

warm-up times

Adjustable air volume and temperature, suitable for a variety of applications.

6-1

6-2

Handle with sensor design, switching work & sleep mode for real-time

operation convenience.

Auto cool-off process to prolong the life of heating element

Comes with brushless motor provides long service life, quiet in operation

Soldering iron conforms to CE, ESD safety regulations.

Heat insulation handle with ergonomic design ensures user safety and comfort.

The soldering iron adopts ceramic heating element, providing stable power and

fast heating speed.

Ideal for heating shrinks, viscidity removal, lacquer removal, preheating and

more.

Specification:

Model No.

SS-979B

SS-979H

Power input

220V-240V ～50Hz

Power consumption

760W

Soldering power

60W

Soldering iron temperature

200-480℃

Hot air temperature

100-500℃

Soldering iron output voltage

24V～

Hot air output voltage

220V-240V~

Temperature display

LED

Soldering iron heating element

Alumina ceramic heater

Hot air heating element

Metal heating core

Air volume

120L/min(Max)

Equipment noise

<45dB

Plug type

Fuse type

250V / 5A

Certificate

CE, RoHS, ESD

Weight (with soldering iron)

2.5Kg

Dimension (mm)

170x170x140 (include bracket)

Optional Replacement

Replacement Nozzle：

IC Package

Model No.

ID (mm)

9SS-969-A1

Ø4.3

9SS-969-A2

Ø7.4

9SS-969-A3

Ø11.2

Replacement Soldering Iron：

Replacement heater

9SS-900N-HT

Replacement hand piece

9SS-900N-SI

Replacement Tips:

Application

1.Suitable for desoldering multiple components.

2.Ideal for heating shrink, viscidity removal, lacquer removal, preheating and

more.

3.Electronic maintenance and device welding operation.

Operation Instruction

1.Put the rework station ready and place handle on the bracket.

2.Connect the power cord to the power receptacle on the back panel of the

station.

3.Set the blast nozzle (large caliber nozzle preferred).

4.Switch the power on, the screen displays last set value then display “SLP“, it

represents standby mode. (Available in microcomputer with digital LED)

5.Press “▲”or “▼” key as to set up the temperature.

6.Adjust the airflow knob to set up the required air volume.

7.Hold the handle, the equipment begins to heat. Rotate the airflow knob in order

to set proper air volume and operate normally when temperature is stable.

8.Put the handle back on the bracket after work, the SMD station switched from

heating mode to cooling - off mode automatically. When the temperature is

lower than 100℃, the station switching to standby mode.

9.Cut the power off and unplug the power cord if there is no operation for a long

time.

Attention

Please set up the temperature as lower as possible in high airflow volume as to

prolong heating element service life and better IC chips protection.

Setting Up Temperature

1.In the power on state, press the "set" key to select the conversion between air

temperature and soldering iron temperature.

2.Press “▲”or “▼”key to set up the temperature, the screen displays the setting

temperature.

3.Press “▲” once the temperature degree increase 1℃, and the screen displays

4.the setting temperature. Press “▼” once the temperature degree decrease 1℃,

and the screen displays the setting temperature. When press the “▲”or “▼”

key continuously, the temperature will increase or decrease rapidly, after the

key is released, the screen displays setting temperature.

5.Put the handle back on the holder after work, the SMD station switched from

heating mode to cooling - off mode automatically. When the temperature is

lower than 100℃, the station switch to standby mode.

6.Press "▲", “▼" at the same time to start the machine and restore the factory

settings.

7.Press "set" key to start the machine, and select the temperature unit ℃/ ℉.

Calibrating Temperature

1.Press the "set" and "▲" keys at the same time to calibrate the temperature of

the air gun, and then input the measured actual temperature value.

2.Press the "set" and “▼” keys at the same time to calibrate the temperature of

the soldering iron, and input the actual temperature value for measurement at

this time.

3.Press "set" to select the adjustment position and exit, press "▲" “▼” to adjust

the number.

Note

Temperature for hot air measurement is located in the middle point of about 3mm

inside the air nozzle.

Note:

Explanation of symbols

A. “SLP”represents the temperature is lower than 100℃in standby mode, while

the handle put on the bracket.

B. “S-E” represents the switch turned on but the connector of heat gun (soldering

iron) did not connect to the station properly or the sensor of heat gun

(soldering iron) damaged, please replace a new heat gun (soldering iron).

1.The air outlet and its surrounding area may be very hot. Be cautious of scald.

2.The heat gun shall not be put on the working table or other place except its

bracket.

3.Please keep the air outlet unblocked.

4.Place the heat gun on its bracket after the work, and keep it cool naturally and

turn into standby mode, then switch the power off.

5.The distance between the air outlet and the object shall be no less than 2mm.

6.Choose suitable nozzle in accordance with working requirements. Different

nozzles may result in different temperatures.

7.When the soldering iron is not in use, please put it on the soldering iron stand.

8.If the temperature is too high, the service life of soldering iron tip will be

reduced, so the suitable working temperature should be selected。

9.Clean the iron tip with cleaning sponge regularly。

10. When the soldering iron is used continuously for a long time, remove the iron

tip once a week to remove the oxide。

11. After use, the iron tip should be wiped clean and coated with a new tin layer

to prevent oxidation of the iron tip.

12. The temperature of different types of soldering iron tip may be different. The

best way to adjust the temperature is to use a special thermometer for

measuring the tip. (refer to "temperature calibration")

Fuse Replacement

When fuse is blown, replace with the same type of fuse. (see below picture)

1. Unplug the power cord from the power receptacle.

2. The fuse holder is located under the AC power receptacle, use the slotted (–)

screwdriver to loosen the fuse bracket

3. Replace the fuse with new one

4. Put the fuse holder back in place

Basic Troubleshooting Guide

WARNING

To avoid personal injury or equipment damage, disconnect power cord before making any

servicing to the equipment.

Problem 1: The unit has no power / display does not light up.

1.Check if the unit is switched ON.

2.Check the fuse, replace with the same type of fuse if blown.

3.Check the power cord and make sure there is no disconnection.

4.Verify that the unit is properly connected to the power source.

5.Check if local voltage matches the product requirement.

Problem 2: The temperature of the SMD station is not rising.

Description: Display lights up but the temperature of heat gun is relative low and

not heating up.

Solution: Heat gun cord or heating element may be damaged, please replace a

new heat gun.

Problem 3: Heat gun temperature is intermittent.

Description:

Display lights up but the heat gun temperature rises and falls uncontrollably.

The temperature is less than 50℃, and no longer heating up in working state.

Solution:

Heat gun plug may be loose from the receptacle, unplug the heat gun and

re-attach.

Heat gun cord or heating element may be damaged, please replace new heat

gun.

Problem 4: The temperature of soldering iron tip cannot be increased

Description:

The temperature display shows the temperature, but the temperature of the

soldering iron does not reach the set relative temperature or is not heated.

When the display temperature is less than 50 ℃and does not heat up again,

or when the temperature of the soldering iron tip rises intermittently.

Solution:

Is the soldering iron wire damaged? Please replace the soldering iron handle.

The heating core may be damaged, please replace it with a new one

Please refer to " Refer to checking for breakage in the heating element ".

Problem 5: The temperature of soldering iron tip or hot air is too low or too

high

Description: The temperature deviation between the temperature display and

the soldering tip is large

Solution:

Is the soldering iron tip aging seriously? Please replace or clean the soldering

head.

Is the calibration correct? Please recalibrate

Checking for breakage of the heating element and cord assembly

Disconnect the plug and measure the resistance value between the connecting

plug pins as follows.

If the values of 'a' and 'b' are outside the above value, replace the heating

element (sensor) and/or cord assembly .Refer to Procedures 1 and 2. If the value

of “c”is over the above value, remove the oxidization film by lightly rubbing with

sand-paper or steel wool the points as shown.

Heating element broken

Disassembling the Unit

1. Turn the nut 1 counterclockwise and remove the tip enclosure 2, the tip 3 .

2. Turn the nipple 4 counterclockwise and remove it from the iron.

3. Pull both the heating element 6 and the cord assembly 11 out of the handle 12.

(Toward the tip of the iron.)

4. Pull the grounding spring 5 out of the D-sleeve.

Measure when the heating element is at room temperature.

1. Resistance value of heating element (resistance between the 2 red lines) ≈4Ω

2. Resistance value of sensor (resistance between the 2 blue line) ≈50Ω

If the resistance value is not normal, replace the heating element.

Replace the heating element.

1.De-solder the damaged heating element leads and remove it.

2.Replace a new one and solders to PC board properly.

3. Solder the two leads of heater to the other side of PC board, bend the leads at

right triangle when soldering to prevent short-circuit

After heating element replaced:

1.Measure the resistance value between pins 3 & 4 or pins 3 & 5 or pin 4 & 5. If it

is not ∞, the heating element or sensor may touch the housing ground.

Eliminates the problem first; otherwise, it will damage the PCB

2.Measure the resistance value between all leads to confirm that the leads are

not twisted and that the grounding spring is properly connected.

Soldering iron cord damaged

Test the soldering iron cord

Check the resistance between the pin of the plug and the wire on the terminal.

Pin 1: Black Pin 2: Red Pin 3: White Pin 4: Black Pin 5: Red Pin

The value should be <2Ω. If it is more than 2Ω or ∞, the soldering iron need to be

replaced.

Note:

The actual wiring mode shall be subject to the circuit diagram, and the color of

lead sheath will not be informed

Heating element lead diagram

Andere Pro's Kit Elektrowerkzeuge Handbücher

Pro's Kit

Pro's Kit PT-0721 Bedienungsanleitung

Pro's Kit

Pro's Kit SI-168U Bedienungsanleitung

Pro's Kit

Pro's Kit SI-168U Bedienungsanleitung

Pro's Kit

Pro's Kit SS-331B Bedienungsanleitung

Pro's Kit

Pro's Kit GS-23K Bedienungsanleitung

Pro's Kit

Pro's Kit PT-5208U Bedienungsanleitung

Pro's Kit

Pro's Kit Pro'sKt SS-621 Series Bedienungsanleitung

Pro's Kit

Pro's Kit PT-1805 Bedienungsanleitung

Pro's Kit

Pro's Kit PT-1801 Bedienungsanleitung

Pro's Kit

Pro's Kit PT-1806 Bedienungsanleitung

Pro's Kit

Pro's Kit SS-615 Series Bedienungsanleitung

Pro's Kit

Pro's Kit SS-988 Bedienungsanleitung

Pro's Kit

Pro's Kit HT-5501 Bedienungsanleitung

Pro's Kit

Pro's Kit SI-137 Bedienungsanleitung

Pro's Kit

Pro's Kit SS-628 Series Bedienungsanleitung

Pro's Kit

Pro's Kit SS-611A Bedienungsanleitung

Pro's Kit

Pro's Kit SS-612A Bedienungsanleitung

Pro's Kit

Pro's Kit PT-1210 Bedienungsanleitung

Pro's Kit

Pro's Kit SI-B166 Bedienungsanleitung

Pro's Kit

Pro's Kit PT-5501 Bedienungsanleitung

Pro's Kit

Pro's Kit PT-1362U Bedienungsanleitung

Pro's Kit

Pro's Kit SS-611 Bedienungsanleitung

Pro's Kit

Pro's Kit PT-1207 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch