PRO.SIS.TEL. LOG2010 Bedienungsanleitung

LOG2010 (20-17-15-12-10m)

Assembling procedures:

After you open the box, find and prepare parts as following:

Handle wi h care he preassembled par s.

Boom use square pipes.

Front and back elements use round pipes

All measure are me rics in mm.

Be aware, put a little lubrification on stainless steel bolts because if screwed down fast, getting hot,

could stiff, (general rules alid for all stainless steel bolts).

Arrange square pipe, in line, in a stepping down sequence following labels and drawing.

Innestare i tubi l’uno dentro l’altro, ed imbullonarli tra loro con gli appositi bulloni. Le teste dei

Insert the smaller square pipe end in the larger square pipe end, insert the bolt from bottom to top

side and make sure that bolt head take place in the larger hole pressing on the inner square pipe.

Boom

The A label joints are on the front side, the B label joints are on the rear antenna side, both refered

to mast-boom joint plate.

On the antenna boom are preinstalled already the wire elements insulators and RF wire line. After

that the boom is completed, connect the line wires to next one, taking care to cross them.

RF wire line, back and front alluminum elements take place on the bottom boom face.

If you are assembling antenna on easels, pre enting RF line wires damages, disconnect them in

coincidence with easel, taking care to reconnect them back when assembling end.

If you ha e easy access to your tower rotating mast pipe , than install boom-mast plate on the

antenna boom and install it on the tower, taking care to ha e RF lines and insulators facing down.

Take out from the package the back dipole round tubes, you will get them preassembled, just pull

them out from the main pipe, following the tube tapering sequence, find the connection holes, when

they are coincident, put and screw down the bolt, make sure to ha e the bolt head down in the larger

hole as in the picture below. Don’t forget to lubrificate a bit the stainless steel bolts.

Screw down all nuts. Make sure that all bolt heads are aligned on the same side.

Follow the same procedure for all tube connections.

When you ha e both half alluminum element ready, than procede to assembly the center as in the

picture below. Make sure to ha e 8cm in between the line connection bolts.

Cen er view of back elemen dipole (long one)

When back element is assembled do the same procedure with front element as in the picture below

Cen er view of he fron dipole (shor one)

Boom-mast plate

After than you ha e installed antenna boom on the mast procede to install both alluminum dipoles

on the boom bottom face. Install the short one on the front side, using four 80x6MA bolts and

predrilled square counter-plate. Install the long one on the back side using four 80x6MA bolts as

counter plate use the foot of the upholder wires pipe. In both cases insert bolts from bottom side.

Before to screw down the self-looking nuts, check that both dipoles are correctly spaced from the

nearest element, Make sure that they are in square and screw down the bolts to ha e a solid cross.

Install the top trussed wire doing a knots on the back eye bolt, pass trought the uphold pipe hole and

go to the front side eye bolt, pull to ha e the boom a little bit bended on the upper side, (banana

effect) and close down the knot. Install in the same way, the back dipole upper guy wire, to ha e it

like a gull wings.

In the package you will find two rolls of black UV resistant plastic wire. They are the external

insulated loop on which will take places the wires elements ends.

Find the end ha ing the eye and install it on the bolt coming out from the boom, front side, screw

down a self-looking nut, so the eye can’t come loose. Next one, mo ing toward the plastic wire, you

will find a short piece of alluminum with an insulator, fit the insulator in the alluminum dipole end,

walk going at back dipole, fit the short black round insulator in the dipole end, and than go to the

boom end and insert the turnbuckle eye on the bolt end coming out from the boom pipe.

Follow the same procedure with the second one half loop. When both wires are in place, pull wires

screwing the turnbuckle. Make sure that both half loop are well balanced looking toward the boom,

it MUST be straight.

In the package there are 6 couple of steel wires elements, they are gal anized steel, protected with

black UV resistent PVC with both ends eye terminated. Unroll the wires elements, select them by

longer to shorter. Get the longer wires couple and starting from the back antenna side, connect each

one element end to his correspondent RF line, one eye to the insulator bolt, the other one end on

the corrispondet U bolt placed on the main loop insulated wire. Repeat this procedure for all

elements.

Install balun 1:2 and connect both wire end to RF line, connect the coax line taking care to run it

on the upper boom face use plastic belts or tape to hold it in place.

New Balun ersion

Main an enna diagram – Top view

Back side view Side view Fron

When completed antenna will looks like the one in the picture.

Af er han all par s are assembled make sure ha all nu s are igh ned

Images and drawings are for information purposes only and may not be the same as the

finished product, the manufacturer reserves the right to make changes or modifications

without prejudice to the final specifications.

Fea ures:

Antenna perform in the range 13-30Mhz, optimized in coincidence with Ham radio bands.

Performance may change due en ironimental conditions in which is installed.

Take care to install it at least 5 or more meters (15 or more ft) o er the ground.

Bands: 20-17-15-12-10m

Impedence: 50 ohm with original 2:1 balun installed

SWR: < 1:1,5

Boom 5,9m + 1,8m (18+6ft)

Accept Mast 50mm (2in) or 60mm. (optional)

Rotating 5.4m (17ft)

Weight about 20Kg (44lbs)

Average gain 6-9 Dbi

F/B 10 - 20dB

Maximum power 3KW pep ssb

Wind survive: 130Km/h

WARNING!!!

Do no ins all he an enna in he vicini y of exposed power lines or o her sources of power a

risk of ligh ning, you may be killed or seriously injured. Make sure anyone does no even

come in o con ac wi h i acciden al during use

Ins all he an enna on properly dimensioned suppor s o hold he load even under s ormy

wind condi ions.

The fall of all or par of i could hi people and / or hings wi h unrecoverable damages.

In case, he responsibili y is o be solely charged by he user.

This manual is an in egral par of he produc , keep i handy.

Dear buyer,

thank you for purchasing a Pro.Sis.Tel antenna ..

Making it we have used the best materials available on the market, worked and finished

with the best care possible allowed by the state of art.

Use it within the rating for which it was built and will serve you faithfully for many years.

In case of doubts or concerns, our technical department is always ready to provide all the

necessary help.

If you are satisfied with it tell the others, otherwise ...... tell to us.

Your opinion and your suggestions will help us to improve even more our products.

Best regards

nnamaria Fiume IK7MWR

Made in Italy

W RNING! Defend the environment

isposing components and materials

The antenna consists mainly of aluminum, in the event of disposal, conferred the scrap to a specialized

disposal center, in compliance with the requirements of local law.

Inhaltsverzeichnis

Andere PRO.SIS.TEL. Antenne Handbücher

PRO.SIS.TEL.

PRO.SIS.TEL. PST-27 Installationsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-20VF Installationsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-34TV Bedienungsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST152VC Installationsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-RD34T Bedienungsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-53-40 Bedienungsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-152TV Bedienungsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-DDR5 Bedienungsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-32 Installationsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-1524TV Bedienungsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST Bedienungsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-30VF Bedienungsanleitung

PRO.SIS.TEL.

PRO.SIS.TEL. PST-40VF Installationsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung